Whirlpool 2314466 manual Adjust the Doors, Caster Installation, Door Closing, Align Doors

Adjust the Doors

NOTE: If the casters are installed on your convertible refrigerator/ freezer, the leveling screws will not work. Shims can be placed under the casters to level a convertible refrigerator/freezer that has casters installed.

Door Closing

Your convertible refrigerator/freezer has two front adjustable rollers – one on the right and one on the left. If your convertible refrigerator/ freezer seems unsteady or you want the doors to close easier, adjust the convertible refrigerator/freezer's tilt using the instructions below.

1.	Remove the base grille. See Base Grille graphic in “Convertible
	Refrigerator/Freezer Doors.” The two leveling screws are part of
	the front roller assemblies which are at the base of the
	convertible refrigerator/freezer on either side.
2.	Use a screwdriver to adjust the leveling screws. Turn the leveling

Caster Installation

WARNING

Excessive Weight Hazard

Use two or more people to move and install convertible refrigerator/freezer.

Failure to do so can result in back or other injury.

Gather the required tools and parts before starting installation.

TOOLS NEEDED:

■ ¹⁄₂" Socket wrench or nut	■ ³⁄₈" Socket wrench or nut
driver	driver

screw to the right to raise that side of the convertible refrigerator/

freezer or turn the leveling screw to the left to lower that side. It

may take several turns of the leveling screws to adjust the tilt of

the convertible refrigerator/freezer.

NOTE: Having someone push against the top of the convertible

refrigerator/freezer takes some weight off the leveling screws and

rollers. This makes it easier to adjust the screws.

■¹⁄₂" Wrench

PARTS SUPPLIED:

■Rigid casters (2)

■Swivel casters (2)

■⁵⁄₁₆–18 Self-locking hex-nuts (16)

■⁵⁄₁₆–18 x ⁷⁄₈" Hex-head bolts (16)

■¹⁄₄–20 x 1¹⁄₄" Lock washers (4)

■¹⁄₄–20 x1¹⁄₄" Self-tapping Hex-head bolts (4)

■Caster brackets (located in FeaturePak) (2)

■Plastic skids (shipped with the convertible refrigerator/ freezer)

3.Open both doors again and check to make sure that they close as easily as you like. If not, tilt the convertible refrigerator/freezer slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.

4.Replace the base grille.

Align Doors

If the space between your doors looks uneven, you can adjust it using the instructions below:

1.Pry off the top hinge cover.

2.Loosen the top hinge screws using a ⁵⁄₁₆" socket or wrench.

3.Have someone hold the door in place or put a spacer between the doors while you tighten the top hinge screws.

4.Replace the top hinge cover.

1.Before you begin, turn the lower compartment control to off.

2.Unplug convertible refrigerator/freezer or disconnect power.

3.Remove food and any adjustable shelves and bins from convertible refrigerator/freezer.

4.Open the lower compartment door and remove the base grille. Remove the grille by grasping the grille with both hands, lifting up and pulling bottom of the grille toward you.

5.Place the plastic skids (shipped with the convertible refrigerator/ freezer) on the floor at least 3 ft (91.44 cm) apart. Lay a piece of cardboard or other protective material over the skids. This will elevate the convertible refrigerator/freezer to allow for easier caster installation and also protect it from scratches.

NOTE: If the skids have been discarded or are not available, 2" x 4" boards may be used.

6.Place the convertible refrigerator/freezer on its side on top of the cardboard or protective material. Make sure the door hinge is facing upward.

IMPORTANT: It is important that the door hinge face upward during the entire caster installation.

A

B

A. Top hinge

B. Center hinge

7