Whirlpool W10325493A Installation Instructions, Unpack Range, Install Anti-Tip Bracket

Page 6

Line pressure testing above ½ psi gauge (14" WCP)

The range and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ psi (3.5 kPa).

Line pressure testing at ½ psi gauge (14" WCP) or lower

The range must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psi (3.5 kPa).

INSTALLATION INSTRUCTIONS

Unpack Range

WARNING

Excessive Weight Hazard

Use two or more people to move and install range. Failure to do so can result in back or other injury.

1.Do not use oven door handle to lift or move the range

2.Remove shipping materials, tape and film from range. Keep cardboard bottom under range.

3.Remove oven racks and parts package from inside oven.

4.To place range on its back, take 4 cardboard corners from the carton. Stack one cardboard corner on top of another. Repeat with the other 2 corners. Place them lengthwise on the floor behind the range to support the range when it is laid on its back.

5.Using 2 or more people, firmly grasp the range and gently lay it on its back on the cardboard corners.

6.Pull cardboard bottom firmly to remove.

7.Use an adjustable wrench to loosen the leveling legs. Adjust the leveling legs to the correct height. Leveling legs can be loosened to add up to a maximum of 1" (2.5 cm). A minimum of ³⁄₁₆" (0.5 cm) is needed to engage the anti-tip bracket.

NOTE: If height adjustment is made when range is standing, tilt the range back to adjust the front legs, then tilt forward to adjust the rear legs.

8.Place cardboard or hardboard in front of range. Using 2 or more people, stand range back up onto cardboard or hardboard.

Install Anti-Tip Bracket

Contact a qualified floor covering installer for the best procedure for drilling mounting holes through your type of floor covering.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

Before moving range, slide range onto shipping base, cardboard or hardboard.

1.Remove template from the anti-tip bracket kit (found inside the oven cavity) or from the back of this manual.

2.Place template on the floor in cabinet opening so that the left edge is against cabinet and top edge is against rear wall, molding or cabinet.

3.Tape template into place.

4.If countertop is not flush with cabinet opening edge, align template with overhang.

If cabinet opening is wider than that specified in the “Location Requirements” section, adjust template so range will be centered in cabinet opening.

5.To mount anti-tip bracket to wood floor, drill two ¹⁄₈" (3.2 mm) holes at the positions marked on the bracket template. Remove template from floor.

To mount anti-tip bracket to concrete or ceramic floor, use a ³⁄₁₆" (0.48 cm) masonry drill bit to drill 2 holes at the positions marked on the bracket template. Remove template from floor.

6.Tap plastic anchors into holes with a hammer.

7.Align anti-tip bracket holes with holes in floor. Fasten anti-tip bracket with screws provided.

Depending on the thickness of your flooring, longer screws may be necessary to anchor the bracket to the subfloor. Longer screws are available from your local hardware store.

8.Move range close enough to opening to allow for final gas connection. Remove shipping base, cardboard or hardboard from under range.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Table of Contents/Table des matières Range Safety Your safety and the safety of others are very importantInstallation Requirements Tools and PartsLocation Requirements Installation Clearances Mobile Home Additional Installation RequirementsProduct Dimensions Freestanding Range Mobile home installations requireGas Supply Requirements Line pressure testing above ½ psi gauge 14 WCP Installation InstructionsInstall Anti-Tip Bracket Line pressure testing at ½ psi gauge 14 WCP or lowerMake Gas Connection Typical rigid pipe connection Verify Anti-Tip Bracket LocationLevel Range Typical flexible connectionCheck Operation of Oven/Broil Burner If the low flame needs adjustingCheck Operation To Light Standing Pilot LightsIf you need Assistance or Service Complete InstallationIf the flame needs adjusting Too much air of flame should occurTo Convert Gas Pressure Regulator GAS ConversionsLP Gas Conversion Turn manual shutoff valve to the closed positionTo Convert Surface Burners To Convert Oven BurnerNatural Gas Conversion Pilot and Bypass Screws ConversionComplete Conversion Set the front panel aside and locate the oven thermostatInstall Natural gas orifice spuds in the valves Pilot and Bypass Screws Conversion Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importanteExigences D’INSTALLATION Exigences d’emplacementOutillage et composants Dimensions du produit Cuisinière autoportante Distances de dégagement à respecterGaz naturel Spécifications de l’alimentation en gazType de gaz Conversion pour lalimentation au propaneDébit thermique des brûleurs Canalisation dalimentation en gazDétendeur Tests de pressurisation de la canalisation de gazDéballage de la cuisinière Instructions D’INSTALLATIONInstallation de la bride antibasculement Fixer le gabarit avec du ruban adhésifRaccordement au gaz Raccordement typique par raccord flexible Vérification de lemplacement de la bride AntibasculementRaccordement typique à une canalisation rigide Achever le raccordementRéglage de laplomb de la cuisinière Contrôle du fonctionnementPour allumer les témoins de veilleuse Si la flamme basse doit être réglée Remettre en place le bouton de commandeContrôle du fonctionnement du four Brûleur du gril Ouvrir la porte du grilSi la flamme doit être réglée Achever l’installationSi vous avez besoin d’assistance ou de service Si la cuisinière ne fonctionne pas, contrôler ce qui suitConversion du détendeur Conversions Pour Changement DE GAZConversion pour lalimentation au propane Placer le robinet d’arrêt manuel à la position ferméeConversion des brûleurs de surface Conversion du brûleur du fourImportant Ne pas serrer excessivement Conversion des veilleuses et des vis de Dérivation Terminer la conversionConversion au gaz naturel Conversion du brûleur du four Terminer la conversion

W10325493A specifications

The Whirlpool W10325493A is a high-performance appliance that brings efficiency and convenience to modern kitchens. As a part of Whirlpool's commitment to innovative technology, this model embodies a range of features designed to enhance cooking experiences.

One of the standout features of the W10325493A is its advanced cooking technology. It includes a powerful convection system that ensures even heat distribution around meals, promoting uniform cooking and browning. This is particularly beneficial when roasting or baking large items, as it reduces cooking time and ensures that every inch of food is perfectly treated.

In addition to its convection feature, the W10325493A also boasts a user-friendly touch control panel. This panel allows users to easily select desired cooking modes, temperatures, and times with just a few taps. The intuitive interface makes it accessible for all skill levels, from novice cooks to seasoned chefs. Furthermore, its digital display provides clear visibility of cooking settings, helping users keep track of their culinary tasks.

Another remarkable characteristic of the W10325493A is its spacious interior. With ample cooking space, this appliance accommodates large dishes without compromise. Whether preparing a family feast or entertaining guests, the generous capacity makes it easier to manage multiple items simultaneously. This versatility is complemented by adjustable racks that provide flexibility in organizing cooking trays and pans.

Energy efficiency is another critical feature of the W10325493A. With its eco-friendly design and energy-saving modes, this appliance minimizes energy consumption without sacrificing performance. This not only reduces utility bills but also reflects a commitment to environmental sustainability.

The W10325493A also integrates smart technology capabilities. With Wi-Fi connectivity, users can monitor and control the appliance remotely via a smartphone app. This feature allows for setting timers, adjusting temperature settings, and even receiving notifications when dishes are ready, making it a convenient addition to any busy household.

Lastly, the sleek and modern exterior of the W10325493A complements any kitchen aesthetic. Its stainless-steel finish is not only visually appealing but also easy to maintain, ensuring it looks great for years to come.

In summary, the Whirlpool W10325493A is a multifaceted appliance that combines advanced cooking technology, user-friendly features, energy efficiency, and smart connectivity, making it an excellent choice for enhancing culinary experiences in any home.
Top Page Image Contents