Sunfire TGR-401-230, TGR401 manual Zone 2 Connections, Zone 2 OSD menus

Zone 2 Connections

As an alternative to using the TGR-
401's internal ampli ers to run your	Connection to IR
Zone 2 speakers, you could use an
external power ampli er. Connect the	receiver in Zone 2
ampli er's line-level inputs to the TGR-
401 Zone 2 stereo outputs.

Speaker-level audio signals	+	+
	TO LEFT
From: Receiver speaker outputs
	ZONE 2	TO RIGHT
To: Zone 2 speaker inputs
	SPEAKER
		ZONE 2
		SPEAKER

CHAPTER 2

Zone 2 OSD menus

MAIN MENU

TRIMS

TONE CONTROLS

MODES

PRESETS

SETUP

SETUP	CHOICES
INPUTS
SPEAKERS
VIDEO
MAIN ZONE
ZONE 2
CONTROL
DIGITAL OUT	DN MIX/THRU
DIMMER	LOW/MEDIUM/HIGH
ZONE 2			CHOICES
FIXED VOLUME		N	N, 0.0 - 100.0
PWR UP MAX VOL		60.0	0.0 - 100.0
PWR UP MIN VOL		0.0	0.0-100.0 MUST BE LESS THAN POWER
			UP MAX VOLUME
MAX VOLUME		100.0	0.0-100.0 MUST BE MORE THAN POWER
			UP MAX VOLUME
PWR UP SOURCE		LAST	LAST, INPUT 1,INPUT 2, ... INPUT 8, AM,
			FM, SIRIUS, FRONT

Zone 2 can play stereo analog sources independently of the Main Zone, or play the same source. Zone 2 can only play a digital source if the Main Zone is playing the same source.

A composite video output is avail- able for monitoring in Zone 2. Note that the video sources you would like to play in Zone 2 must use compos- ite video, or you will not see video in Zone 2.

If you want the TGR-401 speaker- level outputs to run your Zone 2 speakers, under the OSD Binding Post menu, set "POWERED Z2" to ON.

Speaker wires are connected to the speaker outputs as shown above, and are run out to Zone 2 speakers, located in another room or area of your house.

If you have an external power ampli er to run your Zone 2 speakers, connect the TGR-401 Zone 2 line-lev- el stereo outputs to the inputs of your ampli er. Connect your Zone 2 speak-

ers to the ampli er with speaker wire. This method provides full-time 7.1 for the home theater, plus an ampli ed Zone 2.

The wire from an optional IR sensor is shown connected to the TGR-401 Zone 2 IR input. The TGR-401 is com- patible with most makes of IR sensors and equipment.

The sensor can be located in a suitable area of Zone 2, allowing you complete control of the volume and source selection. Zone 2 can also be controlled from the front panel, using the remote's Zone 2 buttons.

The optional Olé-2SF Film Interac- tive touchpads are precon gured to operate Zone 2. They connect to ei- ther the TP1 or TP2 connectors on the TGR-401 rear panel. The touchpads allow you to control the source selec- tion, volume, bass, and treble. Also, they will pass IR commands back to the TGR-401, as they have an internal IR receiver. For custom programming, please contact your Sun re dealer.

BASS	0	+14 TO -14, 2 DB STEPS
TREBLE	0	+14 TO -14, 2 DB STEPS
BALANCE	0	-20 TO +20, 1 DB STEPS

SPEAKERS

AUTO SETUP

SPEAKER SIZE

DISTANCE

LEVEL CALIBRATION

EQ

BINDING POSTS

BINDING POSTS		CHOICES
AMP SECTION	ON	ON, OFF
FRONT	ON	ON, OFF
SURROUND	ON	ON, OFF
CFG POST	OFF	OFF, FRONT, SURR
POWERED Z2	OFF	ON/OFF

The ZONE 2 menu allows you to:

•Set a xed volume

•Set max and min volume at Zone 2 power-up

•Set a maximum volume

•Select a source to play at Zone 2 power-up

•Adjust bass, treble and balance

The Binding Posts menu allows you to:

•Power the Zone 2 speakers or

•Power the Main Zone surround back speakers

User's Manual

23