Multiquip manual EM-120SM Initial START-UP

Page 15

This section is intended to assist the operator with the initial start-up of the EM-120SM mixer.It is extremely important that this section be read carefully before attempting to use the mixer in the field.

DO NOT use your mixer until this section is thoroughly understood.

EM-120SM — INITIAL START-UP

STARTINGTHE ENGINE (gasoline only)

The following steps outline the procedure for starting the engine. Depending on the type of engine employed in the mixer the steps may vary slightly. If your mixer has an electric motor disregard this section.

1.Move the fuel shut-off lever (Figure 4) to the ON position.

CAUTION:

Failure to understand the operation of the EM- 120SM mixer could result in severe damage to the mixer or personal injury.

See Figure 1 (Page 10) for the location of any control referenced in this manual.

LUBRICANTS

ENGINE OIL

1.Remove the engine oil dipstick from its holder.

2.Determine if the engine oil is low, add correct amount of engine oil to bring oil level to a normal safe level.

CLUTCH OIL

1.Check the oil level in the clutch compartment, fill with 30 SAE engine oil if needed.

REDUCTION GEAR OIL

1.Check the oil level in the reduction gear compartment, fill with 90 SAE transmission oil if needed.

ZERK GREASE FITTINGS

1.Check the zerk grease fittings at each end of the mixing drum. These grease fittings lubricate the dumping mechanism. If the dumping handle is stiff or hard to move lubricate these fittings.

FUEL

1.If your mixer has a gasoline engine, determine if the engine fuel is low. If fuel is low, remove the fuel filler cap and fill with unleaded gasoline.

CAUTION:

Handle fuel safely. Motor fuels are highly flammable and can be dangerous if mishandled. DO NOT smoke while refueling. Do not attempt to refuel mixer if the engine is hot or running. Always allow engine to cool before refueling.

Figure 4. Fuel Shut-OFF Lever

2.To start a cold engine, move the choke lever (Figure 5) to the CLOSED position.

Figure 5. Choke Lever

3.Move the throttle lever (Figure 6) away from the slow position, about 1/3 of the way toward the fast position.

Figure 6.Throttle lever Lever

ESSICK EM-120SM — OPERATION AND PARTS MANUAL — REV. #5 (03/29/10) — PAGE 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model EM-120SM Page Essick EM-120SM Operation and Parts Manual REV. #5 03/29/10 Table of Contents Parts Ordering Procedures Best Deal! Order via Internet Dealers OnlyOrder via Fax Dealers Only Operation and Safety Decals Essick Safety InstructionsRules for Safe Operation General SafetyMaintenance Safety Rules for Safe OperationEmergencies EM120SM Mixer Specifications EM-120SM SpecificationsEM-120SM General Information Mixer EM-120SM ControlsElectric Motor Connection Electric Motor Wiring InformationEM-120SM Electric Motor Electric MotorEM-120SM -TOWING StepCheck the following before towing Paddle Blade Adjustment, Steel Drum EM-120SM Paddle Blade AdjustmentEM-120SM Initial START-UP Stoppingthe Mixer gasoline EM-120SM Initial START-UPMixing Starting the Electric MotorEM-120SM Maintenance Clutch Adjustment Procedure EM-120SM MaintenanceCleaning Clutch Adjustment Mechanical 12 CF MixerEM-120SM Maintenance Engine Troubleshooting EM-120SM -TROUBLESHOOTING EngineEM-120SM -TROUBLESHOOTING ENGINE/MIXER Explanation of Code in Remarks Column Items Found In the Remarks ColumnItems Found In the Items Number Column EM-120SM 1TO 3 Units EM-120SM- Suggested Spare PartsEM-120SM Mixing Drum Assy Paddle Shaft EM-120SM Mixing Drum AssyEM-120SM Paddle Shaft Assy TOW END Cast Paddle EM-120SM Frame Assy EM-120SM Frame Assy EM-120SM CAB Assy EM-120SM CAB Assy EM-120SM -WISCONSIN Engine Assy Pilot Bushing EM-120SM -WISCONSIN EngineassyEM-120SM Honda Engine Assy EM-120SM Honda Engine Assy EM-120SM Electric Motor Assy Bushing EM-120SM -TRANSMISSION Assy Shifter Shaft Minimum Order Special Expediting ServicePayment Terms Freight PolicyEssick EM-120SM Operation and Parts Manual REV. #5 03/29/10 HERE’S HOW to GET Help
Top Page Image Contents