Daewoo KOR-861G0A, KOR-631G0A, KOR-861H0A, KOR-631G9A Installation, Leave space behind and side

Page 9

INSTALLATION

1. Steady, flat location.

This microwave oven should be set on a steady, flat surface.

2. Leave space behind and side.

All air vents should be kept a clearance. If all vents are covered during operation, the oven may be overheated and, eventually, cause oven failure.

3. Away from radio, and TV sets

Poor television reception and radio interference may result if the oven is located close to a TV, radio, antenna, or feeder and so on.

4. Away from heating appliances and water taps

Keep the oven away from hot air, steam or splash when choosing a place to position it, or the insulation might be adversely affected and breakdowns occur.

5.Power supply

Check your local power source.

This microwave oven requires a current of approximately 12/10(KOR-630A9A) amperes, 120Volts, 60Hz grounded outlet.

Power supply cord is about 0.8 meters long.

1.A short power-supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord.

2.Longer cord sets or extension cords are available and may be used if care is exercised in their use.

3.If a long cord or extension cord is used:

1)The marked electrical rating of the cord set or extension cord should be at least as great as the electrical rat- ing of the appliance.

2)The extension cord must be a grounding type 3-wire cord.

3)The longer cord should be arranged so that it will not drape over the counter top or tabletop where it can be pulled on by children or tripped over unintentionally.

6. Examine the oven after unpacking for any damage such as:

A misaligned door, broken door or a dent in cavity.

If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.

8

Image 9
Contents Microwave Oven Table of Contents Do not Attempt to Operate this Appliance with the Door Open Safety and PrecautionsSpecifications External View Outer DIMENSIONKOR-631G/H, 631G/H9/KOR-861G/HFeature Diagram KOR-861G0A Control PanelKOR-631H0A/631H9A/861H0A Leave space behind and side InstallationOperations and Functions Wattage output chartDisassembly and Assembly To remove cabinet Part Code Part Name Description REF no Part Code Part Name Description ’TY RemarkPage Control Panel Switch MembranePCB AS Screw Tapping T2S TRS 4X12 MfznTo remove high voltage capacitor To remove wind guide assembly Adjustment Interlock Mechanism and AdjustmentCondition Trouble Shooting GuideCheck Result CauseResult Cause Remedy CheckRelay RY1 Condition Check ResultContinuity of the membrane Touch Assembly Programming Measurement of the Microwave Power Output ProcedureMeasurement and Test Microwave Radiation Test ProceduresHigh voltage transformer Component Test ProcedureWiring Diagram Printed Circuit Board Circuit Check ProcedureLoad No Load Check Point RemarkMeasure Point GND State PointCheck no Method Point Wave FormPCB Circuit Diagram C.B. Location no Name Symbol Specification Part Code QTYCEXF1C102V Connector Wafer CN1 Wire Copper SJ1,SJ3 TIN CoatingCEXF1C101V Capacitor Elec EC2 Exploded View and Parts List Door AssemblyTotal Assembly Part Code Part Name Description QTY Lamp LockScrew Tapping T2S PAN 4X6 Mfzn Motor SyncroScrew Tapping T2S TRS 4X30 Mfzn Special Screw T1 TRS 4*10 SE MfznFAN PP+30% Glass Screw Special TT2 TRS 4X8 SE MfznLock POM Special Screw TT3 TRS 4X8 MfznCover Wave Guide Heatpro of PP NO. R631G0A003 Printed Date Aug