Multiquip WM70SH5C Adjust if necessary, Replace seals, Defective or worn drum support, Brackets?

Page 34

 

troubleshooting

 

 

 

 

 

 

 

Mixer Troubleshooting

 

 

Worn or defective V-belt?

Replace V-belt.

Blades will not rotate.

Adjustment lever mis-aligned?

Check position of adjustment lever.

 

Adjust if necessary.

 

 

Material leaking from drum ends.

Worn or defective paddle shaft seals?

Replace seals.

 

Defective or worn drum support

Apply grease to bracket or replace.

 

brackets?

Drum difficult to discharge (tilt)

 

Blades adjusted too tight.

Adjust blades until they almost touch

 

 

side walls of drum.

 

 

page 34 — WM70SH5C/wm70sh8c Mixer • operation and parts manual — rev. #0 (06/07/11)

Page 33 Page 35
Image 34
Page 33 Page 35
Contents WM70SH5C Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningTable of Contents WM70SH5C/WM70SH8CChoose from three easy options Explosive fuel hazards Safety informationSaFeTY MeSSageS Burn hazardsGeneral SaFeTY Engine SaFeTY gaSoline ModelS onlY Mixer SaFeTYBefore servicing equipment EleCTriC MoTor SaFeTY eleCTriC ModelS onlY Fuel SaFeTY gaSoline ModelS onlYGeneraTor SaFeTY Power Cord/Cable SafetyEnvironMenTal SaFeTY ToWing SaFeTY„ alWaYS shutdown engine before transporting Safety chain connection Tow Bar to Mixer ConnectionSpecifications Lbs kgDimensions DimensionsGeneral information Power PlantsEngine Maintenance Hardware ApplicationComponents Before Starting InspectionEngine Oil Check Belt Check Controls Start/Stop SwitchesFuel Check Blade CheckBasic engine Initial ServicingPaddle blade adjustment Adjust paddles as shown in FigureTurn the engine switch to the on position Start-upBelt Slip Lever Start/Stop Position Mixing/Dumping OperationStopping the Mixer Page Maintenance engine First EveryInstall drain bolt with sealing washer and tighten securely Engine air cleanerEngine oil Drum Head Seals Maintenance MixerBall Socket and Clamp Face Maintenance Drum Bearing Bracket LubricationWheel Bearings Main Gear and Drive Pinion AlignmentTires/Wheels/Lug Nuts InspectTooth Contact between Main Gear and Drive PinionGear Lubrication Tires Wear/InflationStart all wheel lug nuts by hand Lug Nut Torque RequirementsNever use an pneumatic air gun to tighten wheel lug nuts Mixer Cleaning SuspensionMixer Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Replace seals Adjust if necessaryDrum difficult to discharge tilt Blades adjusted too tight Defective or worn drum supportWiring diagram Explanation of Code in Remarks Column Belt Element, air cleaner GX160Suggested Spare Parts Rope, recoil starter GX160Nameplate and decals Instructions DE SécuritéDECAL, handle kick back, safety grate Crush hazard Decal, safety instructions English 515275Decal, safety instructions french EM948630 Decal, push to stop EnglishFrame assy 530023 514842491692 507444Paddle shaft assy Engine END492399 B0LT, 1/2 X EM200292 514752492584 NUT, Lock 1/2 EM202896 EM202898Steel tub assy 20561-001 530028C3249 491008Axle assy 3005 34698115 8164Engine assy 492378 Bolt 3/8 NC X 1-3/4 G5 490957 EM969013 NUT 3/8 NC G5 506488EM905016 513868Cabinet assy 503723 520620EM505186 491010Terms and conditions of sale parts FreigHT poliCYPage HERE’S HOW to GET Help

WM70SH8C, WM70SH5C specifications

The Multiquip WM70SH5C and WM70SH8C are cutting-edge water pump models designed for construction and industrial applications. These robust machines are specifically engineered to handle a variety of heavy-duty pumping tasks, making them an essential asset for contractors and industrial operators alike.

The WM70SH5C model is powered by a reliable 5.5 HP Honda engine, while the WM70SH8C variant features an 8 HP Honda engine, providing additional power for demanding applications. Both models are equipped with a high-performance centrifugal pump, ensuring efficient water transfer and quick operation. They are capable of moving large volumes of water, making them suitable for dewatering, irrigation, and other water management tasks.

One of the standout features of the WM70SH series is their impressive maximum flow rate. The pumps can deliver up to 2,000 gallons per minute, significantly reducing the time required for water removal in flooded areas or construction sites. This efficiency is crucial in maintaining project timelines and ensuring safety in work environments.

Durability is another key characteristic of these models. The WM70SH5C and WM70SH8C are built with heavy-duty materials, including a cast iron pump housing and aluminum alloy components, which resist corrosion and ensure a long operational lifespan. Additionally, their rugged construction allows them to withstand harsh working conditions, making them reliable even in the toughest environments.

Ease of use and maintenance is also a priority in the design of these pumps. The WM70SH series features an easy-access maintenance panel that simplifies routine checks and service procedures. The equipped oil alert system helps prevent engine damage by shutting down the engine if the oil level is too low, providing peace of mind for operators.

Both models are designed for portability, with integrated handles and a lightweight frame that facilitate easy transportation. This mobility makes the WM70SH series ideal for contractors who need to move equipment frequently from one job site to another.

In summary, the Multiquip WM70SH5C and WM70SH8C water pumps stand out in the market for their powerful performance, robust construction, and ease of use. They are designed to deliver efficiency, reliability, and durability, making them an excellent choice for any water pumping requirements in construction and industrial applications. With features catering to the demands of heavy-duty tasks, these pumps enhance productivity while ensuring operational safety.
Top Page Image Contents