Whirlpool W10325493A Verify Anti-Tip Bracket Location, Level Range, Typical rigid pipe connection

Page 8

Typical rigid pipe connection

A combination of pipe fittings must be used to connect the range to the existing gas line. Your connections may be different; according to the supply line type, size and location.

1.Apply pipe-joint compound made for use with LP gas to all pipe thread connections.

2.Using a pipe wrench to tighten, connect the gas supply to the range.

B

C

A

D

E

 

 

 

F

 

G

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A. Pressure regulator

D. Union

connection fitting

E. Nipple

B. 90° elbow

F. Manual shutoff valve

C. Black iron pipe

G. ½" or ¾" gas pipe

Typical flexible connection

1.Use a combination wrench and pliers to attach the flexible connector to the adapters. Check that connector is not kinked.

A

 

B

 

D

C

 

E

F

 

G

H

 

A. Pressure regulator

E. Adapter

connection fitting

F. Use pipe-joint

B. Use pipe-joint compound.

compound.

C. Adapter

G. Manual shutoff valve

D. Flexible connector

H. ½" or ¾" gas pipe

Complete Connection

1.Open the manual shutoff valve in the gas supply line. The valve is open when the handle is parallel to the gas pipe.

A

B

A. Closed valve

B. Open valve

2.Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leak found.

3.Push back on side support rods and slowly lower the cooktop until it snaps into place.

4.Place burners, burner caps and grates on the cooktop.

Verify Anti-Tip Bracket Location

1.Check that the anti-tip bracket is installed:

Look for the anti-tip bracket securely attached to the floor.

Slide the range back so the rear range foot is under the anti-tip bracket.

Level Range

1.Place rack in oven.

2.Place level on rack and check levelness of range, first side to side; then front to back.

3.If range is not level, pull range forward until rear leveling leg is removed from the anti-tip bracket. Use ³⁄₈" drive ratchet and wrench or pliers to adjust leveling legs up or down until range is level.

4.Push range back into position.

5.Check that rear leveling leg is engaged in anti-tip bracket.

NOTE: Range must be level for satisfactory baking performance.

8

Image 8
Contents Table of Contents/Table des matières Range Safety Your safety and the safety of others are very importantLocation Requirements Installation RequirementsTools and Parts Mobile Home Additional Installation Requirements Product Dimensions Freestanding RangeInstallation Clearances Mobile home installations requireGas Supply Requirements Installation Instructions Install Anti-Tip BracketLine pressure testing above ½ psi gauge 14 WCP Line pressure testing at ½ psi gauge 14 WCP or lowerMake Gas Connection Verify Anti-Tip Bracket Location Level RangeTypical rigid pipe connection Typical flexible connectionIf the low flame needs adjusting Check OperationCheck Operation of Oven/Broil Burner To Light Standing Pilot LightsComplete Installation If the flame needs adjustingIf you need Assistance or Service Too much air of flame should occurGAS Conversions LP Gas ConversionTo Convert Gas Pressure Regulator Turn manual shutoff valve to the closed positionTo Convert Surface Burners To Convert Oven BurnerPilot and Bypass Screws Conversion Complete ConversionNatural Gas Conversion Set the front panel aside and locate the oven thermostatInstall Natural gas orifice spuds in the valves Pilot and Bypass Screws Conversion Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importanteOutillage et composants Exigences D’INSTALLATIONExigences d’emplacement Dimensions du produit Cuisinière autoportante Distances de dégagement à respecterSpécifications de l’alimentation en gaz Type de gazGaz naturel Conversion pour lalimentation au propaneCanalisation dalimentation en gaz DétendeurDébit thermique des brûleurs Tests de pressurisation de la canalisation de gazInstructions D’INSTALLATION Installation de la bride antibasculementDéballage de la cuisinière Fixer le gabarit avec du ruban adhésifRaccordement au gaz Vérification de lemplacement de la bride Antibasculement Raccordement typique à une canalisation rigideRaccordement typique par raccord flexible Achever le raccordementPour allumer les témoins de veilleuse Réglage de laplomb de la cuisinièreContrôle du fonctionnement Remettre en place le bouton de commande Contrôle du fonctionnement du four Brûleur du grilSi la flamme basse doit être réglée Ouvrir la porte du grilAchever l’installation Si vous avez besoin d’assistance ou de serviceSi la flamme doit être réglée Si la cuisinière ne fonctionne pas, contrôler ce qui suitConversions Pour Changement DE GAZ Conversion pour lalimentation au propaneConversion du détendeur Placer le robinet d’arrêt manuel à la position ferméeImportant Ne pas serrer excessivement Conversion des brûleurs de surfaceConversion du brûleur du four Conversion des veilleuses et des vis de Dérivation Terminer la conversionConversion au gaz naturel Conversion du brûleur du four Terminer la conversion

W10325493A specifications

The Whirlpool W10325493A is a high-performance appliance that brings efficiency and convenience to modern kitchens. As a part of Whirlpool's commitment to innovative technology, this model embodies a range of features designed to enhance cooking experiences.

One of the standout features of the W10325493A is its advanced cooking technology. It includes a powerful convection system that ensures even heat distribution around meals, promoting uniform cooking and browning. This is particularly beneficial when roasting or baking large items, as it reduces cooking time and ensures that every inch of food is perfectly treated.

In addition to its convection feature, the W10325493A also boasts a user-friendly touch control panel. This panel allows users to easily select desired cooking modes, temperatures, and times with just a few taps. The intuitive interface makes it accessible for all skill levels, from novice cooks to seasoned chefs. Furthermore, its digital display provides clear visibility of cooking settings, helping users keep track of their culinary tasks.

Another remarkable characteristic of the W10325493A is its spacious interior. With ample cooking space, this appliance accommodates large dishes without compromise. Whether preparing a family feast or entertaining guests, the generous capacity makes it easier to manage multiple items simultaneously. This versatility is complemented by adjustable racks that provide flexibility in organizing cooking trays and pans.

Energy efficiency is another critical feature of the W10325493A. With its eco-friendly design and energy-saving modes, this appliance minimizes energy consumption without sacrificing performance. This not only reduces utility bills but also reflects a commitment to environmental sustainability.

The W10325493A also integrates smart technology capabilities. With Wi-Fi connectivity, users can monitor and control the appliance remotely via a smartphone app. This feature allows for setting timers, adjusting temperature settings, and even receiving notifications when dishes are ready, making it a convenient addition to any busy household.

Lastly, the sleek and modern exterior of the W10325493A complements any kitchen aesthetic. Its stainless-steel finish is not only visually appealing but also easy to maintain, ensuring it looks great for years to come.

In summary, the Whirlpool W10325493A is a multifaceted appliance that combines advanced cooking technology, user-friendly features, energy efficiency, and smart connectivity, making it an excellent choice for enhancing culinary experiences in any home.