Hearth and Home Technologies BE-36-C manual Positioning the Logs

Page 42

D. Positioning the Logs

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions.

Log Set Assembly: LOGS-BE-36-C

Models: BE-36-C

1

2

3

TAB TAB

Carefully remove the logs from the packaging. CAUTION: Logs are fragile!

1

2

LOG #1 (SRV397-701):Place log #1 so the notch on the right side rests on the right grate tine. The left side of log #1 should rest on the pilot bracket. Slide the log to the rear until it touches the rear tab.

3

LOG # 2 (SRV397-702):Place log #2 on the left side of the grate in front of log #1. The left edge of log #2 should touch the firebox. The right edge of log #2 should be pushed back until it touches the tab. NOTE: It may be necessary to tilt log #1 back slightly while placing log #2 on the grate.

LOG # 3 (SRV397-703):Place log #3 on the right side of the grate in front of log #1. The right edge of log #3 should touch the firebox while the rear lines up with the left log. The left edge of log #3 should rest on the grate and log #1 as shown.

397-935B 6/04

42

Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07

Page 41 Page 43
Image 42
Page 41 Page 43
Contents BE-36-CIPI What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Inspect Appliance and Components Design and Installation ConsiderationsGetting Started Tools and Supplies NeededFraming and Clearances Selecting Appliance LocationModels Constructing the Appliance Chase ClearancesMantel Projections Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesSee .4 for specific clearances Alcove Applications Minimum Clearances for TerminationUse of Elbows Vent Information and DiagramsVent Table Key Measuring StandardsUse of Flex Vent Vent Diagrams Top Vent Horizontal Termination One ElbowTwo Elbows Top Vent Horizontal Termination Three Elbows Top Vent Vertical Termination No Elbows V1 = 44 ft. Max .4 m Baffle InstructionTop Vent Vertical Termination Two Elbows Three Elbows Minimum H1 MaximumPage Rear Vent Horizontal Termination- Two elbows Rear Vent Horizontal Termination- Three elbowsRear Vent Horizontal Termination- One elbow Rear Vent Horizontal Termination Two elbowsRear Vent Horizontal Termination- Three elbows Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Non-Combustible Wall PenetrationVertical Penetration Framing Installing the Ceiling FirestopInstalling Attic Shield 10 IN. X 10Appliance Preparation Choosing the Top or Rear VentRear Vent Cut the metal retaining band and fold the sides outSecuring and Leveling the Appliance Fire Risk Prevent contact with sagging, loose insulationAttaching Vent to the Firebox Assembly Installing Vent PipeAssembly of Vent Sections DVP Pipe only Assembling Pipe SectionsAssembling Minimum Installations MI Sections Assembling DVP-12A Slip SectionsSecuring the Vent Sections Vertical Sections Disassembly of Vent SectionsDVP Pipe only Horizontal SectionsAttach the First Vent Component to Starting Collars Assembly of Vent Sections SL Series Pipe onlyInstall Support Brackets Continue Adding Vent ComponentsInstalling the Horizontal Termination Cap Heat Shield Requirements for Horizontal TerminationFire Risk. Explosion Risk Installing Roof Flashing and Vertical Termination Cap Assembling and Installing Storm Collar 20 Assembling the Storm Collar Around the PipeGas Pressures Gas InformationFuel Conversions Gas Connection Pressure Natural Gas PropaneHigh Altitude Installations Recommendation for Wire Connecting to the ApplianceElectrical Information Standing Pilot Ignition System Wiring Intellifire Ignition System WiringJunction Box Installation Wall Switch Installation for Fan OptionalFinishing Facing MaterialSee for combustible/non-combustible definitions Accessories Appliance SetupClean the Appliance Remove Shipping MaterialsLog Set Assembly LOGS-BE-36-C Models BE-36-C Positioning the LogsReplacing Glass Assembly Glass AssemblyRemoving Glass Assembly Shutter SettingsOperating Instructions Before Lighting ApplianceTurn on all electric power to the appliance Lighting ApplianceFor Your Safety Read Before Lighting Instructions Standing Pilot IgnitionFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionIntellifire Ignition System Sympton Possible Cause Corrective ActionSure must not exceed 14 in. W.C Maintaining and Servicing Appliance Inspect Maintenance Tasks Recommend addition of screen if one is not presentAppliance Dimension Diagram Reference MaterialsVent Components Diagrams DVP45 45 ElbowDVP-TRAP 367 mm 24-5/8 625 mm13-1/4 13-7/8 352 mm 241 mmVertical Termination Cap 184 mm 12-1/2 318 mm 133 mm 98 mm10-1/2 Vertical Termination Cap High windSL Series Vent Components Pipe Length/InchesService Parts Log Set AssemblyStanding Pilot ÎC. Service Parts List BE-36-CAdditional service part numbers may appear on the following IPI SystemService Parts BE-36-C Standing Pilot Valve AssemblyIPI Valve Assembly BE-36-CIPILimited Lifetime Warranty Hearth & Home TechnologiesContact Information
Related manuals
Manual 37 pages 30.79 Kb

BE-36-C specifications

Hearth and Home Technologies, a leader in innovative heating solutions, offers two remarkable gas fireplaces: the BE-36-CIPI and BE-36-C. Both models are designed to deliver efficient heating, aesthetic charm, and user-friendly features, making them ideal for modern living spaces.

The BE-36-CIPI is a direct vent fireplace that provides the warmth of a traditional fire without the hassle of wood. One of its most notable features is its contemporary design, featuring clean lines and a wide viewing area. This model comes with an impressive heat output, ensuring that spaces remain comfortably warm during chilly seasons. The BE-36-CIPI incorporates innovative technologies like the IntelliFire™ ignition system, which promotes energy efficiency by providing reliable performance while minimizing fuel consumption.

Moreover, the fireplace's advanced burner system creates a stunning flame pattern and realistic look, enhancing the ambiance of any room. With customizable options, homeowners can choose different media types, such as ceramic logs or contemporary stones, allowing for personal expression in their décor.

On the other hand, the BE-36-C model offers similar features but with its unique twist. This model is characterized by its traditional aesthetic appeal, making it an excellent choice for those who prefer a classic look with modern convenience. The BE-36-C also utilizes the IntelliFire™ system, ensuring efficiency and ease of use. With a versatile design, this fireplace can fit into various style preferences, from rustic to modern.

Both models come equipped with optional heat management systems, allowing for effective temperature regulation. This feature is particularly useful for maintaining a comfortable environment without overheating the space. The fireplaces are also designed with safety in mind, adhering to strict safety standards and offering numerous safety features like a safety pilot and tempered glass doors.

In conclusion, Hearth and Home Technologies’ BE-36-CIPI and BE-36-C gas fireplaces present an ideal blend of aesthetics, efficiency, and advanced technology. Whether opting for the contemporary style of the BE-36-CIPI or the classic allure of the BE-36-C, homeowners are guaranteed to enjoy a superior heating experience that complements their home’s design while providing warmth and comfort.
Top Page Image Contents