Multiquip manual EM-120SM -TOWING, Step, Check the following before towing

Page 13

NOTE

Before towing, check with local and state laws for proper compliance.

The tow bar and chain must be properly attached to the mixer and towing vehicle prior to towing. Refer to the following installation instruction:

Step 1.

Insert the Draw Bar into the main frame. Secure, utilizing the 3/4" bolt (grade 5) and nylock nut.Tighten to 100 foot pounds.

STEP 1

DRAW BAR

BOLT & NUT

Step 2.

Install the chain through the hole located between the frame gusset and frame angle. Loop the chain together and place under the Draw Bar.Secure with connector link.

INSERT CHAIN THROUGH

STEP 2

THE HOLE

 

 

DRAW BAR

FRAME ANGLE

 

FRAME GUSSET

CONNECTOR LINK

Step 3.

Extend the chain along the length of the Draw Bar, remove excess chain (slack) and secure to bottom connector link. Secure the chain to the towing vehicle, using the connector link.

EM-120SM —TOWING

STEP 3

VEHICLE

CONNECTOR LINK

DRAW BAR

REMOVE EXCESS

CHAIN (SLACK)

BOTTOM CONNECTOR LINK

NOTE

It is critical that the length of the chain be properly adjusted, to prevent the Draw Bar and the front mixer stand from dropping to the ground (contact) in the event the Draw Bar becomes disconnected from the towing vehicle.

If a new safety chain is required use P/N 13363. For a new connector link use P/N 01004.

CAUTION:

Check the following before towing:

BALL HITCH COUPLER

1.Check vehicle hitch, ball, and coupler for signs of wear or damage. Replace any parts that are worn or damaged before towing.

2.Use only the 2" ball diameter as indicated on your coupler. Use of any other ball diameter will create an extremely dangerous condition which can result in separation of the coupler and ball or ball failure.

3.Be sure the coupler is secured to the hitch ball and the lock lever is down tight and locked.

Recheck tightness again after towing about 50 miles.

4.Check that trailer safety chains are properly connected.

ESSICK EM-120SM — OPERATION AND PARTS MANUAL — REV. #5 (03/29/10) — PAGE 13

Image 13
Contents Model EM-120SM Page Essick EM-120SM Operation and Parts Manual REV. #5 03/29/10 Table of Contents Best Deal! Order via Internet Dealers Only Parts Ordering ProceduresOrder via Fax Dealers Only Operation and Safety Decals Essick Safety InstructionsRules for Safe Operation General SafetyRules for Safe Operation Maintenance SafetyEmergencies EM120SM Mixer Specifications EM-120SM SpecificationsEM-120SM General Information Mixer EM-120SM ControlsEM-120SM Electric Motor Electric Motor Wiring InformationElectric Motor Electric Motor ConnectionStep EM-120SM -TOWINGCheck the following before towing Paddle Blade Adjustment, Steel Drum EM-120SM Paddle Blade AdjustmentEM-120SM Initial START-UP Mixing EM-120SM Initial START-UPStarting the Electric Motor Stoppingthe Mixer gasolineEM-120SM Maintenance Cleaning EM-120SM MaintenanceClutch Adjustment Mechanical 12 CF Mixer Clutch Adjustment ProcedureEM-120SM Maintenance Engine Troubleshooting EM-120SM -TROUBLESHOOTING EngineEM-120SM -TROUBLESHOOTING ENGINE/MIXER Items Found In the Remarks Column Explanation of Code in Remarks ColumnItems Found In the Items Number Column EM-120SM 1TO 3 Units EM-120SM- Suggested Spare PartsEM-120SM Mixing Drum Assy Paddle Shaft EM-120SM Mixing Drum AssyEM-120SM Paddle Shaft Assy TOW END Cast Paddle EM-120SM Frame Assy EM-120SM Frame Assy EM-120SM CAB Assy EM-120SM CAB Assy EM-120SM -WISCONSIN Engine Assy Pilot Bushing EM-120SM -WISCONSIN EngineassyEM-120SM Honda Engine Assy EM-120SM Honda Engine Assy EM-120SM Electric Motor Assy Bushing EM-120SM -TRANSMISSION Assy Shifter Shaft Payment Terms Special Expediting ServiceFreight Policy Minimum OrderEssick EM-120SM Operation and Parts Manual REV. #5 03/29/10 HERE’S HOW to GET Help