Optional VIA!migo iPod Dock

REMOTE IN S-VIDEO VIDEO

L AUDIO R

10V DC DATA I/O

1 2 2 3 3 4 5

APPENDIX

1. Remote Input

This connection is not required for connecting to the TGR-401 (see #5 below). It allows you to send remote control commands from 3rd party controllers to the VIA!migo dock via the rear panel.

2. Video Outputs

Connect either of these outputs to a video input of the TGR-401. Composite video 4 and S-Video 4 are the default video inputs for MP3.

You will be able to see the menu system and "now playing" infor- mation from the iPod on your TV monitor, and see movies (in full color) if you are using a video iPod.

If you use the composite output, the video will be available to Zone 2 as well as the Main Zone. The TGR-401 will upconvert to com- ponent.

Even if you do not have a video iPod, you must make the video connection, or it will not be easy to navigate through your song lists and select songs.

Analog input 4 is the default input for MP3, and must be used for feedback if you are using the optional Olé-2SF touchpad.

4. DC Input

The supplied power supply con- nects here. Do not use any other power supply. The VIA!migo will charge the iPod.

5. Data I/O

This connector is used with standard Cat-5 Ethernet cable to join the VIA!migo to the VIA!migo connector on the TGR-401.

The connection allows iPod metadata (such as song title, artist name, and album) to pass to the TGR-401 for display on the front panel, on-screen, or in the op- tional Olé-2SF touchpads.

6. IR Receiver

This allows you to use the remote control to operate your iPod.

The remote should rst be set to MP3, then it can be used to search through the iPod menus, select songs and play them (see next page).

Default settings

This OSD menu shows the default settings of the MP3 input, and is found in the Main Menu/Setup/In- puts menu.

	INPUT 4	CHOICES
ZONES	M/Z2	OFF, MAIN, ZONE 2, M/Z2
NAME	MP3	(UP TO 10 LETTER, NUMS AND
		SPECIAL CHARACTERS
GAIN TRIM	0.0 DB	-20 TO + 20 DB
ANA AUDIO	4	N, 1, 2, 3, 4, 8 CH (N = NO
		ASSIGN)
DIGITAL	COAX4	N, COAX 1-4, OPT 1-4
COMPOSITE	4	N, 1-4
S VIDEO	4	N, 1-4
COMPONENT VIDEO	N	N, 1-3
HDMI	N	N, 1-3
VIDEO DELAY	0 MS	0-180 MS IN 5 MS STEPS
AUTODET ANA	N	N/Y
AUTODET DIG AUD	N	N/Y
AUTODET CV	N	N/Y
AUTODET SV	N	N/Y
AUTODET COMPON	N	N/Y
2-CH ANALOG	LAST	LAST, STEREO, MONO, PARTY,
		PLIIX MUSIC, PLIIX MOVIE,
		PLIIX GAME, PLIIX MATRIX,
		NEO:6 MUSIC, NEO:6 CINEMA,
		JAZZCLUB, SRC DIRECT
2-CH DIGITAL	LAST	LAST, STEREO, MONO, PARTY,
		PLIIX MUSIC, PLIIX MOVIE,
		PLIIX GAME, PLIIX MATRIX,
		NEO:6 MUSIC, NEO:6 CINEMA,
		JAZZCLUB,
DOLBY	LAST	LAST, DIGITAL, DIGITAL EX,
		PLIIX MUSIC, PLIIX MOVIE
DTS	LAST	LAST, DIGITAL SURROUND,
		NEO:6, SUNFIRE
DTS96	LAST	LAST, DTS 96/24, NEO:6,
		SUNFIRE

This menu shows that if MP3 is selected as an input, the video is expected to come into input 4 (S-video or composite), and the audio into analog audio input 4.

The audio is 2-channel analog, so the last 4 selections in this table for digital audio are not used in

3. L/R Audio Outputs

Connect these analog audio outputs to the analog L/R inputs of the TGR-401. You will be able to hear the audio output from your iPod.

7. Power LED

This will light when the VIA!migo is turned on. Use the remote control (in MP3 mode) to turn it on and off remotely.

this application.

If the VIA!migo is connected to inputs other than 4, use this menu to select the inputs you are using.

Once the VIA!migo has been connected to the TGR-401, see the operation details on the next page.

User's Manual