Blodgett RE Series manual Pressure Regulation and Testing, Inlet Pressure Natural Propane, KPa

Page 16

Installation

Gas Connection

PRESSURE REGULATION AND TESTING

Zephaire-G ovens are rated at 60,000 BTU/Hr. (17.6 kW) (63 MJ) per section. Each oven has been adjusted at the factory to operate with the type of gas specified on the rating plate.

Inlet Pressure

 

Natural

Propane

 

 

 

 

 

 

 

 

Min

 

Max

Min

 

Max

 

 

 

 

 

 

 

W.C.

7.0

 

10.5

11.0

 

13.0

 

 

 

 

 

 

 

kPa

1.43

 

2.61

2.74

 

3.23

 

 

 

 

 

 

Manifold Pressure

 

 

 

 

 

 

 

Natural

Propane

 

 

 

 

 

W.C.

 

3.5

 

10.0

 

 

 

 

 

kPa

 

.87

 

2.49

DInlet Pressure --- the pressure of the gas before it reaches the oven.

DManifold Pressure --- the pressure of the gas as it enters the main burner(s).

DMin --- the minimum pressure recommended to operate the oven.

D Max --- the maximum pressure at which the manufacturer warrants the oven’s operation.

Each oven is supplied with a regulator to maintain the proper gas pressure. The regulator is essen- tial to the proper operation of the oven and should not be removed. It is preset to provide the oven with 3.5” W.C. (0.87 kPa) for natural gas and 10.5” W.C. (2.50 kPa) for Propane at the manifold.

DO NOT INSTALL AN ADDITIONAL REGULATOR WHERE THE OVEN CONNECTS TO THE GAS SUPPLY UNLESS THE INLET PRESSURE IS ABOVE MAXIMUM.

Prior to connecting the oven, gas lines should be thoroughly purged of all metal filings, shavings, pipe dope, and other debris. After connection, the oven should be checked for correct gas pressure.

The oven and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.45kPa).

The oven must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas piping system at test pressures equal or less than 1/2 psig (3.45kPa).

Gas Connection 2.5” (64 mm)

Gas Connection 3.75” (86 mm)

Figure 10

12

Page 15 Page 17
Image 16
Page 15 Page 17
Contents ZEPHAIRE-G Avertissement Reputation YOU can Count on Page Table of Contents/Table des Matières Oven Description and Specifications GAS SpecificationsGAS Specifications -- Zephaire G-L for Australia Natural Gas Propane Gas US Units SI UnitsOven Components Delivery and Inspection Delivery and LocationOven Location Oven Assembly NSF BoltsCaster Assembly LEG AttachmentCasters for Single and Double Stacked Ovens Low Profile Casters for Double Stacked OvensDouble Section Assembly Oven LevelingCanadian installations Australia and general export installationsInstalling the canopy hood draft diverter VentilationInstalling the draft hood Direct Flue ArrangementUtility Connections --- Standards and Codes Gas Connection GAS PipingPressure Regulation and Testing Inlet Pressure Natural PropaneKPa Manifold Pressure Natural Propane KPaGAS Hose Restraint Electrical Specifications Electrical ConnectionAdjustments Associated with Initial Installation Initial StartupSafety Information Safety TipsWhat to do in the event of a power failure General safety tipsControl Description Single Speed BlowerOperation Single Speed Blower with Cavity Lights Dual Speed Blower Dual Speed Blower with Cavity Lights General Guidelines for Operating Personnel Operating TipsSuggested Times and Temperatures Cleaning and Preventative Maintenance Cleaning the OvenPreventative Maintenance Annual MaintenanceTroubleshooting Guide Possible Causes Suggested RemedyPage Specifications Pour GAZ Specifications Pour GAZ -- Zephaire G-L pour AustraliaDescription et Spécifications du Four Gaz Naturel Gaz Propane Unités US Unités SIÉléments du Four Livraison ET Inspection Livraison et ImplantationImplantation DU Four Montage du Four Boulons NSFAssemblage DES Pieds Montage DES RoulettesRoulettes pour four simple ou pour four super- posés Roulettes de bas profile pour deux fours super- posésAvertissement Montage DE LA Section DoubleMise À Niveau DU Four Installation du déviateur de tirage Installation aux États-- Unis et au CanadaHotte D’ÉVACUATION Type Voûte Installation de la hotte de tirage EN Prise DirecteBranchements de Service --- Normes et Codes Longeur Dimensions nominales De conduit Pieds Branchement de GazConduit DE GAZ ExemplePression à l’entrée Gaz Naturel Gaz Propane Réglage ET Test DE PressionKPa Pression au collecteur Gaz Naturel Gaz Propane Retenue DU Tuyau DE GAZ Spécifications Électriques Raccordement ÉlectriqueEt Canada Réglages À Faire Lors DE L’INSTALLA- Tion Initiale Mise en Marche InitialeInformations de Sécurité Conseils DE SécuritéQue faire en cas de panne de secteur Conseils généraux de sécuritéSoufflerie Une Vitesse Description DES CommandesUtilisation Soufflerie Une Vitesse avec Lumières de Cavité Lumières DE Cavité MARCHE/ARRÊTSoufflerie Deux Vitesses Soufflerie Deux Vitesses avec Lumières de Cavité Consignes Générales à l’Intention des Utilasateurs ConseilsDurées et Températures Suggérées Nettoyage DES Fours Nettoyage et Entretien PréventifEntretien Préventif Guide de Détection des Pannes Causes Probables SuggestionInsert Wiring Diagram Here Placer Schéma DE Câblage ICI

RE Series specifications

The Blodgett RE Series is a prominent line of commercial ovens designed to meet the rigorous demands of the foodservice industry. Renowned for its exceptional performance, durability, and efficiency, the RE Series combines cutting-edge technology with user-friendly features, making it a preferred choice for chefs and operators alike.

One of the standout features of the Blodgett RE Series is its advanced convection cooking technology. This technology ensures even cooking by utilizing a powerful fan and exhaust system, which circulates hot air throughout the oven cavity. This not only enhances cooking efficiency but also reduces cook times while maintaining consistent results. The ovens in this series are capable of achieving high temperatures quickly, making them ideal for a variety of cooking applications, from baking to roasting.

The RE Series is constructed with high-quality stainless steel, providing both durability and a sleek appearance that fits seamlessly into any commercial kitchen environment. Its robust build ensures longevity, standing up to the rigors of daily use in busy establishments. Additionally, the ovens are designed with easy-to-clean surfaces that facilitate sanitation and adherence to health regulations.

Another significant characteristic of the Blodgett RE Series is its intuitive control system. Featuring a user-friendly digital interface, operators can easily set cooking times, temperatures, and modes. This level of control allows for precise cooking, ensuring that dishes are prepared to perfection every time. Programmable recipes can also be stored, enabling consistency across multiple batches and minimizing the risk of human error.

Efficiency is a key focus of the RE Series, with models equipped to reduce energy consumption while maintaining high performance. The ovens are designed with insulation that minimizes heat loss, allowing for quicker preheating times and reduced energy usage over time. This not only benefits the environment but also helps reduce operating costs for foodservice operators.

Furthermore, the Blodgett RE Series offers versatility with various configuration options, including different sizes and rack capacities. This adaptability allows kitchen staff to use the ovens for a wide range of menu items, from pizzas to pastries, making it a valuable addition to any establishment, whether a small café or a large restaurant.

In summary, the Blodgett RE Series combines advanced cooking technology, durability, and user-friendly features to create an exceptional line of commercial ovens. With its focus on performance and efficiency, it is a reliable choice for foodservice professionals seeking to enhance their kitchen operations.
Top Page Image Contents