Whirlpool W10541636B If Ice Maker Is Currently Installed, Drain Cap, Water Supply Line

Page 5

If Ice Maker Is Currently Installed

NOTE: If ice maker is not installed, please proceed to “Drain Pump Installation” section.

1.Push the selector switch to the Off position.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

2.Unplug ice maker or disconnect power.

3.Turn off water supply. Wait 5 to 10 minutes for the ice to fall into the storage bin. Remove all ice from bin.

4.Unscrew the drain cap from the bottom of the water pan located inside the storage bin. Allow water to drain completely. Replace drain cap. See “Drain Cap” illustration.

Drain Cap

A

A. Drain cap

5.If ice maker is built into cabinets, pull ice maker out of the opening.

6.Disconnect water supply line. See “Water Supply Line” illustration.

Water Supply Line

 

A

 

 

B

B

 

 

 

 

C

 

 

D

 

C

 

 

E

 

A. ¹⁄₄" copper tubing

D. Ferrule (sleeve)

 

B. Cable clamp

E. Ice maker connection

 

C. ¹⁄₄" compression nut

 

 

Drain Pump Installation

NOTE: Do not kink, smash or damage tubes or wires during installation.

1.Unplug ice maker or disconnect power.

2.Remove rear panel. See “Rear Panel” illustration for 5 screw locations. Pull rear panel away from the drain tube and discard.

Rear Panel

A

A

A. Screw locations

3.Remove the old drain tube and clamp attached to the ice maker bin.

NOTE: Discard old drain tube and clamp.

4.Install new drain tube (⁵⁄₈" ID x 5¹⁄₈") from ice maker bin to drain pump reservoir inlet using new adjustable clamps. See “Drain Tube” illustration.

NOTES:

Do not kink.

Trim tube length, if required.

Drain Tube

 

A

 

B

 

C

 

D

A. ⁷⁄₈" adjustable hose clamp

C. ⁷⁄₈" adjustable hose clamp

B. Drain tube (ice bin to drain pump)

D. Drain pump reservoir inlet

5.Install vent tube (⁵⁄₁₆" ID x 32" [81 cm]) to drain pump reservoir vent. Use one ⁵⁄₈" small adjustable clamp, supplied. See “Parts Locations” illustration.

NOTE: Do not install household drain tube at this time.

5

Image 5
Contents Table of Contents/Table des matières ICE Maker SafetyCleaning Before Use Installation InstructionsUnpack the Ice Maker Location RequirementsWater Supply Requirements Electrical RequirementsVacation or Extended Time Without Use Connect Water SupplyKit Contains Ice Maker Drain Pump InstallationRear View Drain Pump Installation If Ice Maker Is Currently InstalledDrain Cap Water Supply LineVent Tube Drain Pump Mounting Tab SlotGravity Drain System Drain ConnectionSide View Drain Pump System on some modelsIce Maker Door Reversal-Side Swing Only Connecting the DrainOn Some Models Door Stop and End-Cap ReversalReplace Door Reverse HingesOn Some Models-Replace Door Wrap Top HingeInterior Components CleaningLeveling On Some Models Votre sécurité et celle des autres est très importante Sécurité DE LA Machine À GlaçonsExigences d’emplacement Instructions D’INSTALLATIONDéballage de la machine à glaçons Spécifications électriquesRaccordement à la canalisation d’eau Spécifications de l’alimentation en eauVacances ou longue période d’inutilisation Contenu de l’ensemble Installation de la pompe de vidange de la Machine à glaçonsVue arrière Installation de la pompe de vidange Si la machine à glaçons est installéeBouchon de vidange Canalisation d’alimentation en eauPosition des pièces Tube de vidangeTube de ventilation Raccordement au drain de vidangeVidange par gravité Vue latéraleRaccordement du drain de vidange Système avec pompe de vidange sur certains modèlesSur certains modèles Réinstallation du revêtement de porte Réinstallation de la porteInversion du sens de montage des charnières Charnière supérieureCharnière inférieure Inversion du sens dinstallation de la gâche de porteNivellement Composants intérieurs NettoyageSur certains modèles Imprimé aux É.-U