U-Line 2275ZWCOL Lightbulb Replacement, Leveling, Removing and Installing Grille, Maintenance

Page 14

6 Maintenance

Lightbulb Replacement

To replace the lightbulb in your U-Line unit:

1.Find the light located at the top of the unit. Grasp the edges of the light housing lens (1) opposite the exposed tab and gently push the lens toward the tab (2).

2.Pull the edge of the lens down (1) and swing it out of the light housing.

2

1

IMPORTANT

ALWAYS use a genuine U-Line replacement 120V 10 watt bulb (Part Number 31317) in the light housing. Use of any other bulb within the housing will produce excessive heat, causing damage to the light housing and cabinet interior, and will compromise the precise temperature control of the unit.

1.Replace the lens by first inserting the tab side back into the housing at a slight angle.

2.While gently pushing the lens towards the tab end, push the free end into the housing, and release when you hear a snap.

Leveling

IMPORTANT

Unit must be level, for proper door and ice maker (if equipped) operation.

1

5 5

For Models with adjustable leveling feet:

1.Use a level to check the levelness of the unit from front to back and from side to side. Place the level along top edge and side edge as shown (1).

2.If the unit is not level, rotate the adjustable leveling legs to raise or lower each corner of the unit (5) as necessary.

3.Check levelness after each adjustment and repeat the previous steps until the unit is level.

Removing and Installing Grille

WARNING

Disconnect electric power to the unit before removing the grille.

WARNING

DO NOT touch the condenser fins(4). The condenser fins are SHARP and can be easily damaged.

Removing the grille.

1.Disconnect power to the unit.

2.Remove control knob (6) if equipped.

3.Loosen the two screws (1). Some models may have only one screw in the center.

4.Remove grille (2) and grille cap (if equipped)(3) from unit.

Installing the grille:

1.For 15 and 29 models make sure grille cap (3) is behind grille in slots (2) provided in grille before attaching grille to unit.

2.For 75 models place the hook-hinge located on the rear bottom side of the grille (2) onto the front lip of the unit base. Swing the grille up into position.

3.Align cabinet and grill holes and secure, but do not overtighten grille screws (1).

4.Install control knob (6) if equipped.

5.Reconnect power to the unit.

1

2

45

Typical Model Shown

12

U-Line 22 Series Maintenance

Page 13 Page 15
Image 14
Page 13 Page 15
Contents USE and Care Guide Introduction Read and save this Use and Care GuidePlease Record Your Model Information Table of Contents Safety Precautions Safety Alert DefinitionsGeneral Precautions Line Use and Care Guide Dual Zone Product Features Wine Captain Dual Zone FeaturesWine Captain Dual Zone Additional Features For indoor use onlyInitial Startup Dual Temperature ZonesAir Flow Electronic Control PanelInterior Lighting Checking Product TemperatureTo check the actual product temperature in the unit Electronic Control Quick Guide TouchLine Wine Guide Looking Behind the LabelWine Selections Suggestions Red WinesIdeal Wine Storage Considerations Terminology DescriptionDo not remove the track rails from the cabinet Wine Rack Removal and InstallationWine Stocking Recommendation Wood Trim Finishing Staining and final finish applicationMaintenance Lightbulb ReplacementRemoving and Installing Grille Installing the grilleWine Rack Removal/Installation Line Use and Care Guide Door Reversability Door Alignment and AdjustmentTo align and adjust the door Reversing the doorReinstall Hole Plugs Reinstall hinge to bottom oppositeReinstall hinge to top opposite Prepare door for reinstallationCleaning Exterior CleaningInterior Cleaning DefrostingProduct Disposal Condensor CleaningStorage, Vacation and Moving Interval Every Six MonthsReplacement Parts Before Calling for ServiceIf Service is Required Troubleshooting GuideLine Use and Care Guide Line Corporation Limited Warranty LINE.COM
Top Page Image Contents