Taylor Essential Maintenance and 430 Parts for Optimal Performance
Page 21

Cleaning

Step 1

Prepare a pail of an approved 100 PPM cleaning solution (examples: 2--1/2 gal. [9.5 liters] of Kay--5Ror 2 gal. [7.6 liters] of Stera--SheenR). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS.

Step 2

Pour the cleaning solution into the hopper and allow it to flow into the freezing cylinder.

Step 3

While the solution is flowing into the freezing cylinder, brush--clean the mix hopper and mix inlet hole.

Step 4

Place the power switch in the “WASH” position. This will agitate the cleaning solution in the freezing cylinder.

Step 5

Place an empty pail beneath the door spout and move the draw handle to the right. Draw off all the cleaning solution. When the solution stops flowing from the door spout, move the draw handle to the left, and place the power switch in the “OFF” position.

Disassembly

Step 1

BE SURE THE CONTROL SWITCH IS IN THE “OFF” POSITION.

Step 2

Remove the handscrews, freezer door, beater assembly, torque rotor, scraper blade and drive shaft from the freezing cylinder. Take these parts to the sink for cleaning.

Step 3

Remove the front drip tray and the splash shield. Take these parts to the sink for cleaning.

Step 4

Remove the rear drip pan from the front panel. Note: If the drip pan is filled with an excessive amount of mix, it is an indication the drive shaft seal should be replaced or properly lubricated.

Brush Cleaning

Step 1

Prepare a sink with a cleaning solution (examples: Kay--5Ror Stera--SheenR). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFI- CATIONS. (If another approved cleaner is used, dilute according to label instructions. IMPORTANT: Follow the label directions. Too STRONG of a solution can cause parts damage, while too MILD of a solution will not provide adequate cleaning.) Make sure all brushes provided with the freezer are available for brush cleaning.

Step 2

Remove the o--ring and seal from the drive shaft. Remove the o--ring and the bearing from the torque rotor.

Step 3

Remove the draw valve, ice buster, front bearing, and gasket from the freezer door. Remove all o--rings.

Note: To remove the o--ring, use a single service towel to grasp the o--ring. Apply pressure in an upward direction until the o--ring pops out of its groove. With the other hand, push the top of the o--ring forward until it rolls out of the groove and can be removed easily.

Step 4

Thoroughly brush--clean all disassembled parts in the cleaning solution, making sure all lubricant and mix film is removed. Place all the cleaned parts on a clean, dry surface to air dry.

Step 5

Return to the freezer with a small amount of cleaning solution. Brush--clean the rear shell bearing at the back of the freezing cylinder with the black bristle

brush.

Figure 28

Step 6

Wipe clean all exterior surfaces of the freezer.

090114

Model 430 Torque

17

Operating Procedures

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Shake/Slush Freezer Information found on data plate Table of Contents Table of Contents Installer Safety SectionSite Preparation Electrical Connections Air Cooled UnitsRefrigerant Beater RotationTo the Operator Model 430 Torque Safety Section Safety090114 Safety Model 430 Torque Description Part Number Operator Parts Identification111018 Operator Parts Identification Model 430 Torque Description Part Number Section Important To the Operator Assembly Section Operating ProceduresOperating Procedures Model 430 Torque Step Sanitizing Priming Closing Procedure Draining Product From The Freezing CylinderRinsing Cleaning DisassemblyBrush Cleaning Important Operator Checklist During Cleaning and SanitizingRegular Maintenance Checks Winter Storage Problem Probable Cause Remedy Section Troubleshooting GuideModel 430 Torque Troubleshooting Guide Parts Replacement Schedule Description Part QTY Warr Remarks Parts Number Class Update Section Parts ListDescription Part QTY Warr Remarks Parts Draw Valve Probe A.-MIX OUT-SQUARE Hole 043027HABK 208-230V 60HZ 1PH Torque W/PURGE Port Door 043012HACO 115V 60HZ 1PH Flavor Burst Ready 043012H210 115V 60HZ 1PH Panel SPIN-RIGHT SIDE-HARD Slush PANEL-BACK *430 MAN-OPER 430 Dunkin Donut Model 430 Torque Model 430 Torque

430 TORQUE specifications

The Taylor 430 TORQUE is a powerful and versatile machine designed for professional landscapers and agricultural operators looking to enhance their productivity and efficiency. Known for its robust construction and advanced technologies, the 430 TORQUE has made a name for itself in the industry, providing exceptional performance in various applications.

One of the standout features of the Taylor 430 TORQUE is its impressive engine capacity. Equipped with a high-performance engine, this machine delivers consistent torque and power, enabling operators to tackle even the toughest jobs with ease. The engine is designed for durability and longevity, ensuring that it can withstand the rigors of regular use in demanding environments.

In terms of design, the 430 TORQUE boasts a compact and lightweight profile, which increases its maneuverability. This makes it ideal for working in tight spaces and navigating around obstacles, allowing operators to achieve a greater level of precision in their work. The machine’s advanced hydraulic system provides smooth operation and responsive controls, further enhancing its performance and user experience.

One of the key technologies integrated into the Taylor 430 TORQUE is its intelligent control system. This system allows operators to monitor and adjust various parameters in real-time, optimizing performance according to specific job requirements. Features such as automatic speed adjustment and load sensing technology enable the machine to operate efficiently, reducing fuel consumption and minimizing wear and tear on the engine.

The 430 TORQUE is also equipped with a range of attachments, making it a versatile solution for different tasks. Whether it’s mowing, tilling, or excavating, operators can easily switch between attachments to suit their needs. This adaptability saves time and increases efficiency, making the machine a valuable asset for any landscaping or agricultural operation.

In terms of safety, the Taylor 430 TORQUE is designed with various protective features such as an ergonomic operator seat, safety guards, and emergency stop controls. These features ensure that operators can work with confidence and peace of mind, knowing that safety is a priority.

In summary, the Taylor 430 TORQUE stands out in the marketplace due to its exceptional power, advanced technologies, and versatile design. It is an invaluable tool for professionals in the landscaping and agricultural sectors, proving to be efficient, reliable, and user-friendly for a variety of tasks. With the Taylor 430 TORQUE, operators can expect to achieve excellent results while minimizing downtime and maximizing productivity.
Top Page Image Contents