Kobe Range Hoods CH2748SQB, CH2730SQB, CH2736SQB, CH2742SQB installation instructions

Page 17

-If necessary, attach two rubber stands (provided) with two (4x8 mm) screws (provided) to the back of the hood.

-Attach the hood-mounting bracket to the back of the hood with nine (3/16" x 3/8") screws (provided) as shown in Figure 25.

Hood Installation

CAUTION: If required to move the cooking range to install the hood, turn OFF the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE.

1.Using references on Table 2 and measurements on page 22-23, mark the leveling point of the hood. Position two mounting screws (not provided) on the wall, leaving 1/8” away from the wall as shown in Figure 26.

Mounting

Screws

Figure 25

Figure 26

2.Use aluminum or steel pipe to connect the exhaust opening at the rear of the hood to the ductwork. Use duct tape to make all joints secure and air tight.

3.Align hood-mounting bracket to the two screws on the wall and hook hood into place. Tighten screws to secure hood to the wall. CAUTION: MAKE SURE THE HOOD IS SECURE BEFORE RELEASING.

Duct Cover Installation

4.Mark the position of the duct cover-mounting bracket. Use calculation E from Table 2 for references. Attach and secure duct cover-mounting bracket with two screws (not provided). Refer to Figure 27. NOTE: Inner duct cover will cover the mounting bracket.

5.Connect electrical wires. Refer to “Wiring to Power Supply” on page 16.

6.Slide the inner duct cover up 2 inches before sliding the entire duct cover onto the hood. Refer to Figure 28.

15

Image 17
Contents Kobe Brand Range Hood English English ContentsImportant Safety Instructions Page Components of Package For Wall Mount with Optional Duct Cover InstallationFor Under the Cabinet Safety Warning Under the Cabinet Installation TOP Vent Page Under the Cabinet Installation Rear Vent Page Wall Mount Installation TOP Vent Page Page Wall Mount Installation Rear Vent Page Page Wiring to Power Supply Operating Instructions Cleaning Hood Surface Maintenance Safety WarningReplacing Light Bulb CH2748SQB 258W / 2.41A SpecificationsFor Stand Alone with Optional Duct Cover Measurements & DiagramsHood-Mounting Bracket Duct Cover-Mounting Bracket Model NO. CH2730SQB CH2736SQB CH2742SQB CH2748SQB Parts ListModel NO. CH2730SQB CH2736SQB Model NO. CH2742SQB CH2748SQB Circuit Diagram Model NO. CH2742SQB CH2748SQB Issue Possible Cause Solution Trouble ShootingClaims will not be Accepted After the Allocated Days DisclaimerWarranty Certificate WarrantyTWO-YEAR Warranty Service Period ConditionsImplied WARRANTIES/STATE LAW ServiceConsequential Damage Record the Following Information for Your Record Product RegistrationTable DES Matières FrenchMesures DE Sécurité Importantes SVP Lire Cette Section Attentivement Avant LinstallationQue faire en cas dun incendie de graisse sur la cuisinière Contenu DE LA Boîte Modèle Ilot Avec Couvre Conduit Optionel Installation Sous LE CabinetIlot AvertissementSous LE Cabinet Installation Sous LE Cabinet Conduit Supérieur Installation de la hotte Installation Sous LE Cabinet Conduit Arrière Trou Diamètre Préparation avant Installation Installation Modèle Ilot Conduit SupérieurInstallation de la hotte Installation avec couvre- conduits Installation Ilot Conduit Arrière Adaptateur rectangulaire sortie arrière Photo Installation avec couvre- conduit Connexion à lalimentation dénergie Mode Demploi Pour Nettoyer LES Surfaces DE LA Hotte ENTRETIEN- NettoyageRemplacement Dune Ampoule Consommation SpécificationsPour Modèle Ilot Avec Couverture DE Conduit Facultative Mesures et DiagrammesSupport de fixation hotte Support de fixation couvre-conduit CH2736SQB CH2742SQB CH2748SQB Liste DES PiècesCH2730SQB CH2742SQBCH2748SQB Diagramme DES Circuits Nos de modèles Problème Cause probable Avis DE NON-RESPONSABILITÉ Période DE Garantie DE Deux 2 ANS GarantieCertificat DE Garantie Garanties Tacites / Réglementation ServiceDommages Indirects Inscrire LES Renseignements Suivants Pour NOS Dossiers Enregistrement DU ProduitSpanish Advertencia Para Reducir EL Riesgo QUE Ocurran Lesiones Instrucciones Importantes DE SeguridadPrecaución Qué Hacer si Siente Olor a GasCaja de la Campana de Extracción Separado Componentes DEL PaquetePara Instalación Debajo DEL Gabinete Tabla InstalaciónDebajo DEL Gabinete Advertencia DE SeguridadInstalación Debajo DEL Gabinete Ventilación Superior Agujero de un de diámetro1 Instalación Debajo DEL Gabinete Ventilación Posterior Figura Instalación Independiente Ventilación Superior Figura Figura Instalación Independiente Ventilación Posterior Figura Figura Cableado Hacia la Fuente de Alimentación Instrucciones DE Operación Mantenimiento Advertencia DE Seguridad Para Reemplazar el Foco Especificaciones Para Debajo DEL Gabinete Medidas Y DiagramasSoporte de Montaje de la Campana Modelo no CH2730SQB CH2736SQB CH2742SQB CH2748SQB Listado DE PiezasModelo no CH2730SQB CH2736SQB Modelo no CH2742SQB CH2748SQB Diagrama DE Circuito Modelo no CH2742SQB CH2748SQB Problema Posible Causa Solución Cláusula DE Exención Certificado DE Garantía GarantíaPeriodo DE Servicio DE LA Garantía DE DOS Años CondicionesServicio Daños EmergentesGarantías IMPLÍCITAS/LEY Estatal Escriba LA Siguiente Información Para SUS Archivos Registro DEL Producto100