Blodgett RE Series manual GAS Hose Restraint, Australia and general export installations

Page 17

Installation

Gas Connection

GAS HOSE RESTRAINT

If the oven is mounted on casters, a commercial flexible connector with a minimum of 3/4” (1.9 cm) inside diameter must be used along with a quick connect device.

The restraint, supplied with the oven, must be used to limit the movement of the unit so that no strain is placed upon the flexible connector. With the restraint fully stretched the connector should be easy to install and quick connect.

The restraint (ie: heavy gauge cable) should be 1,000 lb. (453 kg) test load and should be attached without damaging the building. DO NOT use the gas piping or electrical conduit for the attachment of the permanent end of the restraint! Use anchor bolts in concrete or cement block. On wooden walls, drive hi test wood lag screws into the studs of the wall.

1.Mount the supplied bracket to the leg bolt just below the gas inlet. See Figure 11.

2.Attach the clip on restraining cable to the mounting bracket.

Back of Oven

Restraint Cable

Bracket

Double stacked unit shown. Use the same procedure for single units with 25” (64 cm) legs.

Figure 11

WARNING!!

If the restraint is disconnected for any reason it must be reconnected when the oven is returned to its original position.

U.S. and Canadian installations

The connector must comply with the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 or Connectors For Moveable Gas Ap- pliances CAN/CGA-6.16-M87and a quick discon- nect device that complies with the Standard for Quick-Disconnect Devices for Use With Gas Fuel, ANSI Z21.41 or Quick Disconnect For Use With Gas Fuel CAN 1-6.9. Adequate means must be provided to limit the movement of the appliance

without depending on the connection and the quick disconnect device or its associated piping.

Australia and general export installations

The restraint and quick connect must conform with Local and National installation standards. Lo- cal installation codes and/or requirements may vary. If you have any questions regarding the prop- er installation and/or operation of your Blodgett oven, please contact your local distributor. If you do not have a local distributor, please call the Blodgett Oven Company at 0011-802-860-3700.

13

Image 17
Contents ZEPHAIRE-G Avertissement Reputation YOU can Count on Page Table of Contents/Table des Matières GAS Specifications Oven Description and SpecificationsGAS Specifications -- Zephaire G-L for Australia Natural Gas Propane Gas US Units SI UnitsOven Components Oven Location Delivery and LocationDelivery and Inspection NSF Bolts Oven AssemblyLEG Attachment Caster AssemblyCasters for Single and Double Stacked Ovens Low Profile Casters for Double Stacked OvensOven Leveling Double Section AssemblyAustralia and general export installations Canadian installationsInstalling the canopy hood draft diverter VentilationDirect Flue Arrangement Installing the draft hoodUtility Connections --- Standards and Codes GAS Piping Gas ConnectionInlet Pressure Natural Propane Pressure Regulation and TestingKPa Manifold Pressure Natural Propane KPaGAS Hose Restraint Electrical Connection Electrical SpecificationsInitial Startup Adjustments Associated with Initial InstallationSafety Tips Safety InformationWhat to do in the event of a power failure General safety tipsOperation Single Speed BlowerControl Description Single Speed Blower with Cavity Lights Dual Speed Blower Dual Speed Blower with Cavity Lights Operating Tips General Guidelines for Operating PersonnelSuggested Times and Temperatures Cleaning the Oven Cleaning and Preventative MaintenancePreventative Maintenance Annual MaintenancePossible Causes Suggested Remedy Troubleshooting GuidePage Specifications Pour GAZ -- Zephaire G-L pour Australia Specifications Pour GAZDescription et Spécifications du Four Gaz Naturel Gaz Propane Unités US Unités SIÉléments du Four Implantation DU Four Livraison et ImplantationLivraison ET Inspection Boulons NSF Montage du FourMontage DES Roulettes Assemblage DES PiedsRoulettes pour four simple ou pour four super- posés Roulettes de bas profile pour deux fours super- posésMise À Niveau DU Four Montage DE LA Section DoubleAvertissement Hotte D’ÉVACUATION Type Voûte Installation aux États-- Unis et au CanadaInstallation du déviateur de tirage EN Prise Directe Installation de la hotte de tirageBranchements de Service --- Normes et Codes Branchement de Gaz Longeur Dimensions nominales De conduit PiedsConduit DE GAZ ExempleKPa Pression au collecteur Gaz Naturel Gaz Propane Réglage ET Test DE PressionPression à l’entrée Gaz Naturel Gaz Propane Retenue DU Tuyau DE GAZ Et Canada Raccordement ÉlectriqueSpécifications Électriques Mise en Marche Initiale Réglages À Faire Lors DE L’INSTALLA- Tion InitialeConseils DE Sécurité Informations de SécuritéQue faire en cas de panne de secteur Conseils généraux de sécuritéUtilisation Description DES CommandesSoufflerie Une Vitesse Lumières DE Cavité MARCHE/ARRÊT Soufflerie Une Vitesse avec Lumières de CavitéSoufflerie Deux Vitesses Soufflerie Deux Vitesses avec Lumières de Cavité Conseils Consignes Générales à l’Intention des UtilasateursDurées et Températures Suggérées Entretien Préventif Nettoyage et Entretien PréventifNettoyage DES Fours Causes Probables Suggestion Guide de Détection des PannesInsert Wiring Diagram Here Placer Schéma DE Câblage ICI

RE Series specifications

The Blodgett RE Series is a prominent line of commercial ovens designed to meet the rigorous demands of the foodservice industry. Renowned for its exceptional performance, durability, and efficiency, the RE Series combines cutting-edge technology with user-friendly features, making it a preferred choice for chefs and operators alike.

One of the standout features of the Blodgett RE Series is its advanced convection cooking technology. This technology ensures even cooking by utilizing a powerful fan and exhaust system, which circulates hot air throughout the oven cavity. This not only enhances cooking efficiency but also reduces cook times while maintaining consistent results. The ovens in this series are capable of achieving high temperatures quickly, making them ideal for a variety of cooking applications, from baking to roasting.

The RE Series is constructed with high-quality stainless steel, providing both durability and a sleek appearance that fits seamlessly into any commercial kitchen environment. Its robust build ensures longevity, standing up to the rigors of daily use in busy establishments. Additionally, the ovens are designed with easy-to-clean surfaces that facilitate sanitation and adherence to health regulations.

Another significant characteristic of the Blodgett RE Series is its intuitive control system. Featuring a user-friendly digital interface, operators can easily set cooking times, temperatures, and modes. This level of control allows for precise cooking, ensuring that dishes are prepared to perfection every time. Programmable recipes can also be stored, enabling consistency across multiple batches and minimizing the risk of human error.

Efficiency is a key focus of the RE Series, with models equipped to reduce energy consumption while maintaining high performance. The ovens are designed with insulation that minimizes heat loss, allowing for quicker preheating times and reduced energy usage over time. This not only benefits the environment but also helps reduce operating costs for foodservice operators.

Furthermore, the Blodgett RE Series offers versatility with various configuration options, including different sizes and rack capacities. This adaptability allows kitchen staff to use the ovens for a wide range of menu items, from pizzas to pastries, making it a valuable addition to any establishment, whether a small café or a large restaurant.

In summary, the Blodgett RE Series combines advanced cooking technology, durability, and user-friendly features to create an exceptional line of commercial ovens. With its focus on performance and efficiency, it is a reliable choice for foodservice professionals seeking to enhance their kitchen operations.