Atlas Sound CP700 specifications Rear Panel Description

CP700 COMMERCIAL POWER AMPLIFIER

4. Limit LED Indicator

OWNER'S MANUAL

The CP700 comes equipped with limiter circuitry and LEDs to indicate when this circuitry is activated. The limiter circuitry engages only when the input signals reach a specifi c, factory set magnitude. Once this limit has been reached, the circuitry will reduce the input level enough to prevent clipping at the speaker output terminals.

REAR PANEL DESCRIPTION

10	CP700		CH-18, 4, and 2 Ohms			AUDIO TRANSFORMER CH-1
			D I R . O U T P U T +		-	0	70		100 I S O L . O U T P U T
	Commercial
	Power
	Amplifier
	Output Power
	400 W / 4 Ohms	+				-	+	-	+
	350 W / 70.7 V			BRIDGE		70V			25V
				MONO		-	100V		+
			CH-28, 4, and 2 Ohms			AUDIO TRANSFORMER CH-2
			D I R . O U T P U T +		-	0	70		100 I S O L . O U T P U T
	AC100V-50/60Hz
	AC120V-50/60Hz
	AC230V-50/60Hz
	AC240V-50/60Hz
			-			-	+	-	+
						70V			25V
				BRIDGE
				MONO		-	100V		+
	POWER
										MADE IN CHINA
		CAUTION							CAUTION
								RISK OF ELECTRIC SHOCK
	TO REDUCE THE RISK OF ELECTRIC SHOCK								DO NOT OPEN
								AVIS RISQUE DE CHOC ELECTRIQUE
	DO NOT REMOVE COVER (OR BACK)
	NO USER SERVICEABLE PARTS INSIDE									NE PAS OUVRIR
	REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

11

6

IN																IN
					AMPLIFIER INPUTS
						CH-2	CH-1
						+ - GND	- +
THRU		22	18	16	1					22	18	16	1			THRU
	6				41				6				41
					1									1
	2				2			2					2
32						0	2							0
0						8	30								8
4						6	4								6
6						4	6							2	4
5					0		5						0
	0								0
GND		0-	LEVEL							0-	LEVEL
										STEREO
							PARALLEL								BRIDGE

1601 Jack McKay Blvd., Ennis, TX 75119

(800) 876-3333 AtlasSound.com

9

8

7

5

Figure 2

5.Gain Controls

One stepped attenuator per channel increases or decreases the sensitivity of the CP700 2dB per step. Maximum voltage gain of the CP700 is 32dB.

6.CH1/CH2 Inputs (XLR Connectors)

Two female XLR inputs (one per channel) are provided. These inputs are balanced and confi gured as follows: pin 1 ground, pin 2 plus, pin 3 minus. The XLR connections are typically used in portable audio systems where quick connect and disconnect is warranted.

7.Balanced Barrier Strip Inputs

Balanced inputs are provided on this barrier strip for permanent installation applications. The use of the appropriate spade type lug is highly recommended for best connection integrity and a neat, professional appearance.

8.CH1/CH2 Loop Through

Two male XLR (one per channel) are provided for looping the input signals to other CP700s or similar devices. These connectors are wired in parallel with the female XLR inputs, pin for pin.

Specifications are subject to change without notice

AtlasSound.com

1601 JACK MCKAY BOULEVARD ENNIS, TEXAS 75119 U.S.A. •		TELEPHONE: (800) 876-3333 •	FAX: (800) 765-3435
©2005 ATLAS SOUND LP	Printed in U.S.A.	ATS002102 RevC 9/05	PP

5