Manuals / Genie / Household Appliance / Garage Door Opener

Genie manual Homelink and Car2U compatible, Model 1022/1024, 1.800.354.3643

Models: 1024

1 28

Download 28 pages 45.26 Kb

Page 1

Image 1

Model 1022/1024

Includes Remote Control

(Up to 7 Single Button Programmable Controls Available)Safety Beam System must be installed to close door.

For use only with sectional doors. Your Residential Operator comes with a Rail Assembly which is standard for up to a 7 foot high door.

Homelink® and Car2U™ compatible

For Answers and Assistance:

1.800.354.3643

or visit www.geniecompany.com

SAVE THIS MANUAL FOR FUTURE REFERENCE

Homelink® is a registered trademark of Johnson Controls Technology Company.

Car2U™ is a trademark of Lear Corporation.

PN# 3642036212, 8/09/2007

Page 1

Image 1

Genie manual Homelink and Car2U compatible, Model 1022/1024, 1.800.354.3643, Includes Remote Control

Contents

Includes Remote Control Homelink and Car2U compatibleSafety Beam System must be installed to close door Model 1022/1024MOVING DOOR SAFETY INFORMATIONELECTRICAL SHOCK HIGH SPRING TENSIONOPERATOR FEATURES TABLE OF CONTENTSSAFETY FEATURES Operator MUST be installed with the included Wall ControlDO NOT USE AN EXTENSION CORD DO NOT USE ALTERNATE POWER SUPPLIESNOTE Mounting brackets must be installed within code specifications NOTE This operator is designed for use with SECTIONAL doors only TYPICAL SECTIONAL DOOR INSTALLATIONPOWER CORD APPROX. 45 IN TO 120V GROUNDED OUTLET EXTENSION SPRING OR SAFETY BEAMSPARTS IDENTIFICATION - Not Shown Full Size RECOMMENDED TOOLSFASTENERS - Shown Full size See Parts List below for full description IMPORTANT! - Information needed when callingDO NOT RETURN TO POINT OF PURCHASE Model number - located on packaging3-PIECE RAIL HARDWARE ASSEMBLED VIEW 1-PIECE RAIL HARDWARE ASSEMBLED VIEWIMPORTANT INSTALLATION INSTRUCTIONS 1 OPERATOR ASSEMBLYRAIL ASSEMBLY Use a clean, flat surface WARNING Toreduce the risk of severe injury or deathNOTE For power head and rail assembly locate Bag 1 from Box POWER HEAD & RAIL ASSEMBLYNOTE For split rail clamps, nuts, and bolts locate Bag 0 from Box NOTE Handle carefully! Drive chain can slide out of railHEADER AND DOOR MOUNTING BRACKETS 2 INSTALLATION1. Finding header bracket mounting location Fig. 2-1, cANGLE IRON ON FINISHED CEILING MOUNTING THE OPERATORUNFINISHED OR OPEN BEAM Extra framingDOOR BRACKET INSTALL DOOR ARMSshort clevis pin & cotter pin bolts as far2a. Wiring If pre-wired 3 WALL CONTROL INSTALLATION2b. Wiring If NOT pre-wired 1. Wall Control locationDo NOT install rear cover yet 3.Securely fasten wires4. Mounting 2. Mounting Safety Beam Source Red LED and Sensor Green LED 4 SAFETY BEAM SYSTEM INSTALLATION3a. Wiring If NOT pre-wired as you go Fig. 4-6 on next page4. Split and strip ends of sensor wires Fig 3b. Wiring pre-wired5. Attach Safety Beam wire to power head wire terminal 6 5 4 3 2WITH PERMANENT WIRING 5 CONNECTING TO POWERWITH POWER SUPPLIED WITH GROUNDED PLUGENGAGE CHAIN TO CARRIAGE 6 DOOR LIMITSCLOSE TRAVEL LIMIT OPEN TRAVEL LIMITUP/DOWN FORCE CARRIAGE LOCKERASE - OPEN/CLOSE TRAVEL LIMIT CONTACT REVERSE TESTFCC and IC CERTIFIED 7 PROGRAMMING REMOTE CONTROLSLOST OR STOLEN REMOTE NOTE For remote control locate Box1. Battery replacement 9 LIGHT BULB/LENS INSTALLATION2. Visor clip NOTE For lens cover locate BoxROUTINE MONTHLY MAINTENANCE 10 MAINTENANCE3. Safety Beam System CONTACT A TRAINED PROFESSIONAL SERVICE TECHNICIANCIRCUIT WIRING DIAGRAM POWER CORDCORDON DE SECTEUR CABLE ELÉCTRICO Remove power from operator prior to removing coverPROBLEM TROUBLESHOOTING GUIDE - OPERATIONCheck power source If not, check fuse or circuit breaker If power is OKPossible Problem TROUBLESHOOTING GUIDE - POWER HEAD LEDSolution Power head LEDPN# 3642036212, 8/09/2007 TRANSMITTER COMPLIANCE STATEMENTBE AVAILABLE IF YOU EVER NEED TO CALL US The Genie Company Professional Access Systems LIMITED WARRANTYDate Purchased MO / D / YR Serial Number WK / YR / PI Operator Model Remote Control Model Store Purchased Store Address