Whirlpool W10325493A Check Operation of Oven/Broil Burner, To Light Standing Pilot Lights

Page 9

Check Operation

To Light Standing Pilot Lights:

Before using the range, the standing pilots must be lit. They will stay lit after turning off the burners.

1.Make sure all controls are off and the oven and cooktop are cool.

2.Remove surface grates from the cooktop.

3.Lift the cooktop by both front corners until the side support rods snap into position.

A

A. Side support rods

4.Using a match, light both burner pilot lights.

5.The surface pilot flames should be 0.4" to 0.6" (1.0 to 1.5 cm) high.

A

A. 0.4" - 0.6" (1.0 - 1.5 cm)

6.If the pilot flame needs adjustment, use a flat-blade screwdriver and turn the adjusting screw until the flame is of the desired height.

A

A. Adjusting screw

7.Push back on the side support rods and slowly lower the cooktop until it snaps into position.

8.Push in and turn each surface burner control knob to the “HI” position. The flame should light with 4 seconds.

9.If surface burners do not ignite, repeat steps 3 to 6.

10.Check each cooktop burner for proper flame. The small inner cone should have a very distinct blue flame ¼" (0.64 cm) to ½" (1.3 cm) long. The outer cone is not as distinct as the inner cone.

A

B

A. Outer cone

B. Inner cone

11.Turn the control knob quickly to the “LO” position after the burner lights. If the flame goes out, turn the control knob to the “OFF” position.

12.Check each cooktop burner for proper low flame. The low flame should be a minimum, steady blue flame. The flame size should be ¼" to ³⁄₈" (0.64 cm to 0.95 cm) high.

If the low flame needs adjusting:

1.Turn control knob to the “Lo” setting and remove control knob.

2.Insert a small flat-blade screwdriver into the valve stem. Turn the valve adjusting screw to obtain the smallest flame that will not go out when the control of a cold burner is quickly turned from “HI” to “Lo.” Turn right to decrease flame height. Turn left to increase flame height. Repeat for other cooktop burners as needed.

A

A. Valve stem

3.Replace control knob.

Check Operation of Oven/Broil Burner

1.Make sure all controls are off and the oven is cool.

2.Open the oven door to remove oven racks and the oven bottom tray.

3.Remove the fasteners holding the flame spreader. Lift and pull out the flame spreader.

A

A

B

C

A. Oven bottom tray

B.Fasteners

C.Flame spreader

4.Locate the pilot light on the left-hand side of the oven burner.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Table of Contents/Table des matières Your safety and the safety of others are very important Range SafetyInstallation Requirements Tools and PartsLocation Requirements Product Dimensions Freestanding Range Mobile Home Additional Installation RequirementsInstallation Clearances Mobile home installations requireGas Supply Requirements Install Anti-Tip Bracket Installation InstructionsLine pressure testing above ½ psi gauge 14 WCP Line pressure testing at ½ psi gauge 14 WCP or lowerMake Gas Connection Level Range Verify Anti-Tip Bracket LocationTypical rigid pipe connection Typical flexible connectionCheck Operation If the low flame needs adjustingCheck Operation of Oven/Broil Burner To Light Standing Pilot LightsIf the flame needs adjusting Complete InstallationIf you need Assistance or Service Too much air of flame should occurLP Gas Conversion GAS ConversionsTo Convert Gas Pressure Regulator Turn manual shutoff valve to the closed positionTo Convert Oven Burner To Convert Surface BurnersComplete Conversion Pilot and Bypass Screws ConversionNatural Gas Conversion Set the front panel aside and locate the oven thermostatInstall Natural gas orifice spuds in the valves Pilot and Bypass Screws Conversion Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreExigences D’INSTALLATION Exigences d’emplacementOutillage et composants Distances de dégagement à respecter Dimensions du produit Cuisinière autoportanteType de gaz Spécifications de l’alimentation en gazGaz naturel Conversion pour lalimentation au propaneDétendeur Canalisation dalimentation en gazDébit thermique des brûleurs Tests de pressurisation de la canalisation de gazInstallation de la bride antibasculement Instructions D’INSTALLATIONDéballage de la cuisinière Fixer le gabarit avec du ruban adhésifRaccordement au gaz Raccordement typique à une canalisation rigide Vérification de lemplacement de la bride AntibasculementRaccordement typique par raccord flexible Achever le raccordementRéglage de laplomb de la cuisinière Contrôle du fonctionnementPour allumer les témoins de veilleuse Contrôle du fonctionnement du four Brûleur du gril Remettre en place le bouton de commandeSi la flamme basse doit être réglée Ouvrir la porte du grilSi vous avez besoin d’assistance ou de service Achever l’installationSi la flamme doit être réglée Si la cuisinière ne fonctionne pas, contrôler ce qui suitConversion pour lalimentation au propane Conversions Pour Changement DE GAZConversion du détendeur Placer le robinet d’arrêt manuel à la position ferméeConversion des brûleurs de surface Conversion du brûleur du fourImportant Ne pas serrer excessivement Terminer la conversion Conversion des veilleuses et des vis de DérivationConversion au gaz naturel Conversion du brûleur du four Terminer la conversion

W10325493A specifications

The Whirlpool W10325493A is a high-performance appliance that brings efficiency and convenience to modern kitchens. As a part of Whirlpool's commitment to innovative technology, this model embodies a range of features designed to enhance cooking experiences.

One of the standout features of the W10325493A is its advanced cooking technology. It includes a powerful convection system that ensures even heat distribution around meals, promoting uniform cooking and browning. This is particularly beneficial when roasting or baking large items, as it reduces cooking time and ensures that every inch of food is perfectly treated.

In addition to its convection feature, the W10325493A also boasts a user-friendly touch control panel. This panel allows users to easily select desired cooking modes, temperatures, and times with just a few taps. The intuitive interface makes it accessible for all skill levels, from novice cooks to seasoned chefs. Furthermore, its digital display provides clear visibility of cooking settings, helping users keep track of their culinary tasks.

Another remarkable characteristic of the W10325493A is its spacious interior. With ample cooking space, this appliance accommodates large dishes without compromise. Whether preparing a family feast or entertaining guests, the generous capacity makes it easier to manage multiple items simultaneously. This versatility is complemented by adjustable racks that provide flexibility in organizing cooking trays and pans.

Energy efficiency is another critical feature of the W10325493A. With its eco-friendly design and energy-saving modes, this appliance minimizes energy consumption without sacrificing performance. This not only reduces utility bills but also reflects a commitment to environmental sustainability.

The W10325493A also integrates smart technology capabilities. With Wi-Fi connectivity, users can monitor and control the appliance remotely via a smartphone app. This feature allows for setting timers, adjusting temperature settings, and even receiving notifications when dishes are ready, making it a convenient addition to any busy household.

Lastly, the sleek and modern exterior of the W10325493A complements any kitchen aesthetic. Its stainless-steel finish is not only visually appealing but also easy to maintain, ensuring it looks great for years to come.

In summary, the Whirlpool W10325493A is a multifaceted appliance that combines advanced cooking technology, user-friendly features, energy efficiency, and smart connectivity, making it an excellent choice for enhancing culinary experiences in any home.
Top Page Image Contents