Vermont Casting 4080, SDVR, PDV20: 3920, 4075, 3930 Thermostat Connection, Install the Front Plate

Page 24

Pinnacle & Stardance Direct Vent - Rear Vent Gas Heaters

Switch

Existing

Assembly

Holes

 

Screws

ST315

 

Fig. 40 Attach switch assembly to rear shroud.

 

TPTH

TPTH

PILOTADJ

ST228

Thermostat Connection

(Optional) R Models Only

Use only a thermostat rated for 500 - 750 millivolts.

Check the table below for the appropriate gauge thermostat wire to use for the length of lead required in your installation.

Thermostat

 

Wire / Gauge

Maximum Run

18

40 feet

20

25 feet

22

16 feet

1.Install the wall thermostat in the desired location and run the wires to the stove location. Terminate these leads with 1/4” female connectors.

2.Connect the thermostat wires to the valve. (Fig. 41)

This completes assembly of the PDV20 and SDVR stove.

Fig. 41 Attach switch wires to valve.

Install the Front Plate

Grasp the Front Plate and lift it into position, engaging the two steel tabs at the upper corners behind the adjacent bosses in the Side Plates. (Fig. 42) Seat the Front against the Sides so that the tabs at the bottom lip engage with the notches in the edge of the stove base.

When properly installed, the bottom of the Front Plate cannot be pulled away from the sides without also lifting it up.

If you are installing optional Warming Shelves, do so now, according to the instructions supplied with that kit.

Bottom Tabs

 

Engage Notch in Base

ST407

 

Fig. 42 Install Stove Front.

24

20007066

Image 24
Contents Pinnacle & Stardance Direct Vent, Rear Vent Gas Heater Table of Contents Installation & Operating Instructions Stove Dimensions Pinnacle Direct Vent Gas Heater Stove Dimensions Stardance Direct Vent Gas HeaterClearance Requirements Minimum Clearances to Combustible MaterialsGas Specifications Mantel Clearances Hearth RequirementsGas Inlet and Manifold Pressures Input Model Fuel Gas Control BTU/hHigh Elevations Horizontal TerminationVertical Termination Vent Termination ClearancesLocation of Vent Termination Canadian Installations1 US Installations2 General Venting Information Termination LocationTermination Clearances Vent Components Installation Install Optional Fan Kit #2960/FK28Fan Kit Contents Unpack the StoveVenting System Assembly Direct Vent For U.S. installations The venting system mustFor Canadian installations The venting system must General InformationPDV20 with Rear Vent Kit 7TFSRSK installation Through Side Wall Vent Termination Below GradeSide Wall Termination Assembly Install inner starter pipe and inner elbowDetermine the vertical pipe length Vertical Through the Roof Vent Assembly ³⁄₈ x 9³⁄₈ 240 x 240mmVertical Through Existing Chimney Fireplace Vent Termination ClearancesFireplace Vent System Fireplace Installation Requirements PDV20 Fireplace Installation Requirements Sdvr Complete the Assembly Install ON/OFF Switch R Models onlyConnect the Gas Supply Line Burner InformationInstall the Front Plate This completes assembly of the PDV20 and Sdvr stoveThermostat Connection Use only a thermostat rated for 500 750 millivoltsInstall the Log Set LogsFlame & Temperature Adjustment Flame CharacteristicsOperation Your First FireCorrect pilot flame pattern. PSE Pilot Lighting And Operating Instructions To Turn Off Gas To HeaterWhat to do if YOU Smell GAS Troubleshooting / Honeywell #8420 Gas Control System Symptom Possible Causes Corrective ActionShut Off Procedure Transmitter Operation Off ModeOn Manual Mode Delay Timer ModeAuto Mode Fan Override During Auto ModeChange Between F/C Temperature Units Disable Thermostat FunctionLocal Path Conversion Precautions Conversion ProcedureAuto Path Fuel Conversion InstructionsModels 3920, 3930, 4065, 4070 R Models Only Pilot TypeModels 3960, 3970, 4075, 4080 RF Models Only All ModelsConversion to Natural Gas Input BTU/h Conversion to LP Input BTU/hMaintenance Gasket Replacement Inspect the Vent System AnnuallyCheck the Gas Flame Regularly Stove Disassembly Wiring DiagramsPinnacle PDV20 / Stardance Sdvr Direct Vent/Rear Vent Description PDV20 SdvrFuel Conversion Kits Optional Accessories Remote ControlsFan Kits Screen KitProduct Covered by this Warranty If Warranty Service is NEEDED…CFM Specialty Home Products

3966, 4080, 3926, 3936, 3960 specifications

Vermont Casting is renowned for its craftsmanship and quality in the hearth industry, particularly with its range of wood and gas stoves. Among its standout models are the 4065, 4075, 4070, 3976, and 3970. Each of these models presents unique features and advanced technologies that cater to a variety of heating needs and preferences.

The Vermont Casting 4065 model is designed with efficiency and usability in mind. Its advanced air management system allows for precise control over combustion, ensuring that homeowners enjoy a longer burn time while minimizing emissions. The large glass door provides an excellent view of the fire, making it a centerpiece in any room. Additionally, the 4065 is built from heavy-duty cast iron, which not only enhances durability but also retains heat longer.

Moving on to the 4075 model, this stove offers an impressive heat output, making it suitable for larger spaces. The 4075 incorporates a unique catalytic combustor, which boosts efficiency by enabling cleaner burns and reducing smoke output. This model also features a user-friendly ash removal system, simplifying maintenance and enhancing user experience.

The 4070 model stands out with its modern design and customizable options. It comes in various colors and finishes, allowing homeowners to tailor it to their interior design style. Like the other models, it emphasizes efficiency with a built-in heat exchanger, maximizing heat transfer to the surrounding space and ensuring optimal comfort.

The Vermont Casting 3976 is a powerhouse of innovation. Equipped with Vermont Casting’s signature cast iron construction, it provides exceptional heat retention and distribution. It features a powerful blower option that can be added for enhanced heat circulation, making it ideal for larger homes or open floor plans. The 3976 also boasts an easy-to-use control panel that allows for intuitive operation.

Finally, the 3970 model is a versatile choice for those seeking a balance of size and efficiency. It offers a compact design without sacrificing performance, making it ideal for smaller rooms. The 3970 includes the same advanced air control system found in larger models, ensuring efficient combustion and heat output.

In summary, Vermont Casting’s 4065, 4075, 4070, 3976, and 3970 models exemplify the perfect blend of traditional craftsmanship and modern technology. With exceptional features such as catalytic combustors, advanced air management, and customizable designs, these stoves offer both aesthetic appeal and functional efficiency, meeting a range of heating needs for contemporary homeowners.