Whirlpool W10325493A Installation Requirements, Tools and Parts, Location Requirements

Page 3

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

■Level

■³⁄₈" drive ratchet

■Tape measure

■Flat-blade screwdriver

■Phillips screwdriver

■Hand or electric drill

■Wrench or pliers

■7 mm combination wrench

■Pipe wrench

■¹⁄₈" (3.2 mm) drill bit (for wood floors)

■³⁄₁₆" (4.8 mm) carbide-tipped masonry drill bit (for concrete/ ceramic floors)

■Pipe-joint compound resistant to LP gas

■Noncorrosive leak-detection solution

Parts supplied

Check that all parts are included.

A

B

C

A.Anti-tip bracket

B.Plastic anchors (2)

C.#10 x 1" screws (2)

■Anti-tip bracket must be securely mounted to subfloor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store.

Parts needed

Check local codes and consult gas supplier. Check existing gas supply. See “Gas Supply Requirements” section.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

■It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the oven frame behind the left side of the broiler door.

A

■The range should be located for convenient use in the kitchen.

■Recessed installations must provide complete enclosure of the sides and rear of the range.

■To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

■All openings in the wall or floor where range is to be installed must be sealed.

■Do not seal the range to the side cabinets.

■Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

■The floor anti-tip bracket must be installed. To install the anti- tip bracket shipped with the range, see “Install Anti-Tip Bracket” section.

■Grounded electrical supply is required. See “Electrical Requirements” section. Proper gas supply connection must be available. See “Gas Supply Requirements” section.

■Contact a qualified floor covering installer to check that the floor covering can withstand at least 200°F (93°C).

■Use an insulated pad or ¼" (0.64 cm) plywood under range if installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194° (90°C).

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Table of Contents/Table des matières Your safety and the safety of others are very important Range SafetyInstallation Requirements Tools and PartsLocation Requirements Mobile home installations require Mobile Home Additional Installation RequirementsProduct Dimensions Freestanding Range Installation ClearancesGas Supply Requirements Line pressure testing at ½ psi gauge 14 WCP or lower Installation InstructionsInstall Anti-Tip Bracket Line pressure testing above ½ psi gauge 14 WCPMake Gas Connection Typical flexible connection Verify Anti-Tip Bracket LocationLevel Range Typical rigid pipe connectionTo Light Standing Pilot Lights If the low flame needs adjustingCheck Operation Check Operation of Oven/Broil BurnerToo much air of flame should occur Complete InstallationIf the flame needs adjusting If you need Assistance or ServiceTurn manual shutoff valve to the closed position GAS ConversionsLP Gas Conversion To Convert Gas Pressure RegulatorTo Convert Oven Burner To Convert Surface BurnersSet the front panel aside and locate the oven thermostat Pilot and Bypass Screws ConversionComplete Conversion Natural Gas ConversionInstall Natural gas orifice spuds in the valves Pilot and Bypass Screws Conversion Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreExigences D’INSTALLATION Exigences d’emplacementOutillage et composants Distances de dégagement à respecter Dimensions du produit Cuisinière autoportanteConversion pour lalimentation au propane Spécifications de l’alimentation en gazType de gaz Gaz naturelTests de pressurisation de la canalisation de gaz Canalisation dalimentation en gazDétendeur Débit thermique des brûleursFixer le gabarit avec du ruban adhésif Instructions D’INSTALLATIONInstallation de la bride antibasculement Déballage de la cuisinièreRaccordement au gaz Achever le raccordement Vérification de lemplacement de la bride AntibasculementRaccordement typique à une canalisation rigide Raccordement typique par raccord flexibleRéglage de laplomb de la cuisinière Contrôle du fonctionnementPour allumer les témoins de veilleuse Ouvrir la porte du gril Remettre en place le bouton de commandeContrôle du fonctionnement du four Brûleur du gril Si la flamme basse doit être régléeSi la cuisinière ne fonctionne pas, contrôler ce qui suit Achever l’installationSi vous avez besoin d’assistance ou de service Si la flamme doit être régléePlacer le robinet d’arrêt manuel à la position fermée Conversions Pour Changement DE GAZConversion pour lalimentation au propane Conversion du détendeurConversion des brûleurs de surface Conversion du brûleur du fourImportant Ne pas serrer excessivement Terminer la conversion Conversion des veilleuses et des vis de DérivationConversion au gaz naturel Conversion du brûleur du four Terminer la conversion

W10325493A specifications

The Whirlpool W10325493A is a high-performance appliance that brings efficiency and convenience to modern kitchens. As a part of Whirlpool's commitment to innovative technology, this model embodies a range of features designed to enhance cooking experiences.

One of the standout features of the W10325493A is its advanced cooking technology. It includes a powerful convection system that ensures even heat distribution around meals, promoting uniform cooking and browning. This is particularly beneficial when roasting or baking large items, as it reduces cooking time and ensures that every inch of food is perfectly treated.

In addition to its convection feature, the W10325493A also boasts a user-friendly touch control panel. This panel allows users to easily select desired cooking modes, temperatures, and times with just a few taps. The intuitive interface makes it accessible for all skill levels, from novice cooks to seasoned chefs. Furthermore, its digital display provides clear visibility of cooking settings, helping users keep track of their culinary tasks.

Another remarkable characteristic of the W10325493A is its spacious interior. With ample cooking space, this appliance accommodates large dishes without compromise. Whether preparing a family feast or entertaining guests, the generous capacity makes it easier to manage multiple items simultaneously. This versatility is complemented by adjustable racks that provide flexibility in organizing cooking trays and pans.

Energy efficiency is another critical feature of the W10325493A. With its eco-friendly design and energy-saving modes, this appliance minimizes energy consumption without sacrificing performance. This not only reduces utility bills but also reflects a commitment to environmental sustainability.

The W10325493A also integrates smart technology capabilities. With Wi-Fi connectivity, users can monitor and control the appliance remotely via a smartphone app. This feature allows for setting timers, adjusting temperature settings, and even receiving notifications when dishes are ready, making it a convenient addition to any busy household.

Lastly, the sleek and modern exterior of the W10325493A complements any kitchen aesthetic. Its stainless-steel finish is not only visually appealing but also easy to maintain, ensuring it looks great for years to come.

In summary, the Whirlpool W10325493A is a multifaceted appliance that combines advanced cooking technology, user-friendly features, energy efficiency, and smart connectivity, making it an excellent choice for enhancing culinary experiences in any home.
Top Page Image Contents