Mabe Canada PCR06WATSS, PCR06BATSS installation instructions Reverse Door Swing

Page 11
Install Covers

Installation Instructions

2REVERSE DOOR SWING

SKIP THIS STEP IF DOOR SWING SUITS THE INSTALLATION

Parts Included:

Top left case hinge

Bottom left case hinge

Left and right side decorative hinge cover

Decorative hinge screw hole cover

Torx® driver bit

Tools Required:

Phillips screwdriver

Electric drill

To remove the door:

Flatten the shipping carton to use as a pad.

Remove the 2 screws and the toekick. Set aside the screws and toekick for final installation.

Use the supplied Torx® bit and electric drill to remove

the 3 screws holding the top case hinge. Lift off the hinge. (Screws will be used to install the new hinge.)

Lift the door off the bottom case hinge.

Remove the bottom case hinge pin and bracket.

To reinstall the door:

1.Remove the door stop and cam riser on the bottom right side of the door.

2.Remove the bottom fill plug on the bottom left side of the door.

3.Reinstall the original door stop and cam riser onto the bottom left side of the door.

4.Reinstall the bottom fill plug on the bottom right side of the door.

5.Remove the top fill plug on the top left side of the door.

6.Reinstall the top fill plug on the top right side.

7.Install the new supplied bottom case hinge pin and bracket onto bottom left side. Ensure plastic cam riser is on the case hinge pin.

8.Place the door onto the bottom case hinge.

9.Install the supplied left-hand top case hinge with the 3 original screws.

10.Select the hinge cover marked with an “L”.

11.Peel backing off the tape inside the decorative hinge cover.

12. Press and snap the hinge cover into place.

13. Snap the screw hole cover into place on the opposite side.

IMPORTANT: Check to be sure screws are tight and that the door is straight

and does not sag. The door should swing freely.

Install

3 Hinge

Screws

Remove

Top Hinge

Hinge

Pin and

Bracket

Door Stop

and Cam Riser

Remove

Hinge

Install Toekick

The toekick has a cutout on the left and right sides.

1. Remove the

 

 

plug on the

 

Move Fill

left side and

 

 

Plug to

reinstall on

Spacer

Right Side

the right side.

 

Standoff

 

 

 

2. Install original

screws and spacers.

Install screws through the spacer standoff, toekick and into the base as shown.

11

Image 11
Contents Troubleshooting Tips Operating Instructions InstallationEt d’installation Installation Instructions Manual delInstructions Care and CleaningOperating Instructions Tips Consumer SupportCare and Cleaning TroubleshootingConsumer Controls and features-Beverage CenterInstallation Instructions Tips SupportInserting Wine Bottles Controls and features-Wine ChillerSafety Loading Tips and Suggestions Troubleshooting TipsRemoving Full Extension Drawers Controls and features-Beverage Center and Wine ChillerSafety Interior Light and SwitchInstructions Operating Care and cleaningChoose the location When installed in a cornerProduct Clearances Read these instructions completely and carefullyCutout depth should be 24″ Installation SpaceSIDE-BY-SIDE Installations Additional SpecificationsStaining Wood Drawer Fronts Tools RequiredParts Supplied Grounding the Beverage Center and Wine ChillerReverse Door Swing Slide Product Into the Cutout Connect PowerSET Temperature Controls LevelFans come on in order to cool the appliance Normal operating soundsOperating Installation Instructions Before you call for service…Safety Instructions Ge.com Care and Cleaning Operating Instructions Safety Instructions Consumer Support Troubleshooting TipsGeneral Electric Company GE Service Protection PlusConsumer Product Ownership Registration Care Instructions InstallationSafety Instructions CleaningWhat Mabe Will Not Cover Mabe Will ReplaceConsommateur Soutien au Mode d’emploiLa section Française Agent de refroidissement ’entreposez pas ou n’installez pas l’appareil à l’extérieur’emploi Soutien au ConsommateurBranchement Électrique ’installation Instructions Conseils de dépannageConsommateur Commandes et caractéristiques-Refroidisseur de boissonsInstructions ’installation Vin rouge Vin blanc ’installation InstructionsService Chargement des bouteilles de vinPour remplacer Façades de tiroir en boisLumière intérieure et interrupteur Pour retirerEntretien et nettoyage ’installation InstructionsLisez attentivement et soigneusement ces instructions Si installé dans un coinChoix de l’emplacement Dégagement Requis Pour Ouverture DE PorteCaractéristiques supplémentaires Espace Pour InstallationInstallation Côte À Côte La dimension d’encastrement doit être de 61 cm 24 poDéballage Outils NécessairesPièces Fournies Teindre LES Façade EN Bois DES TiroirsInversion DU Battant DE Porte Branchement DE L’APPAREIL Mise À NiveauSons normaux de fonctionnement Entretien et nettoyage ’installation InstructionsLa porte est laissée ouverte Avant d’appeler le service de dépannage…Temps chaud ou ouvertures De porte fréquentesAppliquez une couche mince de paraffine ou de Conseils de dépannage Instructions d’installation Entretien et Nettoyage Mode d’emploi Consignes de SécuritéOwnership Registration Page Mode d’emploi Ce que GE ne couvre pas Pour la période de GE remplaceraPerte de vin à cause de la détérioration Défectueuse du système scellé de refroidissementVisitez notre site Web ou appelez-nous au Soutien au consommateur Service de réparationsProlongation de garantie 800.361.3400Soporte al consumidor Problemas SolucionarLa sección en Español Consejos para la soluciónNo almacene o instale este aparato en el exterior RefrigerantesAntes de desechar su antiguo refrigerador Guarde Estas Instrucciones Estantes de cristal Controles y funciones Centro de bebidasLimpieza Operación Control de temperaturaServir Controles y funciones Refrigerador de vinoInserción de botellas de vino AlmacenarPara quitar los cajones Cuidado y limpiezaQuitar los cajones de extensión completa Luz interior e interruptorCuidado y limpieza Elija la ubicación Tolerancias DEL ProductoLea estas instrucciones en su totalidad y con atención Cuando se instale en una esquinaLa profundidad de sección debe ser de 61 cm 24″ EL Espacio DE InstalaciónInstalaciones Conjuntas Una instalación conjunta requiere una apertura de alDestornillador Philips número Llave inglesa Herramientas NecesariasPartes Suministradas Quitar EL EmbalajeInvertir EL Sentido DE Apertura DE LA Puerta Definir Controles DE Temperatura NivelarConectar LA Alimentación Deslizar EL Producto Hacia EL HuecoWhoosh Sonidos de funcionamiento normalesCuidado y Antes de llamar para solicitar servicio técnico…Se crea humedad en Notas Notas Notas Partes defectuosas Garantía del centro de bebidas o refrigerador de vinoPor el período de GE reemplazará Lo que GE no cubriráLo que Mabe no cubrirá Por el período de Mabe reemplazaráEn Canadá geappliances.ca Soporte al consumidorU.S. ge.com Consumer SupportCanada, call

PCR06WATSS, PCR06BATSS specifications

Mabe Canada, renowned for its commitment to quality and innovation in home appliances, presents two of its standout refrigerator models: the PCR06BATSS and the PCR06WATSS. These units epitomize modern design, energy efficiency, and functionality, catering to the diverse needs of today’s households.

Both models feature a sleek and stylish appearance that blends seamlessly with any kitchen decor. The stainless steel finish of the PCR06BATSS adds a touch of sophistication, while the classic white of the PCR06WATSS provides a timeless and clean look. Their compact sizes make them perfect for smaller kitchens, apartments, or as secondary refrigerators in larger homes.

One of the main features shared by both the PCR06BATSS and PCR06WATSS is their spacious interior design. Equipped with adjustable shelves, these refrigerators offer flexible storage solutions that can easily accommodate various sizes and shapes of food items. The well-designed layout ensures that every inch of space is utilized efficiently, making it effortless to organize groceries and ingredients.

These models are powered by advanced cooling technologies that prioritize freshness. With their multi-air flow systems, both refrigerators circulate cold air evenly throughout the compartments, eliminating warm spots and maintaining optimum temperatures. This feature is essential for preserving the freshness of fruits, vegetables, and leftovers.

Additionally, Mabe has incorporated energy-efficient technologies in both models, which significantly reduce power consumption without compromising performance. This not only helps to lower electricity bills but also supports environmentally conscious practices, making them an attractive choice for eco-minded consumers.

The user-friendly interface is another important characteristic of the PCR06BATSS and PCR06WATSS. With easy-to-use controls and clear temperature settings, adjusting the cooling requirements becomes a breeze. Moreover, the interior LED lighting enhances visibility, allowing users to easily find items even in low light conditions.

In terms of capacity, both models provide ample storage without taking up extensive kitchen space. They are perfect for storing essentials for small families or individuals, making meal prep and storage more convenient.

In summary, the Mabe Canada PCR06BATSS and PCR06WATSS refrigerators offer a blend of style, efficiency, and functionality. With their innovative features, energy-saving technologies, and thoughtfully designed interiors, these models stand out as exceptional choices for those seeking reliable and aesthetically pleasing refrigeration solutions in their homes.