Multiquip manual EM-120SM General Information

Page 10

EM-120SM — GENERAL INFORMATION

GENERAL

The Essick EM-120SM Series plaster and mortar mixers are shipped completely assembled and have been factory tested.

The drum batch capacity of these mixers is between 3.5 and

4.0bags. With proper care, they will give continuous service year-after-year.

These mixers can be powered by either gasoline or electric motors.The power from the engine is transmitted via the clutch/ reduction assembly directly to the paddle shaft. Therefore providing high mixer torque and eliminating V-belts .

BEFORE STARTING

Before starting the engine, read the engine owners manual and thoroughly understand the safety information.

Check the items listed below:

OIL LEVELS

Be sure to check the oil levels in the engine and engine reduction unit before starting the unit.

HARDWARE

Check all hardware on the mixer before starting. Periodically inspect all hardware. Loose hardware can contribute to early component failure and poor performance. Use the torque chart below as a general guideline and keep all hardware tight:

HARDWARE DIA

TORQUE (LB./FT.)

5/16"- 18

24

3/8" - 24

37

1/2" - 13

39

1/2" - 13 (Grade 8)

90

GASOLINE ENGINE CARE

For care and operation of the gasoline engine, refer to the engine manufacturer’s operating instructions furnished with the engine. We recommend draining and refilling the engine crankcase at least every thirty hours of operation. Check the engine oil level daily.

GASOLINE MIXER OFF/ON SWITCH

This feature is on gasoline engine mixers only. Located on the side of the engine cover. The purpose of this switch is to start and stop the mixer in normal operation.

ELECTRIC MOTOR MIXER OFF/ON SWITCH

This feature is on electric motor mixers only.This switch is located on top of the motor. Lift the engine cover to gain access to this switch.The purpose of this switch is to start and stop the mixer in normal operation. Never use the electric motor in an explosive environment.

ENGINE THROTTLE AND CHOKE CONTROLS

Please refer to the engine owners manual for specific instructions.

PAGE 10 — ESSICK EM-120SM— OPERATION AND PARTS MANUAL — REV. #5 (03/29/10)

Image 10
Contents Model EM-120SM Page Essick EM-120SM Operation and Parts Manual REV. #5 03/29/10 Table of Contents Best Deal! Order via Internet Dealers Only Parts Ordering ProceduresOrder via Fax Dealers Only Essick Safety Instructions Operation and Safety DecalsGeneral Safety Rules for Safe OperationRules for Safe Operation Maintenance SafetyEmergencies EM-120SM Specifications EM120SM Mixer SpecificationsEM-120SM General Information EM-120SM Controls MixerElectric Motor Electric Motor Wiring InformationEM-120SM Electric Motor Electric Motor ConnectionStep EM-120SM -TOWINGCheck the following before towing EM-120SM Paddle Blade Adjustment Paddle Blade Adjustment, Steel DrumEM-120SM Initial START-UP Starting the Electric Motor EM-120SM Initial START-UPMixing Stoppingthe Mixer gasolineEM-120SM Maintenance Clutch Adjustment Mechanical 12 CF Mixer EM-120SM MaintenanceCleaning Clutch Adjustment ProcedureEM-120SM Maintenance EM-120SM -TROUBLESHOOTING Engine Engine TroubleshootingEM-120SM -TROUBLESHOOTING ENGINE/MIXER Items Found In the Remarks Column Explanation of Code in Remarks ColumnItems Found In the Items Number Column EM-120SM- Suggested Spare Parts EM-120SM 1TO 3 UnitsEM-120SM Mixing Drum Assy EM-120SM Mixing Drum Assy Paddle ShaftEM-120SM Paddle Shaft Assy TOW END Cast Paddle EM-120SM Frame Assy EM-120SM Frame Assy EM-120SM CAB Assy EM-120SM CAB Assy EM-120SM -WISCONSIN Engine Assy EM-120SM -WISCONSIN Engineassy Pilot BushingEM-120SM Honda Engine Assy EM-120SM Honda Engine Assy EM-120SM Electric Motor Assy Bushing EM-120SM -TRANSMISSION Assy Shifter Shaft Freight Policy Special Expediting ServicePayment Terms Minimum OrderEssick EM-120SM Operation and Parts Manual REV. #5 03/29/10 HERE’S HOW to GET Help