Electrical Connection

WARNING – THIS APPLIANCE MUST BE EARTHED.

CONNECT TO A 230-240V A.C. SUPPLY ONLY.

Connection to the electricity supply should be made via a properly earthed, readily accessible wall socket which is adjacent to, and not more than 1.25m away from the appliance and capable of electri- cal isolation.

The mains lead should be routed such that it cannot touch hot parts of the appliance i.e. the back panel above a height of 350mm from the bottom of the oven recess. If the oven is to be wired into a connector unit, this may be positioned behind the oven providing the following requirements are met:

i)The connector unit must not project more than 25mm from the wall.

ii)The top of the connector unit must not be more than 350mm above the base of the oven recess.

NOTE: The removed plug cannot be used for any other appliance and should

therefore be properly disposed of and not left where children might find it and plug it into a supply socket – with the obvious consequent danger.

IF THE FITTED PLUG IS REMOVED

The flexible mains lead must be correctly connected as below to a three pin plug of not less than 13 amp capacity. If a B.S. 1363 fused plug is used, it must be fitted with a 3 amp fuse which is approved to B.S. 1362.

IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in

accordance with the following code:

GREEN AND YELLOW	– EARTH
		Blue to
BLUE	– NEUTRAL
		Neutral
BROWN	– LIVE

		Cord Clamp

Green &

Yellow to

Earth

Brown to Live

3 Amp

Fuse

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug,

proceed as follows:– The wire which is coloured green and yellow must be connected to the terminal

in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow. The wire which is coloured blue must be connected to the terminal which is marked with the N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. As the appliance must be earthed, do not use 2-pin sockets outlets, if you are in doubt, consult a qualified electrician.

Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same size i.e. 0.75mm2 cross sectional area and temperature rating of 850 C e.g. heat resisting PVC.

IF A MOULDED PLUG IS FITTED

In the event of replacing a fuse in the plug supplied a 3 amp ASTA approved fuse to BS1362 must be fitted.

NOTE: The fuse cover must be refitted when changing the fuse. In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been obtained and fitted. A new fuse cover can be obtained from your local electrical retailer. The colour of the correct replacement fuse cover is that of the coloured marks or inserts in the base of the plug.

S230G specifications

The Creda S230G is a versatile and powerful electric storage heater that combines advanced technology with user-friendly features to provide efficient heating solutions for homes and commercial spaces. Designed with a modern aesthetic, the S230G seamlessly integrates into various interior designs while providing optimal warmth and comfort.

One of the standout features of the Creda S230G is its advanced energy storage capability. This heater operates by charging during off-peak energy hours, allowing users to take advantage of lower electricity rates. The unit stores heat in its ceramic bricks, which then gradually release warmth throughout the day, ensuring a consistent and comfortable indoor temperature. This not only promotes energy efficiency but also helps in reducing overall heating costs.

The Creda S230G is equipped with a built-in thermostat that allows for precise temperature control. Users can easily set their desired temperature, and the heater will automatically adjust its output to maintain that level of comfort. Additionally, the S230G features a manual control panel, making it easy to operate and customize heat settings to suit individual preferences.

Another notable technology integrated into the Creda S230G is its adaptive control system. This innovative feature learns the user's heating patterns and preferences over time, optimizing its performance to meet specific needs. This personal touch enhances comfort while ensuring energy is used efficiently, contributing to lower utility bills.

The heater's construction is robust, featuring high-quality materials that ensure durability and longevity. Safety is also a priority, with built-in overheat protection and a thermal cut-out feature designed to prevent potential hazards.

Installation of the Creda S230G is straightforward, making it a practical choice for both new builds and retrofitting projects. The unit can be mounted on walls to save space, and its compact size allows it to fit into various room layouts without being intrusive.

In summary, the Creda S230G stands out as an exceptional electric storage heater. Its energy-efficient design, user-friendly features, adaptive control system, and high-quality construction make it a reliable choice for heating needs. With the capability to provide consistent warmth while optimizing energy usage, the S230G is an ideal solution for those looking to enhance their living or working environment with effective heating technology.