Cornelius FlavorFusion Series Dispenser Troubleshooting Symptom Cause Remedy

Page 14

FlavorFusion Installation Manual

TROUBLESHOOTING

IMPORTANT: Only qualified personnel should service internal components or electrical wiring.

WARNING: If repairs are to be made to a product system, remove quick disconnects from the applicable product tank, then relieve the system pressure before proceeding. If repairs are to be made to the CO2 system, stop dispensing, shut off the CO2 supply, then relieve the system pressure before proceeding. If repairs are to be made to the refrigeration system, make sure electrical power is disconnected from the unit.

Should your unit fail to operate properly, check that there is power to the unit and that the hopper contains ice. If the unit does not dispense, check the following chart under the appropriate symptoms to aid in locating the defect.

Dispenser Troubleshooting

Symptom

Cause

 

Remedy

 

 

 

Blown fuse or circuit

Short circuit in electrical wiring

Repair Wiring

breaker

 

 

 

 

 

 

 

Inoperable agitator motor (shorted

Replace gear motor

 

motor)

 

 

 

 

 

 

 

 

 

 

Agitator does not

No power

 

Restore power or plug in unit

turn

 

 

 

 

 

 

 

Improperly installed upper ice chute

Check the upper ice chute assembly for

 

assembly (Reed switch is not being

proper assembly and operation

 

activated)

 

 

 

 

 

 

 

Inoperable reed switch

 

Replace reed switch

 

 

 

 

Electrical board driver circuit is

Replace main control board

 

defective

 

 

 

 

 

 

Gear motor has open circuit

Replace gear motor

 

 

 

 

Reed switch is not activated Improper

Check to make sure tongue of upper

 

assembly of upper ice chute to lower

chute engages into the back of the

 

chute.

 

lower chute, ensure upper chute

 

 

 

engages outside the lower chute, and

 

 

 

snap front of chute into place.

 

 

 

 

Broken wire in the 2-wire harness

Repair of replace 2-wire harness

 

leading to the reed switch

 

 

 

 

 

 

Bad connection at main control board,

Repair connection or replace 2-wire

 

J3, pins 2 &3

 

harness

 

 

 

 

 

 

Ice dispenses

Ice gate mechanism is stuck in open

Inspect gasket for proper position.

continuously

position

 

Examine gate plate to see if it slides

 

 

 

freely behind the lower ice chute.

 

 

 

 

Stuck or bent ice lever (does not allow

Examine ice dispense lever to see if it is

 

gate to close and open reed switch)

bent.

 

 

 

 

 

 

 

 

Slushy ice or water

Blocked drains in cold plate

 

Remove access covers in cold plate

in hopper

 

 

cover & inspect/clean drains

 

 

 

 

Poor ice quality due to water quality or

Correct water quality or repair ice maker

 

ice maker problems

 

 

 

 

 

 

 

 

 

Publication Number: 621057601INS

- 14 -

© 2005-2006, IMI Cornelius Inc.

Image 14
Contents Specification DescriptionSafety Tips Read and Follow all Safety InstructionsRecognize Safety Alerts Safety InstructionsCounter Mounting InstallationLEG Option Unit Operation Gate Restrictor Plate and Adjustment Gate Restrictor PlateDispense Type 1, Carbonated water dispense Solid LED Programming Mode Flashing SequencesProgramming Mode OFFSetting Water Flow Rate Valve with Flow AdjustersSetting a Button to Dispense Carbonated Water Only Adjusting Syrup/Water Ratio BrixSetting a Button to Dispense Non-carbonated Water Only Timed Dispense ProcedureMounting Template FlavorFusion Mounting TemplateDrip Tray Drain Assembly Drip Tray Drain AssemblyFlow Diagram DiagramsWiring Diagram BonusnoWiring Schematic XFRMR2Troubleshooting Dispenser Troubleshooting Symptom Cause RemedyFlavorFusion Installation Manual Carbonator Troubleshooting Symptom Cause RemedyDiagnostics Guide for the Main Control Board = OFFDiagnostics Guide for Flavorfusion Keypad Lighting PCB

FlavorFusion Series specifications

The Cornelius FlavorFusion Series is a groundbreaking advancement in beverage dispensing technology, expertly designed for businesses looking to enhance their drink offerings. This versatile series is tailored for high-volume establishments like restaurants, cafes, and convenience stores, providing an efficient and innovative solution for mixed beverages.

One of the main features of the FlavorFusion Series is its ability to create custom flavor profiles. Equipped with multiple flavor cartridges, the system allows users to blend various flavors, delivering a unique drinking experience. This modular design empowers users to adapt their beverage menu easily, experimenting with seasonal or trending flavors to attract customers.

The FlavorFusion Series utilizes cutting-edge technologies to ensure high-quality dispensing. The advanced mixing technology employed in the system accurately proportionates flavors, guaranteeing consistent taste with every pour. This precision is crucial for maintaining customer satisfaction, as patrons expect the same delightful experience regardless of when or where they order their beverages.

Another standout characteristic is the intuitive user interface, which simplifies operation for staff. The touch-screen control panel enables quick access to a range of beverage options and customization features. Staff can easily switch between different flavor profiles, and the system even allows for pre-programmed recipes, ensuring that even new employees can serve drinks accurately without extensive training.

Hygiene and maintenance are paramount in beverage service, and Cornelius addresses these concerns with the FlavorFusion Series. The system's self-cleaning capabilities reduce the need for frequent manual cleaning, while also ensuring that cross-contamination between flavors is minimized. With easy disassembly features, businesses can conduct thorough clean-ups between service hours without hassle.

Moreover, energy efficiency is a design principle integrated into the FlavorFusion Series. The system is designed to consume less power without compromising performance, making it a sustainable choice for eco-conscious businesses. This focus on energy savings not only helps reduce operational costs but also aligns with the growing demand for environmentally friendly practices in the food and beverage industry.

In summary, the Cornelius FlavorFusion Series represents the future of beverage dispensing, combining innovative flavor customization, advanced technology, ease of use, and sustainability. Businesses that invest in this system can look forward to attracting more customers with an enticing variety of drinks while ensuring operational efficiency and maintaining high standards of hygiene.