Sunfire TGR401, TGR-401-230 manual Remote Setup, Punch, Erase, Light, Learn

Page 28

CHAPTER 3

Remote Setup continued

PUNCH

This mode allows you to set up the volume, channel up/down and trans- port buttons so they will work for your main devices, no matter which device the remote is set for. For example, the volume buttons can operate the TV, even if the remote is set to VCR. The channel buttons can operate the VCR, even if the remote is set to TV.

1.In SETUP, select PUNCH and the display changes to show VOL, CH, PLAY, MENU, and POWER. The MENU selection will make the eight transport buttons around the navigation pad punch through.

2.Select one of these buttons, for example VOL.

3.Press a device button for the device you want the Volume com- mands to appear in (punch TO).

4.Press a device button for the de- vice you want to learn from (punch FROM). These settings are saved.

5.Repeat steps 2 to 4 until you have punched to all devices you want.

6.Use MAIN to return to SETUP.

NOTE: To erase Punch commands from a device and so return but- tons to their previous program- ming: Repeat steps 1 and 2, then press the device button twice. Re- peat for other devices, then press MAIN to return to SETUP.

The operation of the optional VIA!migo iPod dock relies on the navigation buttons when the remote is set to operate the MP3. Therefore, it is best that you do not punch-to the MP3. Also, do not punch-to the TG401, in case you program over the navigation buttons used with the OSD menus and the SIRIUS tuner opera- tion.

ERASE

Use this mode to erase commands stored in the remote. This does not affect the labels, just the stored IR commands. The pre-programmed commands for the TGR-401 will not be lost, as they can be recalled.

1.In the SETUP mode, select ERASE and the display will show LEARN, FAV, MACRO and EXIT.

2.If you select LEARN, press ALL to erase all learned buttons, or KEY to erase one device at a time, or DEVIC. If you use KEY, press MAIN and EXIT when you have erased all the devices you want.

3.If you select FAV, press ALL to erase all favorites, or KEY to erase single favorites. Note that the labels are not erased.

4.If you select MACRO, press ALL to erase all macros, or KEY to erase macros, one device at a time.

5.Press EXIT to return to the SETUP menu, and press MAIN to return to the main device menu.

LIGHT

This mode allows you to either dis- able the light, or change the number of seconds it stays on. (The light is inactive while in the SETUP mode).

1.In the SETUP menu, select LIGHT and the display will show ON, time in seconds, SAVE and EXIT.

2.If you press ON, it changes to OFF and disables the light. This is use- ful if you want to save battery life, or if the kids like to use the remote as a ashlight or Light Saber ®.

3.Use the keypad to enter the num- ber of seconds you want the light to stay on. If you enter 00, it only stays on while the light button is held down.

4.Select SAVE, or press EXIT to make no change. Either of these will return you to the SETUP menu.

LEARN

The remote can learn commands from other remote controls. This is useful if the pre-programmed com- mands do not operate some of your equipment, or certain buttons do not work, or you want to customize key functions.

NOTE: PAGE, MAIN, and FAV can- not be learned over.

1.Find your original remote and make sure it has good batteries, and it operates your equipment perfectly. In the following example, the Sun re remote will learn the PLAY command from a DVD re- mote.

2.Point the DVD remote into the Red IR top window of the Sun re re- mote. Place them on a at surface, about 1 to 2 inches apart, and avoid bright lighting or sunlight.

3.In the SETUP mode, press

LEARN.

4.Select the DVD device button and the display will change to show some common DVD labels (re- member there are two pages).

5.Select the PLAY button just above the navigation pad. The display will show “READY.”

6.Press your DVD remote’s PLAY button. The display will show “GOOD” if it has been accepted. If it shows “FAIL,” press PLAY again.

7.Press another button on the Sun re remote and repeat the procedure until all the DVD buttons you need are learned.

8.Press MAIN once to return to the LEARN mode, twice for SETUP and three times for the MAIN menu.

28

User's Manual

Image 28
Contents Theater Grand Receiver Important Safety Instructions SafetyNEC National Electrical Code Contents Introduction Unpacking Power On/off OverviewAutomatic Setup Quick Start GuideOSD Menus EQ AdjustmentConclusion Front Panel Features IR Receiver Window Main SelectZone 2 Select Sonic HolographyRear Panel Features HdmiPower Switch Digital Connections11. TP1 and TP2 RS-232 Port VIA!migo PortInstallation AC Power ConsiderationsCare Connection TipsSystem Con gurations Analog Audio and Composite Video VCRDigital Audio and Component Video Connections DVD CD and Antenna Connections AM Loop AntennaTape Player Connections Channel Analog Input Connections Blu-ray or HD-DVD Front Panel Input Connections Component Video with Digital AudioOutput Connections Line-Level OutputsLeft/Right 2 Outputs Surround Back OutputsSurround 2 Outputs Zone 2 Connections Zone 2 OSD menusOptional Connections Sirius Satellite RadioVIA!migo iPod dock Olé-2SF TouchpadsMain Remote ControlFAV Operating the TGR-401 with the Remote ZoneRemote Setup PRORemote Setup PunchErase LightRecal Recall MacroEdit Chapter Clone Hiding and Adding PagesOSD Activation On Screen Display OSDQuick Information OSD Menus OSD Menus Trims, Tone, Modes, Presets, Setup Input See nextOSD Menus Setup, Inputs OSD Menus Setup NextOSD Menus Setup/Speakers/EQ Using the TGR-401 Input settingsBass Management Video ConversionManual Setup Automatic Setup Procedure Automatic and Manual Equalization Manual EQ adjustmentAuto EQ Mode Selection Surround Modes for 2-Channel SourcesSurround Modes for Multi-Channel Sources DTS 96/24 Sunfire DTS-ES 96/24 Matrix DTS-ES 96/24 DiscreteDTS Digital Surround DTS NEO6 Dolby Headphone Sonic Holography To summarizeFM and AM Tuner Operation Saving PresetsChanging Modes Recording Recording to a Tape PlayerIndicators Turning on Zone Zone 2 OperationAudio Connections Zone 2 OSD menuTriggers Trigger OSD MenuSpeaker Placement AppendixAppendix Front SpeakersSurround Speakers LS1/LS2 OptionsSurround Back Speakers Subwoofer LocationRS-232 Port Troubleshooting Guide No sound from one or more speakersTGR-401 does not respond to any controls Updating firmware problems Remote Control Codes see remote control P-Pro on DVD Recorders Changers Speci cations Default Input Table Optional VIA!migo iPod Dock Using the VIA!migo Optional Sirius Satellite Radio Tuner Tion of the frontSirius Tuner Operating Instructions Setting presetsActivation General tuning and use TroubleshootingOptional Olé-2SF Touchpads Sun re Limited Warranty Service AssistanceTheater Grand Receiver TGR-401 TGR-401-230 Manual TGR-401
Related manuals
Manual 68 pages 17.08 Kb