Zanussi ZKG5530 user manual If a moulded plug is fitted, Connecting to gas supply

Page 30

The wire, which is coloured blue, must be connected to the terminal, which is marked with the letter N or coloured black.

The wire, which is coloured brown, must be connected to the terminal, which is marked with the letter L or coloured red.

Ensure that the cable does not become trapped when pushing the appliance into position.

If a moulded plug is fitted.

In the event of replacing a fuse in the plug supplied a 3 amp ASTA approved fuse to B.S. 1362 must be fitted.

IMPORTANT!

The fuse cover must be refitted when changing the fuse. In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been obtained and fitted.

Connecting to gas supply

This appliance is designed to be installed with an appliance flexible connection only.

Supply piping should not be less than R3/8. Connection is made to the Rc ½ (½” B.S.P.) female threaded entry pipe located just below the hob level on the rear left hand side of the appliance.

IMPORTANT!

ONLY LIQUID SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED I.E.: DO NOT USE P.T.F.E. SEALANT TAPE.

Carry out a gas tightness test after connecting to the gas supply.

The gas bayonet connector must be fitted in the shaded area indicated.

30

Take into account that it must be possible to pull the appliance forward sufficiently. Ensure the hose does not become trapped when pushing the appliance into position.

IMPORTANT!

FLEXIBLE TUBING USED MUST COMPLY WITH BS.669 CURRENT EDITION.

Fitting the stability chain

It is recommended that if the appliance is to be installed with a flexible supply pipe, a stability chain be fitted and is available from your supplier (see Important Safety Requirements). These instructions should be read in conjunction with any leaflet packed with the stability chain.

1.Place the appliance in its intended position and level appliance.

2.Mark a position 100mm from the top of the rear right hand corner.

3.Measure down 150mm from this point. This gives the position of the wall anchor point for the stability chain.

Image 30
Contents ZKG6040ZKG5530WFN Contents During use InstallationChild safety Make sure that a stability chain is fittedCleaning and maintenance Product description Controls and their functionsCondensation and steam Before using the applianceRating plate CookwareGrill and oven furniture To turn off any burner HobTo light the hob burners Hob ignition works by means of an electric spark systemThings to note Hints and tipsDo not overfill pans or they will boil over To turn off the grill Using the grillGrill Fully open the door before lighting the grillGrill pan and handle Button onSlide the handle Towards the right Grilling chart Food should be turned over during cooking as requiredHeat zones Using the main ovenMain oven To fit the main oven shelvesTo turn the main oven off Main oven cooking chart PosMain oven cooking chart Roasting chart Cooking timeUsing slow cook Slow cookFood preparation slow cooking General pointsThaw thoroughly before cooking Cleaning the outside of the appliance Care and cleaningCleaning materials Cleaning the hobCleaning the grill and oven furniture Cleaning the grillCleaning the doors To remove the inner glassTo replace the inner glass To clean the inner glass door panels Replacing an oven light bulbType of bulb required is a 300C 25 watt small Edison Screw Troubleshooting ProblemTechnical data DimensionsHeat Input Heat input 0kW 9kW 3412 Btu/h 6483 Btu/h070 096 120Installation instructions Provision for ventilationLocation of appliance For your safetyMoving your appliance ApplianceBy the earth symbol or coloured green or green and yellow Leveling the applianceIf the fitted plug is removed Connecting to gas supply If a moulded plug is fittedFitting the stability chain Checking the hob Pressure testingChecking the grill Checking the main ovenEnvironment At the end of the appliances lifeGuarantee / Customer care Standard guarantee conditionsPage Page 349153201 04/2007 3349165902