Multiquip WM70SH8C, WM70SH5C manual Components

Page 15

components

Figure 4 illustrates the basic components and controls of the WM70SH5C/WM70SH8C mixer.

1.Tires Ply — The tire ply (layers) number is rated in letters. This mixer uses 13-inch 4-ply tires.

2.Engine Cover — Lift this cover to gain access to the engine compartment.

3.Belt Slip Lever — When starting, this lever should be move upward and to the left. For mixing, place the lever in the down position. See attached decal located adjacent to lever.

4.ON/OFF Switch — This switch is located on the side of the engine cover. When activated, it will shut down the engine.

5.Latch — Use this latch to secure the engine compartment cabinet.

6.Drum Bearing — There is a sealed bearing on each end of the mixing drum. Bearings are packed and sealed at the factory and require no further maintenance.

7.Mixing Paddles — Used in the mixing of material.This unit uses four different types of paddles to provide a fast uniform mix.

8.Bag Cutter — This feature allows compound mixing bags to be opened easily, therefore allowing the contents of the bag to fall directly into the mixing drum.

9.Safety Grill — Provided for operator safety.This safety grill is designed to keep hands and solid objects out of the mixing drum when in use.This grill should be closed at all times when mixer is in use. DO NOT remove the grill or grill opening bar. Keep the grill clean by washing it down daily.

10.Dump Handle — Pull this handle downward to dump the contents of the drum. Push the handle upward to return the drum to its vertical position.

11.Safety Grill Lock Handle — To prevent injury to hands and arms, the safety grill should ALWAYS be locked when the mixing of plaster or mortar is required. Also when transporting the mixer, the safety grill should be locked. The safety grill should only be unlocked when cleaning of the blades and drum is required.

12.Pivot Point/Zerk Fitting — There is a zerk grease fitting on each end of the mixing drum. These fittings lubricate the dumping mechanism. Lubricate both fittings at least twice a week.

13.Dump Handle Release Pin — Pull this pin outward (spring loaded) to release the drum, then pull down on the dump handle to place the drum in the dump position. When drum is in dump position, pin will automatically lock drum.

14.Mixing Drum — Mixing materials such as mortar, plaster are to be placed into this drum for mixing. Always clean the drum after each use.

15.Tow Bar/Coupler — This mixer uses a 2-inch coupler or pintle towbar.

16.Safety Chain — This mixer uses a 3/16-inch thick, 72-inches long, zinc-plated safety chain. ALWAYS connect the safety chain when towing.

17.Forklift Pockets — When lifting of the mixer is required, use these fork lift pockets to lift the mixer. Remember to insert the forks of the forklift a minimum of 24 inches into the lift pockets.

18.Chock Blocks — Place these blocks (not included as part of the mixer package) under each mixer wheel to prevent rolling.

WM70SH5C/wm70sh8c Mixer • operation and parts manual — rev. #0 (06/07/11) — page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents WM70SH5C Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsWM70SH5C/WM70SH8C Table of ContentsChoose from three easy options Burn hazards Safety informationSaFeTY MeSSageS Explosive fuel hazardsGeneral SaFeTY Mixer SaFeTY Engine SaFeTY gaSoline ModelS onlYBefore servicing equipment Power Cord/Cable Safety Fuel SaFeTY gaSoline ModelS onlYGeneraTor SaFeTY EleCTriC MoTor SaFeTY eleCTriC ModelS onlYToWing SaFeTY EnvironMenTal SaFeTY„ alWaYS shutdown engine before transporting Tow Bar to Mixer Connection Safety chain connectionLbs kg SpecificationsDimensions DimensionsApplication Power PlantsEngine Maintenance Hardware General informationComponents Inspection Before StartingEngine Oil Check Blade Check Controls Start/Stop SwitchesFuel Check Belt CheckInitial Servicing Basic engineAdjust paddles as shown in Figure Paddle blade adjustmentStart-up Turn the engine switch to the on positionBelt Slip Lever Start/Stop Position Operation Mixing/DumpingStopping the Mixer Page First Every Maintenance engineEngine air cleaner Install drain bolt with sealing washer and tighten securelyEngine oil Drum Bearing Bracket Lubrication Maintenance MixerBall Socket and Clamp Face Maintenance Drum Head SealsMain Gear and Drive Pinion Alignment Wheel BearingsTires Wear/Inflation InspectTooth Contact between Main Gear and Drive PinionGear Lubrication Tires/Wheels/Lug NutsLug Nut Torque Requirements Start all wheel lug nuts by handNever use an pneumatic air gun to tighten wheel lug nuts Suspension Mixer CleaningMixer Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Defective or worn drum support Adjust if necessaryDrum difficult to discharge tilt Blades adjusted too tight Replace sealsWiring diagram Explanation of Code in Remarks Column Rope, recoil starter GX160 Element, air cleaner GX160Suggested Spare Parts BeltInstructions DE Sécurité Nameplate and decalsEM948630 Decal, push to stop English Decal, safety instructions English 515275Decal, safety instructions french DECAL, handle kick back, safety grate Crush hazardFrame assy 507444 514842491692 530023Engine END Paddle shaft assyEM202898 514752492584 NUT, Lock 1/2 EM202896 492399 B0LT, 1/2 X EM200292Steel tub assy 491008 530028C3249 20561-001Axle assy 8164 34698115 3005Engine assy 513868 EM969013 NUT 3/8 NC G5 506488EM905016 492378 Bolt 3/8 NC X 1-3/4 G5 490957Cabinet assy 491010 520620EM505186 503723FreigHT poliCY Terms and conditions of sale partsPage HERE’S HOW to GET Help

WM70SH8C, WM70SH5C specifications

The Multiquip WM70SH5C and WM70SH8C are cutting-edge water pump models designed for construction and industrial applications. These robust machines are specifically engineered to handle a variety of heavy-duty pumping tasks, making them an essential asset for contractors and industrial operators alike.

The WM70SH5C model is powered by a reliable 5.5 HP Honda engine, while the WM70SH8C variant features an 8 HP Honda engine, providing additional power for demanding applications. Both models are equipped with a high-performance centrifugal pump, ensuring efficient water transfer and quick operation. They are capable of moving large volumes of water, making them suitable for dewatering, irrigation, and other water management tasks.

One of the standout features of the WM70SH series is their impressive maximum flow rate. The pumps can deliver up to 2,000 gallons per minute, significantly reducing the time required for water removal in flooded areas or construction sites. This efficiency is crucial in maintaining project timelines and ensuring safety in work environments.

Durability is another key characteristic of these models. The WM70SH5C and WM70SH8C are built with heavy-duty materials, including a cast iron pump housing and aluminum alloy components, which resist corrosion and ensure a long operational lifespan. Additionally, their rugged construction allows them to withstand harsh working conditions, making them reliable even in the toughest environments.

Ease of use and maintenance is also a priority in the design of these pumps. The WM70SH series features an easy-access maintenance panel that simplifies routine checks and service procedures. The equipped oil alert system helps prevent engine damage by shutting down the engine if the oil level is too low, providing peace of mind for operators.

Both models are designed for portability, with integrated handles and a lightweight frame that facilitate easy transportation. This mobility makes the WM70SH series ideal for contractors who need to move equipment frequently from one job site to another.

In summary, the Multiquip WM70SH5C and WM70SH8C water pumps stand out in the market for their powerful performance, robust construction, and ease of use. They are designed to deliver efficiency, reliability, and durability, making them an excellent choice for any water pumping requirements in construction and industrial applications. With features catering to the demands of heavy-duty tasks, these pumps enhance productivity while ensuring operational safety.
Top Page Image Contents