Multiquip WM70SH8C, WM70SH5C manual Safety chain connection, Tow Bar to Mixer Connection

Page 11

safety chain connection

CAUTION

NEVER tow the mixer with the safety chain removed. The safety chain is intended to prevent complete separation of the mixer from the towing vehicle in the event of a tow bar failure.

Tow Bar to Mixer Connection

Reference Figure 1 for the installation of the safety chain.

1.Insert the tow bar through the round opening at the bottom of the mixer stand.

Align the hole on the tow bar with the hole on the mixer frame, and insert 1/2-inch bolt through tow bar and frame. Secure tow bar to frame with 1/2-inch nyloc nut. Tighten to 40 ft.-lbs.

MIXER

 

STAND

 

 

1/2-INCH NYLOCK

SAFETY CHAIN

NUT, GRADE 5

 

STEP 2

 

2.Route the safety chain through the holes just above the tow bar, located on each side of the mixer stand.

Loop the chain together and place under the tow bar. Secure the loop with the connector link.

3.Extend the safety chain along the length of the tow bar, looping it through the tow bar's connector link. Remove any excess chain slack.

4.Connect the free end of (connector link) the safety chain to the towing vehicle. Remember it is critical that the length of the chain be properly adjusted, to prevent the draw bar and the front of the mixer stand from dropping to the ground (contact) in the event the draw bar becomes disconnected from the towing vehicle.

CAUTION

DO NOT tow the mixer unless the mixing drum is completely empty. ALWAYS make sure the drum latch pin is fully engaged to the right (Figure 2) of the drum stop block. This will keep the drum from rotating.

TOW BAR

 

CONNECTOR LINK

 

SAFETY CHAIN

STEP 1

1/2-INCH BOLT,

CLEVIS SAFETY HOOK

STOP

DRUM LATCH PIN

(TOWING VEHICLE)

STEP 3

GRADE 5

SAFETY CHAIN

 

 

 

 

CONNECTOR LINK

STEP 4

Figure 1. Tow Bar and Safety Chain Installation

BLOCK

TOW OR LOCKED

POSITION

Figure 2. Drum Latch Pin (Tow or Locked Position)

WM70SH5C/wm70sh8c Mixer • operation and parts manual — rev. #0 (06/07/11) — page 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents WM70SH5C Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsWM70SH5C/WM70SH8C Table of ContentsChoose from three easy options Burn hazards Safety informationSaFeTY MeSSageS Explosive fuel hazardsGeneral SaFeTY Before servicing equipment Mixer SaFeTYEngine SaFeTY gaSoline ModelS onlY Power Cord/Cable Safety Fuel SaFeTY gaSoline ModelS onlYGeneraTor SaFeTY EleCTriC MoTor SaFeTY eleCTriC ModelS onlY„ alWaYS shutdown engine before transporting ToWing SaFeTYEnvironMenTal SaFeTY Tow Bar to Mixer Connection Safety chain connectionLbs kg SpecificationsDimensions DimensionsApplication Power PlantsEngine Maintenance Hardware General informationComponents Engine Oil Check InspectionBefore Starting Blade Check Controls Start/Stop SwitchesFuel Check Belt CheckInitial Servicing Basic engineAdjust paddles as shown in Figure Paddle blade adjustmentStart-up Turn the engine switch to the on positionBelt Slip Lever Start/Stop Position Stopping the Mixer OperationMixing/Dumping Page First Every Maintenance engineEngine oil Engine air cleanerInstall drain bolt with sealing washer and tighten securely Drum Bearing Bracket Lubrication Maintenance MixerBall Socket and Clamp Face Maintenance Drum Head SealsMain Gear and Drive Pinion Alignment Wheel BearingsTires Wear/Inflation InspectTooth Contact between Main Gear and Drive PinionGear Lubrication Tires/Wheels/Lug NutsNever use an pneumatic air gun to tighten wheel lug nuts Lug Nut Torque RequirementsStart all wheel lug nuts by hand Suspension Mixer CleaningMixer Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Defective or worn drum support Adjust if necessaryDrum difficult to discharge tilt Blades adjusted too tight Replace sealsWiring diagram Explanation of Code in Remarks Column Rope, recoil starter GX160 Element, air cleaner GX160Suggested Spare Parts BeltInstructions DE Sécurité Nameplate and decalsEM948630 Decal, push to stop English Decal, safety instructions English 515275Decal, safety instructions french DECAL, handle kick back, safety grate Crush hazardFrame assy 507444 514842491692 530023Engine END Paddle shaft assyEM202898 514752492584 NUT, Lock 1/2 EM202896 492399 B0LT, 1/2 X EM200292Steel tub assy 491008 530028C3249 20561-001Axle assy 8164 34698115 3005Engine assy 513868 EM969013 NUT 3/8 NC G5 506488EM905016 492378 Bolt 3/8 NC X 1-3/4 G5 490957Cabinet assy 491010 520620EM505186 503723FreigHT poliCY Terms and conditions of sale partsPage HERE’S HOW to GET Help

WM70SH8C, WM70SH5C specifications

The Multiquip WM70SH5C and WM70SH8C are cutting-edge water pump models designed for construction and industrial applications. These robust machines are specifically engineered to handle a variety of heavy-duty pumping tasks, making them an essential asset for contractors and industrial operators alike.

The WM70SH5C model is powered by a reliable 5.5 HP Honda engine, while the WM70SH8C variant features an 8 HP Honda engine, providing additional power for demanding applications. Both models are equipped with a high-performance centrifugal pump, ensuring efficient water transfer and quick operation. They are capable of moving large volumes of water, making them suitable for dewatering, irrigation, and other water management tasks.

One of the standout features of the WM70SH series is their impressive maximum flow rate. The pumps can deliver up to 2,000 gallons per minute, significantly reducing the time required for water removal in flooded areas or construction sites. This efficiency is crucial in maintaining project timelines and ensuring safety in work environments.

Durability is another key characteristic of these models. The WM70SH5C and WM70SH8C are built with heavy-duty materials, including a cast iron pump housing and aluminum alloy components, which resist corrosion and ensure a long operational lifespan. Additionally, their rugged construction allows them to withstand harsh working conditions, making them reliable even in the toughest environments.

Ease of use and maintenance is also a priority in the design of these pumps. The WM70SH series features an easy-access maintenance panel that simplifies routine checks and service procedures. The equipped oil alert system helps prevent engine damage by shutting down the engine if the oil level is too low, providing peace of mind for operators.

Both models are designed for portability, with integrated handles and a lightweight frame that facilitate easy transportation. This mobility makes the WM70SH series ideal for contractors who need to move equipment frequently from one job site to another.

In summary, the Multiquip WM70SH5C and WM70SH8C water pumps stand out in the market for their powerful performance, robust construction, and ease of use. They are designed to deliver efficiency, reliability, and durability, making them an excellent choice for any water pumping requirements in construction and industrial applications. With features catering to the demands of heavy-duty tasks, these pumps enhance productivity while ensuring operational safety.
Top Page Image Contents