Taylor 430 TORQUE manual Important Operator Checklist, During Cleaning and Sanitizing

Page 22

Section 7 Important: Operator Checklist

During Cleaning and Sanitizing:

ALWAYS FOLLOW LOCAL HEALTH CODES

Cleaning and sanitizing schedules are governed by federal, state, or local regulatory agencies, and must be followed accordingly. If the unit has a “Standby mode”, it must not be used in lieu of proper cleaning and sanitizing procedures and frequencies set forth by the ruling health authority. The following check points should be stressed during the cleaning and sanitizing operations.

the rerun with fresh mix in a ratio of 50/50 during the day’s operation.

j6. On a designated day of the week, run the mix as low as feasible and discard after closing. This will break the rerun cycle and reduce the possibility of high bacteria and coliform counts.

j7. Properly prepare the cleaning and sanitizing solutions. Read and follow label directions carefully. Too strong of a solution may damage the parts and too weak of a solution will not do an adequate job of cleaning or sanitizing.

j8. Temperature of mix in mix hopper and walk--in cooler should be below 40_F. (4.4_C.).

CLEANING AND SANITIZING MUST BE PERFORMED DAILY.

Regular Maintenance Checks:

j 1. Replace scraper blades that are nicked, damaged or worn down. Before installing beater, be certain the scraper blade is properly attached.

Troubleshooting Bacterial Count:

j

2. Check rear shell bearing for signs of wear

 

j 1. Thoroughly clean and sanitize machine

 

(excessive mix leakage in drip pan) and be

 

certain it is properly cleaned.

regularly, including complete disassembly and

 

 

 

 

brush cleaning.

j

3. Using a screwdriver and cloth towel, keep the

 

j 2. Use all brushes supplied for thorough cleaning.

 

rear shell bearing and the female square drive

 

socket clean and free of lubricant and mix

The brushes are specially designed to reach all

 

 

deposits.

mix passageways.

 

 

 

 

j 3. Use the white bristle brush to clean the mix feed

j 4. Dispose of o--rings and seals if they are worn,

 

torn, or fit too loosely, and replace with new

tube, which extends from the hopper down to

 

ones.

the rear of the freezing cylinder.

 

 

 

j 4. Use the black bristle brush to thoroughly clean

j 5. Follow all lubricating procedures as outlined in

 

“Assembly”.

the rear shell bearing located at the rear of the

 

 

 

freezing cylinder. Be sure to have a generous

j 6. Check the condenser(s) for accumulation of dirt

amount of cleaning solution on the brush.

 

and lint. Dirty condensers will reduce the

 

 

efficiency and capacity of the machine.

j 5. IF LOCAL HEALTH CODES PERMIT THE

 

Condensers should be cleaned monthly with a

USE OF RERUN, make sure the mix rerun is

 

soft brush. Never use screwdrivers or other

stored in a sanitized, covered stainless steel

 

metal probes to clean between the fins.

container and used the following day. DO NOT

 

Note: For machines equipped with an air filter,

prime the machine with rerun. When using

 

it will be necessary to vacuum clean the filters

rerun, skim off the foam and discard, then mix

 

on a monthly schedule.

071205

 

 

 

 

 

 

 

Important: Operator Checklist

18

Model 430 Torque

 

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Shake/Slush Freezer Information found on data plate Table of Contents Table of Contents Section Installer SafetySite Preparation Air Cooled Units Electrical ConnectionsBeater Rotation RefrigerantTo the Operator Section Safety Model 430 Torque Safety090114 Safety Model 430 Torque Operator Parts Identification Description Part Number111018 Operator Parts Identification Model 430 Torque Description Part Number Section Important To the Operator Section Operating Procedures AssemblyOperating Procedures Model 430 Torque Step Sanitizing Priming Draining Product From The Freezing Cylinder Closing ProcedureRinsing Disassembly CleaningBrush Cleaning During Cleaning and Sanitizing Important Operator ChecklistRegular Maintenance Checks Winter Storage Section Troubleshooting Guide Problem Probable Cause RemedyModel 430 Torque Troubleshooting Guide Parts Replacement Schedule Section Parts List Description Part QTY Warr Remarks Parts Number Class UpdateDescription Part QTY Warr Remarks Parts Draw Valve Probe A.-MIX OUT-SQUARE Hole 043027HABK 208-230V 60HZ 1PH Torque W/PURGE Port Door 043012HACO 115V 60HZ 1PH Flavor Burst Ready 043012H210 115V 60HZ 1PH Panel SPIN-RIGHT SIDE-HARD Slush PANEL-BACK *430 MAN-OPER 430 Dunkin Donut Model 430 Torque Model 430 Torque

430 TORQUE specifications

The Taylor 430 TORQUE is a powerful and versatile machine designed for professional landscapers and agricultural operators looking to enhance their productivity and efficiency. Known for its robust construction and advanced technologies, the 430 TORQUE has made a name for itself in the industry, providing exceptional performance in various applications.

One of the standout features of the Taylor 430 TORQUE is its impressive engine capacity. Equipped with a high-performance engine, this machine delivers consistent torque and power, enabling operators to tackle even the toughest jobs with ease. The engine is designed for durability and longevity, ensuring that it can withstand the rigors of regular use in demanding environments.

In terms of design, the 430 TORQUE boasts a compact and lightweight profile, which increases its maneuverability. This makes it ideal for working in tight spaces and navigating around obstacles, allowing operators to achieve a greater level of precision in their work. The machine’s advanced hydraulic system provides smooth operation and responsive controls, further enhancing its performance and user experience.

One of the key technologies integrated into the Taylor 430 TORQUE is its intelligent control system. This system allows operators to monitor and adjust various parameters in real-time, optimizing performance according to specific job requirements. Features such as automatic speed adjustment and load sensing technology enable the machine to operate efficiently, reducing fuel consumption and minimizing wear and tear on the engine.

The 430 TORQUE is also equipped with a range of attachments, making it a versatile solution for different tasks. Whether it’s mowing, tilling, or excavating, operators can easily switch between attachments to suit their needs. This adaptability saves time and increases efficiency, making the machine a valuable asset for any landscaping or agricultural operation.

In terms of safety, the Taylor 430 TORQUE is designed with various protective features such as an ergonomic operator seat, safety guards, and emergency stop controls. These features ensure that operators can work with confidence and peace of mind, knowing that safety is a priority.

In summary, the Taylor 430 TORQUE stands out in the marketplace due to its exceptional power, advanced technologies, and versatile design. It is an invaluable tool for professionals in the landscaping and agricultural sectors, proving to be efficient, reliable, and user-friendly for a variety of tasks. With the Taylor 430 TORQUE, operators can expect to achieve excellent results while minimizing downtime and maximizing productivity.
Top Page Image Contents