True Manufacturing Company T-35 Electrical Instructions, Sealing Cabinet to Floor

Page 12

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

ELECTRICAL INSTRUCTIONS

A.Before your new unit is connected to a power supply, check the incoming voltage with a voltmeter. If anything less than 100% of the rated voltage for operation is noted, correct immediately.

B.All units are equipped with a 7 ft. (2.1m) service cord, and must be powered at proper operating voltage at all times. Refer to cabinet data plate for this voltage.

True requires that a sole use circuit be dedicated for the unit. Failure to do so voids warranty.

WARNING

Compressor warranties are void if compressor burns out due to low voltage.

WARNING

Power supply cord ground should not be removed!

NOTE

To reference wiring diagram - Remove front louvered grill, wiring diagram is positioned on the inside cabinet wall.

SEALING CABINET TO FLOOR

Step 1 - Position Cabinet

Allow one inch between the wall and rear of the refrigerator to assure proper ventilation. For freezers 3 inches between the wall and rear of the cabinet will assure proper ventilation.

Step 2 - Level Cabinet

Cabinet should be level, side to side and front to back. Place a carpenter’s level in the interior floor in four places:

A. Position level in the inside floor of the unit near the doors. (Level should be parallel to cabinet front). Level cabinet.

B. Position level at the inside rear of cabinet. (Again level should be placed parallel to cabinet back).

C. Perform similar procedures to steps a & b by placing the level on inside floor (left and right sides - parallel to the depth of the cooler). Level cabinet.

Step 3

Draw an outline on the base on the floor.

Step 4

Raise and block the front side of the cabinet.

Step 5

Apply a bead of “NSF Approved Sealant”, (see list

below), To floor on half inch inside the outline drawn. The bead must be heavy enough to seal the entire cabinet surface when it is down on the sealant.

Step 6

Raise and block the rear of the cabinet

Step 7

Apply sealant on floor as outline in Step 5. on other three sides.

Step 8

Examine to see that cabinet is sealed to floor around entire perimeter.

Note:

Asphalt floors are very susceptible to chemical attack. A layer of tape on the floor prior to applying the sealant will protect the floor.

NSF Approved Sealants:

1.Minnesota Mining #ECU800 Caulk

2.Minnesota Mining #ECU2185 Caulk

3.Minnesota Mining #ECU1055 Bead

4.Minnesota Mining #ECU1202 Bead

5.Armstrong Cork - Rubber Caulk

6.Products Research Co. #5000 Rubber Caulk

7.G.E. Silicone Sealer

8.Dow Corning Silicone Sealer

10

www.truemfg.com

10

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Series Freezer / Refrigerator Swing Slide Door True Food Service Equipment, Inc Safety Precautions Safety Information Proper Disposal of the Freezer / Refrigerator USE of Extension CordsBefore You Throw Away Your Old Refrigerator or Freezer Refrigerant DisposalHOW to Connect Electricity North America Use OnlyInstallation / Operation Instructions Ownership Required ToolsUncrating Locating LevelingRemote Units This section applies to remotes only Securing Castors and Legs Unit levelingInstalling Optional Castors on a T-12FG Final LocationConductors and Circuits Electrical Instructions Sealing Cabinet to FloorReplacement Parts StartupRecommendation Shelving Installation / Operation & Light Switch Location Shelf & Organizer InstallationWire Shelves Light Switch LocationFreezers Defrost Time Clock Operation Grasslin Timer If the Compressor will Not RUNIf the Motor Compressor Starts but TripsDefrost Time Clock Light Cover Installation for T-12FG MAINTENANCE, Care & Cleaning Cleaning the Condenser Coil Required ToolsImportant Warranty Information Temperature Control Adjustment for High Altitude only Danfoss Temperature Control High Altitude OnlyStainless Steel Equipment Care and Cleaning Light Bulb Replacement IDL Integrated Door LightingInterior Lights IDL Integrated Door LightingA. Warranty Information U.S.A & Canada only

T-35 specifications

True Manufacturing Company has long been synonymous with excellence in refrigeration equipment, and the T-35 model is no exception. This commercial refrigeration unit exemplifies the company's commitment to design, durability, and user-friendly features, making it a top choice for restaurants, cafes, and other foodservice operations.

The True T-35 is a powerful and highly efficient one-section refrigerator that features a spacious interior, ideal for holding a significant quantity of perishable items. This reach-in refrigerator is built with a stainless-steel exterior, ensuring not only a sleek appearance but also durability against the rigors of any commercial kitchen environment. The interior is comprised of aluminum, which provides easy cleaning and maintenance, ensuring adherence to health and safety standards.

One of the standout features of the T-35 is its advanced refrigeration system. It is equipped with a factory-balanced refrigeration system that utilizes environmentally friendly refrigerant, enhancing energy efficiency while providing excellent temperature control. The unit maintains temperatures ranging from 33°F to 38°F, crucial for preserving the freshness of perishable items.

In addition to its robust cooling capabilities, the T-35 incorporates a self-contained capillary tube system that delivers superior cooling performance even in high-demand situations. The evaporator fan motor runs continuously to ensure optimal air circulation, promoting uniform temperatures throughout the interior.

The True T-35 is designed with user comfort in mind. It comes with a set of adjustable, heavy-duty PVC-coated wire shelves, which allow operators to customize the layout based on their specific storage needs. The ergonomic door handles are easy to grip and open, making access to stored items seamless during busy service periods.

For energy efficiency, the T-35 includes features such as LED interior lighting, which not only enhances visibility but also reduces overall energy consumption. The unit is also designed to operate quietly, allowing it to fit seamlessly into any environment without causing disturbances.

Overall, the True Manufacturing Company T-35 combines functionality and efficiency in a beautifully designed package. Its advanced cooling technology, flexible storage options, and durable construction make it an indispensable asset for any foodservice operation, ensuring that food items remain fresh and safe for consumption. With a solid warranty and dedicated customer support, the T-35 represents the high standard of quality and reliability that True Manufacturing is renowned for.
Top Page Image Contents