Multiquip WM70SH8C, WM70SH5C manual Engine oil, Engine air cleaner

Page 25

maintenance (engine)

Perform the scheduled maintenance procedures as defined by Table 6 and below:

DAILY

„„Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as necessary. Check and retighten all fasteners as necessary. Check the gearbox for oil leaks. Repair or replace as needed.

WEEKLY

„„Remove the fuel filter cap and clean the inside of the fuel tank.

„„Remove or clean the filter at the bottom of the tank.

„„Remove and clean the spark plug (Figure 21), then adjust the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm). This unit has electronic ignition, which requires no adjustments.

GAP

0.024-0.028 IN.

 

 

(0.6-0.7 MM.)

Figure 21. Spark Plug Gap

Engine oil

1.Drain the engine oil when the oil is warm as shown in Figure 22.

2.Remove the oil drain bolt and sealing washer and allow the oil to drain into a suitable container.

3.Replace engine oil with recommended type oil as listed in Table 5. For engine oil capacity, see Table 2 (Engine Specifications). DO NOT overfill.

4.Install drain bolt with sealing washer and tighten securely.

5.

OIL FILLER CAP

 

 

DIPSTICK

DRAIN SEALING

BOLT WASHER

Figure 22. Engine Oil (Draining)

engine air cleaner

1.Remove the air cleaner cover and foam filter element as shown in Figure 23.

2.Tap the paper filter element (Figure 23) several times on a hard surface to remove dirt, or blow compressed air [not exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter element from the air cleaner case side. NEVER brush off dirt. Brushing will force dirt into the fibers. Replace the paper filter element if it is excessively dirty.

3.Clean foam element in warm, soapy water or nonflammable solvent. Rinse and dry thoroughly. Dip the element in clean engine oil and completely squeeze out the excess oil from the element before installing.

DANGER

DO NOT use gasoline as a cleaning solvent to avoid creating the risk of fire or an explosion.

Figure 23. Engine Air Cleaner

WM70SH5C/wm70sh8c Mixer • operation and parts manual — rev. #0 (06/07/11) — page 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents WM70SH5C Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsWM70SH5C/WM70SH8C Table of ContentsChoose from three easy options SaFeTY MeSSageS Safety informationExplosive fuel hazards Burn hazardsGeneral SaFeTY Engine SaFeTY gaSoline ModelS onlY Mixer SaFeTYBefore servicing equipment GeneraTor SaFeTY Fuel SaFeTY gaSoline ModelS onlYEleCTriC MoTor SaFeTY eleCTriC ModelS onlY Power Cord/Cable SafetyEnvironMenTal SaFeTY ToWing SaFeTY„ alWaYS shutdown engine before transporting Tow Bar to Mixer Connection Safety chain connectionLbs kg SpecificationsDimensions DimensionsEngine Maintenance Hardware Power PlantsGeneral information ApplicationComponents Before Starting InspectionEngine Oil Check Fuel Check Controls Start/Stop SwitchesBelt Check Blade CheckInitial Servicing Basic engineAdjust paddles as shown in Figure Paddle blade adjustmentStart-up Turn the engine switch to the on positionBelt Slip Lever Start/Stop Position Mixing/Dumping OperationStopping the Mixer Page First Every Maintenance engineInstall drain bolt with sealing washer and tighten securely Engine air cleanerEngine oil Ball Socket and Clamp Face Maintenance Maintenance MixerDrum Head Seals Drum Bearing Bracket LubricationMain Gear and Drive Pinion Alignment Wheel BearingsGear Lubrication InspectTooth Contact between Main Gear and Drive PinionTires/Wheels/Lug Nuts Tires Wear/InflationStart all wheel lug nuts by hand Lug Nut Torque RequirementsNever use an pneumatic air gun to tighten wheel lug nuts Suspension Mixer CleaningMixer Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Drum difficult to discharge tilt Blades adjusted too tight Adjust if necessaryReplace seals Defective or worn drum supportWiring diagram Explanation of Code in Remarks Column Suggested Spare Parts Element, air cleaner GX160Belt Rope, recoil starter GX160Instructions DE Sécurité Nameplate and decalsDecal, safety instructions french Decal, safety instructions English 515275DECAL, handle kick back, safety grate Crush hazard EM948630 Decal, push to stop EnglishFrame assy 491692 514842530023 507444Engine END Paddle shaft assy492584 NUT, Lock 1/2 EM202896 514752492399 B0LT, 1/2 X EM200292 EM202898Steel tub assy 3249 530028C20561-001 491008Axle assy 8115 34693005 8164Engine assy EM905016 EM969013 NUT 3/8 NC G5 506488492378 Bolt 3/8 NC X 1-3/4 G5 490957 513868Cabinet assy EM505186 520620503723 491010FreigHT poliCY Terms and conditions of sale partsPage HERE’S HOW to GET Help

WM70SH8C, WM70SH5C specifications

The Multiquip WM70SH5C and WM70SH8C are cutting-edge water pump models designed for construction and industrial applications. These robust machines are specifically engineered to handle a variety of heavy-duty pumping tasks, making them an essential asset for contractors and industrial operators alike.

The WM70SH5C model is powered by a reliable 5.5 HP Honda engine, while the WM70SH8C variant features an 8 HP Honda engine, providing additional power for demanding applications. Both models are equipped with a high-performance centrifugal pump, ensuring efficient water transfer and quick operation. They are capable of moving large volumes of water, making them suitable for dewatering, irrigation, and other water management tasks.

One of the standout features of the WM70SH series is their impressive maximum flow rate. The pumps can deliver up to 2,000 gallons per minute, significantly reducing the time required for water removal in flooded areas or construction sites. This efficiency is crucial in maintaining project timelines and ensuring safety in work environments.

Durability is another key characteristic of these models. The WM70SH5C and WM70SH8C are built with heavy-duty materials, including a cast iron pump housing and aluminum alloy components, which resist corrosion and ensure a long operational lifespan. Additionally, their rugged construction allows them to withstand harsh working conditions, making them reliable even in the toughest environments.

Ease of use and maintenance is also a priority in the design of these pumps. The WM70SH series features an easy-access maintenance panel that simplifies routine checks and service procedures. The equipped oil alert system helps prevent engine damage by shutting down the engine if the oil level is too low, providing peace of mind for operators.

Both models are designed for portability, with integrated handles and a lightweight frame that facilitate easy transportation. This mobility makes the WM70SH series ideal for contractors who need to move equipment frequently from one job site to another.

In summary, the Multiquip WM70SH5C and WM70SH8C water pumps stand out in the market for their powerful performance, robust construction, and ease of use. They are designed to deliver efficiency, reliability, and durability, making them an excellent choice for any water pumping requirements in construction and industrial applications. With features catering to the demands of heavy-duty tasks, these pumps enhance productivity while ensuring operational safety.
Top Page Image Contents