Empire Comfort Systems CIBV-30-20 Glass Cleaning, General Glass Information

Page 20

MAINTENANCE (continued)

Glass Cleaning

It will be necessary to clean the glass periodically. During start-up condensation, which is normal, forms on the inside of the glass and causes lint, dust and other airborne particles to cling to the glass surface. Also initial paint curing may deposit a slight film on the glass. It is therefore recommended that the glass be cleaned two or three times with a non-abrasive household cleaner and warm water (we recommend gas fireplace glass cleaner). We do not recommend using packaged spray type household glass cleaner. After that the glass should be cleaned two or three times during each heating season depending on the circumstances present.

General Glass Information

Only glass approved for use in Empire Comfort Systems, Inc. fireplaces may be used for replacement. The glass replacement should be done by a licensed or qualified service person.

WARNING:

1.The use of substitute glass will void all product warranties.

2.Care must be taken to avoid breakage of the glass.

3.Under no circumstances should this appliance be operated without the glass front or with a broken glass front. Replacement of the glass (with gasket) as supplied by the manufacturer should be done by a qualified service person.

4.Do not abuse the glass by striking or hitting the glass.

WARNING: Do not use abrasive cleaners on glass. Do not attempt to clean glass when glass is hot.

Failure to follow these warnings could cause a serious safety issue to the operator, such as fire or other serious conditions.

Glass Assembly Replacement

1.Remove casting top from casting.

2.Remove casting front from casting.

3.Lower valve cover on firebox.

4.Release two door latches at bottom of firebox.

5.Grasp bottom of glass frame, lift glass frame upward in order to release glass frame from lip on top of firebox.

6.Place glass frame assembly on a non-abrasive surface. The exterior of the glass frame assembly should be facing the non-abrasive surface.

7.Insert a putty knife between glass and bottom corners on frame. Carefully separate glass from frame.

8.Use putty knife to remove silicone and gasket material from frame. Surface of frame must be clean and dry.

9.At each corner of frame apply (2) three inch beads of high temperate (orange) silicone.

10.With thin gasket on glass facing silicone on frame, insert glass into frame. Carefully press the glass onto frame in order to have contact between glass and silicone.

11.Allow silicone to set-up for an adequate time.

12.Align and place top of glass frame over lip on top of firebox. Grasp bottom of glass frame, push inward and place glass frame onto firebox.

13.Attach two door latches to bottom of firebox.

14.Replace casting front onto casting.

15.Replace casting top onto casting.

16.Replacement of glass assembly is completed.

Figure 22

Page 20

15627-5-0807

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Installation Instructions Table of Contents Important Safety Information This is a Heating ApplianceSafety Information for Users of LP-GAS LP-GAS Warning OdorIntroduction Specifications CIBV-30Installing a New Main Gas Cock GAS SupplyRecommended Gas Pipe Diameter Checking Manifold PressureInstallation on Rugs and Tile ClearancesDetailed Instructions Follow Assembly of Stove CastingAppliance Hardware Package Assembly of Stove Casting 15627-5-0807 Parts List Optional Stone Inlay InstallationInstallation of Optional Stone Inlay Wire Channel Installation LOG PlacementVent Safety Shutoff System Operating GuidelinesVenting VentingLiner and Insulated Liner Insulated Vent Enclosure FigureFor Your Safety Read Before Lighting Lighting InstructionsPilot Flame Characteristics Main Burner Flame CharacteristicsAir Shutter Adjustment Cleaning the Log Set and FireboxWiring Cleaning Procedure MaintenanceMaintenance & Service Instructions General Glass Information Glass CleaningGlass Assembly Replacement Troubleshooting Frequent pilot outage problemPilot and main burner extinguish while in operation Glass sootsHOW to Order Repair Parts Parts List for CIBV-30-20Parts View for CIBV-30-20 Parts List for Stove Casting Parts View for Stove Casting Optional Blower Installation Instructions Installing Optional CIB-2 BlowerRefer to Wire Channel Installation, Fan ControlCleaning WiringBlower Motor Index Part No. No. DescriptionFAX

CIBV-30-20 specifications

Empire Comfort Systems CIBV-30-20 is a versatile and efficient heating solution designed to meet the needs of both residential and commercial spaces. This direct vent gas fireplace boasts an array of features that make it a popular choice for those looking to enhance their indoor environment with warmth and style.

One of the main features of the CIBV-30-20 is its sleek and contemporary design. The fireplace comes with a clean-faced front that allows for a seamless integration into any decor. Its compact size, with a 30-inch width, makes it suitable for various settings, from cozy living rooms to larger commercial spaces. The large viewing area maximizes the sight of the flames, providing an inviting ambiance and a warm atmosphere.

Performance is a key characteristic of the CIBV-30-20. It operates using natural gas or propane, allowing users to choose the fuel type that best fits their needs. With an impressive heat output of up to 25,000 BTUs, this fireplace efficiently heats the room, ensuring comfort during the cold months. Empire Comfort Systems has engineered the fireplace to deliver consistent and reliable performance, making it an ideal choice for year-round use.

Another significant technology integrated into the CIBV-30-20 is its direct vent system. This feature allows for safe and efficient venting, as it draws air from the outside to fuel the fire, thus eliminating the risk of indoor air pollution. The balanced flue technology ensures that combustion gases are vented outside, maintaining good air quality indoors.

In terms of controls, the CIBV-30-20 is equipped with a reliable millivolt system, which allows for easy operation without the need for electricity. For added convenience, optional remote control kits are available, enabling users to adjust flame height and heat levels from a distance.

The Empire Comfort Systems CIBV-30-20 also prioritizes efficiency. With an efficiency rating of up to 75%, it provides substantial warmth while minimizing energy consumption, making it an eco-friendly heating option.

In summary, the Empire Comfort Systems CIBV-30-20 combines modern aesthetics with advanced heating technology. Its features, including direct vent capability, high heat output, and efficient performance, make it a standout solution for anyone seeking a reliable and stylish heating appliance. Whether for home or business use, the CIBV-30-20 is designed to deliver warmth, comfort, and a welcoming ambiance.
Top Page Image Contents