Acme Kitchenettes PP-32 manual Mounting Instructions, Connection

Page 11
LOCKING
DEVICE

4. MOUNTING INSTRUCTIONS

Fasten the four metal brackets on the mounting holes located behind the controller using the four screws included with the controller. Mount the enclosure on the wall using four other

screws. Make sure the electrical knockouts are at the bottom of the enclosure in order to prevent water from entering the control- ler. The enclosure must be mounted in a

location that will allow the cover to be completely opened right up against the wall. Push on the locking devices to open

the enclosure as illustrated.

4.1 CONNECTION

To connect the controller, refer to the wiring diagram enclosed with this user's manual. Use the electrical knockouts provided at the bottom of the enclosure. Do not make additional holes in the enclosure, particularly on the side of the enclosure when using a computer communications module.

1. SENSOR INPUTS

ROOM TEMPERATURE SENSORS

HUMIDITY SENSOR

(Refer to the main wiring diagram)

STATIC PRESSURE SENSOR (Refer to the main wiring diagram)

WATER METER

OUTSIDE T° SENSOR

ALL WIRING MUST BE DONE BY AN AUTHORIZED ELECTRICIAN ! AND MUST COMPLY WITH APPLICABLE CODES, LAWS AND REGULATIONS. BE SURE POWER IS OFF BEFORE DOING ANY WARNING WIRINGTOAVOIDELECTRICALSHOCKSANDEQUIPMENTDAMAGE.

KOOLMASTER PP-32 REV.01 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents PP-32 Page Table of Contents History Alarm SettingsInstallation Auxiliary Outputs Animal AGE Clock OutputsPP-32 Do not Spray Water on the Controller PrecautionsFeatures Password Protection Front Panel Location of the ControlsShortcut Keys Destination Connection Mounting InstructionsNot ground the shielding AlarmDWR-F-1A Communication Hookup DIP Switch Table Setting the DIP SwitchesStatic Pressure current static pressure in the barn Room Set Point this is the target temperature in the barnCurrent Conditions Selecting a Season Controller ProgramsSelecting a Program PP-32 Adjusting the Room SET Point Minimum Ventilation Minimum Ventilation TimerAdjusting Minimum Ventilations On-Time Adjusting Minimum Ventilations Cycle Time Setting DWR-F-1As ID numbers Inlet / Vent Door SettingsInlet Settings Potentiometer Feedback from Inlets Adjusting the Air Inlet Compensation Vent Doors Operation Vent Door SettingsGroups of Static Pressure SET Points Influenced by Ventilation StagesInfluenced by the Outside Temperature Adjusting Vent Doors Open / Close / Off Times Adjusting Static Pressure Set PointsVent Doors Timer 2.4 2nd Group of Pressure Set Points at Stage Adjusting Stage Level for the Closing of Vent Doors2.5 2nd Group of Pressure Set Points at Outside T PP-32 Tunnel Curtain Tunnel Curtain Timer ModeTunnel Curtain Controlled by the Static Pressure Tunnel to Vent Doors Vent Doors to TunnelSelecting the First Tunnel Stage Adjusting Minimum Age for Tunnel VentilationAdjusting Curtains Operating Times Adjusting Curtains Timer Cycle Adjusting Static Pressure Hi and Lo Set PointsCurtains Timer Operation of FAN Stages FAN Stages SettingsAdjusting Fans Stages Timer FAN Stages TimerAdjusting Fan Stages Start/Stop Temperatures PP-32 Operation of Heater Stages Heater SettingsAuxiliary Outputs Auxiliary Outputs in Heating ModeAuxiliary Outputs in Cooling Mode Adjusting Start/Stop Temperatures of Auxiliary Outputs Animal AGE Setting the Animal AgeOperation of Clock Outputs Clock OutputsStart Time / Stop Time Definition Operation of Clock Outputs 1Adjusting Clock Output Start and Stop Times Adjusting Starting Day of Clock Programs History Resetting HistoriesAverage Temperature History Relative Humidity History Individual Temperature Sensors HistoryOutside Temperature Sensor History Heater Run Time History Water Consumption HistoryPP-32 Alarm Log Alarm SettingsOustide Temperature Influence on Alarms Regular Temperature Alarm DetectionSetting Alarm Limits Adjusting Hi/ Lo Temperature Alarms Alarm Detection with Outside T InfluenceAdjusting the Outside Temperature Influence Adjusting Critical TemperatureHI Static Pressure Alarm Adjusting Static Pressure AlarmsLO Static Pressure Alarm Set the Lo Alarm Limit to Off to deactivate this featureAdjusting High/Low Delays Adjusting the Open-Time for the Hi Static Pressure Alarm Resetting the Alam LogStep-by-Step Installation Guide InstallationPP-32 Entering the Installers Password Password SettingsModifying the Installers Password Installation Setup 10.# of Inlets Auxiliary Output ModeUse Static Pressure ? Static Pressure Set17.# of Clock Programs for Clock Outputs 1 Use Outside Temperature Sensor ?Installer Password 16.# of Clock OutputsAssigning Sensors to the Room T and Fan Stages Sensor AssignmentAssigning Sensors to Air Inlets Assigning Sensors to Heater StagesAssigning Sensors to Auxiliary Outputs √√√ Relay Assignment Setting Time and DateAn empty template is available at the end of this manual Relay Assignment ExampleAssigning Fan Stages Relays Timer Relays on FAN StagesTo .7.2 to set the timers on and OFF time settings Assigning Vent Doors Open / Close Relays Assigning Heater Stages RelaysAssigning Relays to Vent Doors Assigning Curtains Open / Close Relays Assigning Relays to the Tunnel CurtainAssigning Relays to Auxiliary Outputs Assigning Relays to Clock OutputsAssigning Relays for the Lo Static Pressure Alarm Calibrating the Water Counter Setting the Temperature Curve Advanced SettingsTemperature Curve PP-32 Minimum Ventilation Curve Setting the Minimum Ventilation CurvePP-32 Humidity Control Adjusting Relative Humidity Set PointRH Compensation on Minimum Ventilation Humidity Compensation on MIN. VentilationHumidity Compensation on Heaters Adjusting Mist or Kool-Cel ShutoffAdjusting Heater Timer Cycle PP-32 Calibrating the Relative Humidity Sensor Calibrating SensorsCalibrating Room and Outside T Sensors Select 8.Vents/Static P from Calibrating the Static Pressure LevelTest Mode Technical Specifications Factory Settings Using the Configuration Module Start Configuration Press +/- to startContact Information Sensor Assignement Sensor Assignment Template see secInstallation Setup Template see sec Installation SetupRelay Assignment Template see sec ProcedureOUTPUT/ Relay # Index Installer password Keys see also buttons Setup

PP-32 specifications

The Acme Kitchenettes PP-32 is a versatile and compact solution for modern living spaces, ideal for those seeking functionality without sacrificing style. This kitchenette is perfect for apartments, studios, and locations with limited space, offering a blend of convenience and elegance.

One of the standout features of the PP-32 is its efficient layout. The kitchenette is designed with a compact footprint that maximizes usability while fitting easily into small areas. It includes essential components such as a sink, cooking surface, and storage, all seamlessly integrated to provide a fully functional cooking experience. The PP-32 comes equipped with a two-burner electric cooktop, allowing you to prepare meals with ease. This cooking surface is engineered for quick heating and energy efficiency, making it perfect for busy lifestyles.

The stainless steel sink is another significant aspect of the PP-32, designed to resist tarnishing and scratches while maintaining a sleek appearance. Its integrated faucet ensures that you have the water access needed for cooking or cleaning up. Additionally, the cabinetry includes ample storage space, featuring cabinets and drawers designed to hold cooking essentials, utensils, and pantry items. This storage solution is both functional and aesthetically pleasing, with a modern finish that complements any décor.

In terms of technology, the PP-32 incorporates advanced features that enhance its usability. The kitchenette is equipped with energy-efficient lighting that brightens the workspace while keeping energy consumption low. Additionally, the inclusion of easy-to-clean surfaces ensures that maintenance is simple, allowing for a tidy living environment.

The Acme Kitchenettes PP-32 also boasts a straightforward setup process, making it easy to install even in tight areas. With its thoughtful design and modern features, this kitchenette represents an ideal solution for those who value both efficiency and style in their living spaces.

In conclusion, the Acme Kitchenettes PP-32 provides a seamless blend of functionality, technology, and contemporary design. It caters to the needs of urban dwellers and those in smaller living setups, ensuring that cooking and meal preparation becomes an enjoyable experience. Whether for personal use or in rental properties, the PP-32 stands out as a reliable and attractive kitchenette option.
Top Page Image Contents