Creda S230G General, Ventilation, Final Installation, List of Loose Items

Page 27

INSTALLATION

1. GENERAL

The appliance is designed for mounting at a safe level into an oven housing which must be secured to the backing wall.

2.VENTILATION

a.The oven housing unit cabinet dimensions must comply with fig. 4.

b.An air gap of 30mm minimum must be provided at the rear of any top or bottom cupboards or shelves (see fig. 1).

c.It is necessary that the cabinets are provided with unobstructed ventilation, i.e. from adjacent cabinetry. This can be done by either raising the base of the cabinets using the adjusting feet (or spacers) or alternatively by providing a slot in the cabinet plinth to the dimensions in fig. 1.

d.The air gap at rear allows the warmed air to pass out of the inner cabinet space. Where it is intended to fit cupboards above the oven unit to ceiling height, it is essential that the warmed air is exhausted through the front of the cabinet (see fig. 1).

e.If an oven unit is installed adjacent to a tall cabinet, steam escaping from the oven when the door is opened could condense on and maybe stain the adjacent surface. To prevent permanent staining, the adjacent surface should be made of a material that is heat resisting and easy to clean. Adjacent tall cabinets should not be deeper than the oven housing cabinet.

3.FINAL INSTALLATION

a.Using a spirit level, check that the housing cabinet is level from side to side and from front to back in its installed position.

b.Correct any unevenness by placing spacers under the bottom of the cabinet. Make sure that the cabinet rests firmly on the floor without rocking.

c.Before the oven is fitted, the cabinet must be firmly secured to the backing wall for stability.

d.The oven unit should now be lifted (this is a two person lift) into the cabinet and pushed fully home.

e.Finally, the oven is secured to the cabinet by means of the four Pozi Wash Head screws - two through each side trim.

f.Remove all packaging material from the grill and oven interior.

LIST OF LOOSE ITEMS

4 x Pozi Wash Head No. 6 x 15mm screws.

Note: This appliance must not be installed over any other appliance that generates heat.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Europa S230G Creda Answer Centre 08701 54 64 Contents Introduction Always For Your SafetyNever Oven Timer Operation Automatic CookingHints on Automatic Cooking Clockface Know Your TimerSymbols Timer Function ButtonsSetting the Minute Minder Setting the Time of DAYAuto Cooking Programmes Electronic Clock & Automatic Oven Timer Operation Other Notes on Timer Operation ABC Grill PAN & HandleCooling FAN Using the GrillUsing the TOP Oven Shelf position 1 is the highest TOP Oven Cooking ChartYeast Mixtures Using the Main Oven Main Oven UtensilsMain Oven Operation Cold Start Cooking Using the ‘S’ Setting Main Oven Cooking Chart Small cakes 2 trays Mins Tray Victoria sandwich 2x8 205mm Care and Cleaning Credaclean Oven Liners Main Oven onlyCleaning GRILL, TOP Oven and Main Oven Replacement of the Oven Lamp HOW to Clean the Lamp LensOven Doors Cleaning the Doors Installation Instructions Ventilation InstallationFinal Installation GeneralTall Cabinet Ventilation 597mm Cabinets Less than 565mm Deep Connecting to GAS SupplyConnect to a 230-240V A.C. Supply only Electrical ConnectionInstallation and Operational Checks Something WRONG? Problem CheckPage Page Key Contacts

S230G specifications

The Creda S230G is a versatile and powerful electric storage heater that combines advanced technology with user-friendly features to provide efficient heating solutions for homes and commercial spaces. Designed with a modern aesthetic, the S230G seamlessly integrates into various interior designs while providing optimal warmth and comfort.

One of the standout features of the Creda S230G is its advanced energy storage capability. This heater operates by charging during off-peak energy hours, allowing users to take advantage of lower electricity rates. The unit stores heat in its ceramic bricks, which then gradually release warmth throughout the day, ensuring a consistent and comfortable indoor temperature. This not only promotes energy efficiency but also helps in reducing overall heating costs.

The Creda S230G is equipped with a built-in thermostat that allows for precise temperature control. Users can easily set their desired temperature, and the heater will automatically adjust its output to maintain that level of comfort. Additionally, the S230G features a manual control panel, making it easy to operate and customize heat settings to suit individual preferences.

Another notable technology integrated into the Creda S230G is its adaptive control system. This innovative feature learns the user's heating patterns and preferences over time, optimizing its performance to meet specific needs. This personal touch enhances comfort while ensuring energy is used efficiently, contributing to lower utility bills.

The heater's construction is robust, featuring high-quality materials that ensure durability and longevity. Safety is also a priority, with built-in overheat protection and a thermal cut-out feature designed to prevent potential hazards.

Installation of the Creda S230G is straightforward, making it a practical choice for both new builds and retrofitting projects. The unit can be mounted on walls to save space, and its compact size allows it to fit into various room layouts without being intrusive.

In summary, the Creda S230G stands out as an exceptional electric storage heater. Its energy-efficient design, user-friendly features, adaptive control system, and high-quality construction make it a reliable choice for heating needs. With the capability to provide consistent warmth while optimizing energy usage, the S230G is an ideal solution for those looking to enhance their living or working environment with effective heating technology.
Top Page Image Contents