Vermont Casting 4075, SDVR, PDV20: 3920, 3930, 4070 Through Side Wall Vent Termination Below Grade

Page 15

Pinnacle & Stardance Direct Vent - Rear Vent Gas Heaters

9³⁄₈” W x 10³⁄₈” H

Firestop

Wall Opening

Ventilated Wall Plate -

Wall Sleeve -

Open End Down

Seal Around

Finishing Collar

 

25³⁄₄"

 

(654mm)

 

to Top of

 

Opening

 

Seal

 

Around

 

Terminal

 

ST400

 

Fig. 19 PDV20 with Rear Vent Kit 7TFSRSK installation.

3.Measure the wall thickness and cut the wall sleeve sections to proper length (MAXIMUM 12”). Assemble the sleeve with the #8 sheet metal screws supplied. Attach the firestop plate to the sleeve end with the holes. (Fig. 25) NOTE: The wall sleeve is required in combustible walls only.

4.Install the Wall Firestop/Sleeve assembly into the wall cutout and fasten the firestop to the wall cutout framing members. (Figs. 18, 19)

5.Measure, and cut if necessary, the appropriate length of pipe section needed to make the connec- tion through the wall.

6.Slip the wall plate and trim collar over the interior end of the horizontal pipe and install into the wall sleeve. Seal the joint inside the wall plate if needed to keep cold air from being drawn into the home.

7.Connect the pipe to the inner collar. Fasten the wall plate to the pipe with three sheet metal screws. Slide the trim collar up against the wall plate to cover the screws. (Figs. 18, 19)

8.Install the vent terminal. (Figs. 18, 19) Guide the inner and outer vent termination collars into the adjacent pipes. Double check that the vent pipes overlap the collars by 2”. Fasten the termination to the wall with the screws provided, and caulk the joint with weatherproof sealant.

Through Side Wall /

Vent Termination Below Grade

Refer to Figures 20 & 21 for minimum centerline of wall opening.

1.Attach Inner Starter Pipe, (found in with the logset), to the stove.

• Run a bead of sealant beneath the pipe bead and attach to the stove using three 1/4-20 x 3/8” phillips screws provided in the parts bag. (Fig. 22)

59¹⁄₄"

(1505mm)

 

ST131c

Fig. 20

Minimum wall thimble centerline.

 

61"

 

(1549mm)

 

ST131b

Fig. 21

Minimum wall thimble centerline.

2.Dry fit the inner and outer pipe of the first elbow directly to the starter pipe.

3.Dry fit the Inner pipe assembly to the stove for the purpose of determining the center line of the pipe on the wall.

• Side Wall Terminations: Dry fit the outer elbow with the vertical outer vent and confirm the centerline alignment with the wall thimble opening.

20007066

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Pinnacle & Stardance Direct Vent, Rear Vent Gas Heater Table of Contents Installation & Operating Instructions Stove Dimensions Stardance Direct Vent Gas Heater Stove Dimensions Pinnacle Direct Vent Gas HeaterMinimum Clearances to Combustible Materials Clearance RequirementsInput Model Fuel Gas Control BTU/h Gas SpecificationsMantel Clearances Hearth Requirements Gas Inlet and Manifold PressuresHorizontal Termination High ElevationsVent Termination Clearances Vertical TerminationLocation of Vent Termination General Venting Information Termination Location Canadian Installations1 US Installations2Termination Clearances Vent Components Unpack the Stove InstallationInstall Optional Fan Kit #2960/FK28 Fan Kit ContentsGeneral Information Venting System Assembly Direct VentFor U.S. installations The venting system must For Canadian installations The venting system mustThrough Side Wall Vent Termination Below Grade PDV20 with Rear Vent Kit 7TFSRSK installationInstall inner starter pipe and inner elbow Side Wall Termination AssemblyDetermine the vertical pipe length ³⁄₈ x 9³⁄₈ 240 x 240mm Vertical Through the Roof Vent AssemblyFireplace Vent Termination Clearances Vertical Through Existing ChimneyFireplace Vent System Fireplace Installation Requirements PDV20 Fireplace Installation Requirements Sdvr Burner Information Complete the AssemblyInstall ON/OFF Switch R Models only Connect the Gas Supply LineUse only a thermostat rated for 500 750 millivolts Install the Front PlateThis completes assembly of the PDV20 and Sdvr stove Thermostat ConnectionLogs Install the Log SetYour First Fire Flame & Temperature AdjustmentFlame Characteristics OperationCorrect pilot flame pattern. PSE Pilot Lighting And Operating Instructions To Turn Off Gas To HeaterWhat to do if YOU Smell GAS Symptom Possible Causes Corrective Action Troubleshooting / Honeywell #8420 Gas Control SystemDelay Timer Mode Shut Off ProcedureTransmitter Operation Off Mode On Manual ModeDisable Thermostat Function Auto ModeFan Override During Auto Mode Change Between F/C Temperature UnitsLocal Path Fuel Conversion Instructions Conversion PrecautionsConversion Procedure Auto PathPilot Type Models 3920, 3930, 4065, 4070 R Models OnlyConversion to LP Input BTU/h Models 3960, 3970, 4075, 4080 RF Models OnlyAll Models Conversion to Natural Gas Input BTU/hMaintenance Gasket Replacement Inspect the Vent System AnnuallyCheck the Gas Flame Regularly Wiring Diagrams Stove DisassemblyPinnacle PDV20 / Stardance Sdvr Direct Vent/Rear Vent PDV20 Sdvr DescriptionFuel Conversion Kits Screen Kit Optional AccessoriesRemote Controls Fan KitsIf Warranty Service is NEEDED… Product Covered by this WarrantyCFM Specialty Home Products

3966, 4080, 3926, 3936, 3960 specifications

Vermont Casting is renowned for its craftsmanship and quality in the hearth industry, particularly with its range of wood and gas stoves. Among its standout models are the 4065, 4075, 4070, 3976, and 3970. Each of these models presents unique features and advanced technologies that cater to a variety of heating needs and preferences.

The Vermont Casting 4065 model is designed with efficiency and usability in mind. Its advanced air management system allows for precise control over combustion, ensuring that homeowners enjoy a longer burn time while minimizing emissions. The large glass door provides an excellent view of the fire, making it a centerpiece in any room. Additionally, the 4065 is built from heavy-duty cast iron, which not only enhances durability but also retains heat longer.

Moving on to the 4075 model, this stove offers an impressive heat output, making it suitable for larger spaces. The 4075 incorporates a unique catalytic combustor, which boosts efficiency by enabling cleaner burns and reducing smoke output. This model also features a user-friendly ash removal system, simplifying maintenance and enhancing user experience.

The 4070 model stands out with its modern design and customizable options. It comes in various colors and finishes, allowing homeowners to tailor it to their interior design style. Like the other models, it emphasizes efficiency with a built-in heat exchanger, maximizing heat transfer to the surrounding space and ensuring optimal comfort.

The Vermont Casting 3976 is a powerhouse of innovation. Equipped with Vermont Casting’s signature cast iron construction, it provides exceptional heat retention and distribution. It features a powerful blower option that can be added for enhanced heat circulation, making it ideal for larger homes or open floor plans. The 3976 also boasts an easy-to-use control panel that allows for intuitive operation.

Finally, the 3970 model is a versatile choice for those seeking a balance of size and efficiency. It offers a compact design without sacrificing performance, making it ideal for smaller rooms. The 3970 includes the same advanced air control system found in larger models, ensuring efficient combustion and heat output.

In summary, Vermont Casting’s 4065, 4075, 4070, 3976, and 3970 models exemplify the perfect blend of traditional craftsmanship and modern technology. With exceptional features such as catalytic combustors, advanced air management, and customizable designs, these stoves offer both aesthetic appeal and functional efficiency, meeting a range of heating needs for contemporary homeowners.
Top Page Image Contents