Aiwa CSD-FD92 Precautions, Explanation of Graphical Symbols, OWNER’S Record, Installation

Page 2

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

“CAUTION:TO REDUCE THE RISK OF

ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.”

Explanation of Graphical Symbols:

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

OWNER’S RECORD

For your convenience, record the model number (you will find it at the bottom of the unit) and serial number (you will find it in the battery compartment) in the space provided below. Please refer to them when you contact your AIWA dealer in case of difficulty.

Model No.

Serial No.

Precautions

Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating Instructions for future reference. All warnings and cautions in the Operating Instructions and on the unit should be strictly followed, as well as the safety suggestions below.

Installation

1Water and moisture - Do not use this unit near water, such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, swimming pool, or the like.

2Heat - Do not use this unit near sources of heat, including heating vents, stoves, or other appliances that generate heat.

It also should not be placed in temperatures less than 5°C (41°F) or greater than 35°C (95°F).

3Mounting surface - Place the unit on a flat, even surface.

4Ventilation - The unit should be situated with adequate space around it so that proper heat ventilation is assured.

Allow 10 cm (4 in.) clearance from the rear and the top of the unit and 5 cm (2 in.) from each side.

-Do not place the unit on a bed, rug, or similar surface that may block the ventilation openings.

-Do not install the unit in a bookcase, cabinet, or airtight rack where ventilation may be impeded.

5Objects and liquid entry - Take care that objects or liquids do not get inside the unit through the ventilation openings.

6Carts and stands - When placed or mounted on a stand or cart, the unit

should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit or cart to overturn or fall.

7Condensation - Moisture may form on the CD pickup lens when:

-The unit is moved from a cold spot to a warm spot

-The heating system has just been turned on

-The unit is used in a very humid room

-The unit is cooled by an air conditioner

When this unit has condensation inside, it may not function normally. Should this occur, leave the unit for a few hours, then try to operate again.

8Wall or ceiling mounting - The unit should not be mounted on a wall or ceiling, unless specified in the Operating Instructions.

Electric Power

1 Power sources - Use on batteries or AC house current, as specified in the Operating Instructions and marked on the unit.

2 Polarization - As a safety feature, some units are equipped with polarized AC power plugs which can only be inserted one way into a power outlet. If it is difficult or impossible to insert the AC power plug into an outlet, turn the plug over and try again. If it still does not easily insert into the outlet, please call a qualified service technician to service or replace

2ENGLISH

Image 2
Contents CSD-FD92 CSD-FD82 Installation PrecautionsExplanation of Graphical Symbols Electric PowerSpecifications CopyrightDemo display Power supplyConnect the AC cord as illustrated below Changing the display colorRemote control MaintenancePress *TUNER/BAND repeatedly to select the desired band Press r, t Tuning -, + to select a stationTuner Operation REPEAT/MODE/SLEEPPresetting Stations Sound AdjustmentPress CD Press dPLAY/DIR/PRESET cPLAY Preset to start playCD Operation Stop mode, press *REPEAT/MODE REPEAT, Random PlayProgrammed Play Repeat to program other tracks Press dc to start playRecording Tape OperationPlayback Setting the Sleep Timer