Taylor 430 TORQUE manual To the Operator

Page 8

Section 2

To the Operator

 

 

The freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The Taylor Model 430 Torque, when properly operated and cared for, will produce a consistent quality product. Like all mechanical products, they will require cleaning and maintenance. A minimum amount of care and attention is necessary if the operating procedures outlined in this manual are followed closely.

This Operator’s Manual should be read before operating or performing any maintenance on your equipment.

Your Taylor freezer will NOT eventually compensate for and correct any errors during the set--up or filling operations. Thus, the initial assembly and priming procedures are of extreme importance. It is strongly recommended that personnel responsible for the equipment’s operation, both assembly and disassembly, sit down together and go through these procedures in order to be properly trained and to make sure that no misunderstandings exist.

In the event you should require technical assistance, please contact your local authorized Taylor Distributor.

Note: Warranty is valid only if the parts are authorized Taylor parts, purchased from an authorized Taylor Distributor, and the required service work is provided by an authorized Taylor service technician. Taylor reserves the right to deny warranty claims on equipment or parts if non--approved parts or refrigerant were installed in the machine, system modifications were performed beyond factory recommendations, or it is determined that the failure was caused by neglect or abuse.

Note: Constant research results in steady improvements; therefore, information in this manual is subject to change without notice.

If the crossed out wheeled bin symbol is affixed to this product, it signifies that this product is compliant with the EU Directive as well as other similar legislation in effect after August 13, 2005. Therefore, it must be collected separately after its use is completed, and cannot be disposed as unsorted municipal waste.

The user is responsible for returning the product to the appropriate collection facility, as specified by your local code.

For additional information regarding applicable local laws, please contact the municipal facility and/or local distributor.

Compressor Warranty Disclaimer

The refrigeration compressor(s) on this machine are warranted for the term indicated on the warranty card accompanying this machine. However, due to the Montreal Protocol and the U.S. Clean Air Act Amendments of 1990, many new refrigerants are being tested and developed, thus seeking their way into the service industry. Some of these new refrigerants are being advertised as drop--in replacements for numerous applications. It should be noted that, in the event of ordinary service to this machine’s refrigeration system, only the refrigerant specified on the affixed data label should be used. The unauthorized use of alternate refrigerants will void your compressor warranty. It will be the owner’s responsibility to make this fact known to any technician he employs.

It should also be noted that Taylor does not warrant the refrigerant used in its equipment. For example, if the refrigerant is lost during the course of ordinary service to this machine, Taylor has no obligation to either supply or provide its replacement either at billable or unbillable terms. Taylor does have the obligation to recommend a suitable replacement if the original refrigerant is banned, obsoleted, or no longer available during the five year warranty of the compressor.

Taylor will continue to monitor the industry and test new alternates as they are being developed. Should a new alternate prove, through our testing, that it would be accepted as a drop--in replacement, then the above disclaimer would become null and void. To find out the current status of an alternate refrigerant as it relates to your compressor warranty, call the local Taylor Distributor or the Taylor Factory. Be prepared to provide the Model/Serial Number of the unit in question.

061012

 

 

To the Operator

4

Model 430 Torque

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Shake/Slush Freezer Information found on data plate Table of Contents Table of Contents Site Preparation Installer SafetySection Air Cooled Units Electrical ConnectionsBeater Rotation RefrigerantTo the Operator Section Safety Model 430 Torque Safety090114 Safety Model 430 Torque Operator Parts Identification Description Part Number111018 Operator Parts Identification Model 430 Torque Description Part Number Section Important To the Operator Section Operating Procedures AssemblyOperating Procedures Model 430 Torque Step Sanitizing Priming Rinsing Closing ProcedureDraining Product From The Freezing Cylinder Brush Cleaning CleaningDisassembly Regular Maintenance Checks Important Operator ChecklistDuring Cleaning and Sanitizing Winter Storage Section Troubleshooting Guide Problem Probable Cause RemedyModel 430 Torque Troubleshooting Guide Parts Replacement Schedule Section Parts List Description Part QTY Warr Remarks Parts Number Class UpdateDescription Part QTY Warr Remarks Parts Draw Valve Probe A.-MIX OUT-SQUARE Hole 043027HABK 208-230V 60HZ 1PH Torque W/PURGE Port Door 043012HACO 115V 60HZ 1PH Flavor Burst Ready 043012H210 115V 60HZ 1PH Panel SPIN-RIGHT SIDE-HARD Slush PANEL-BACK *430 MAN-OPER 430 Dunkin Donut Model 430 Torque Model 430 Torque

430 TORQUE specifications

The Taylor 430 TORQUE is a powerful and versatile machine designed for professional landscapers and agricultural operators looking to enhance their productivity and efficiency. Known for its robust construction and advanced technologies, the 430 TORQUE has made a name for itself in the industry, providing exceptional performance in various applications.

One of the standout features of the Taylor 430 TORQUE is its impressive engine capacity. Equipped with a high-performance engine, this machine delivers consistent torque and power, enabling operators to tackle even the toughest jobs with ease. The engine is designed for durability and longevity, ensuring that it can withstand the rigors of regular use in demanding environments.

In terms of design, the 430 TORQUE boasts a compact and lightweight profile, which increases its maneuverability. This makes it ideal for working in tight spaces and navigating around obstacles, allowing operators to achieve a greater level of precision in their work. The machine’s advanced hydraulic system provides smooth operation and responsive controls, further enhancing its performance and user experience.

One of the key technologies integrated into the Taylor 430 TORQUE is its intelligent control system. This system allows operators to monitor and adjust various parameters in real-time, optimizing performance according to specific job requirements. Features such as automatic speed adjustment and load sensing technology enable the machine to operate efficiently, reducing fuel consumption and minimizing wear and tear on the engine.

The 430 TORQUE is also equipped with a range of attachments, making it a versatile solution for different tasks. Whether it’s mowing, tilling, or excavating, operators can easily switch between attachments to suit their needs. This adaptability saves time and increases efficiency, making the machine a valuable asset for any landscaping or agricultural operation.

In terms of safety, the Taylor 430 TORQUE is designed with various protective features such as an ergonomic operator seat, safety guards, and emergency stop controls. These features ensure that operators can work with confidence and peace of mind, knowing that safety is a priority.

In summary, the Taylor 430 TORQUE stands out in the marketplace due to its exceptional power, advanced technologies, and versatile design. It is an invaluable tool for professionals in the landscaping and agricultural sectors, proving to be efficient, reliable, and user-friendly for a variety of tasks. With the Taylor 430 TORQUE, operators can expect to achieve excellent results while minimizing downtime and maximizing productivity.
Top Page Image Contents