Zanussi ZKC6040 user manual Installation instructions, Connecting to the electricity supply

Page 35

Installation instructions

WARNING!

This appliance must be earthed

•If your appliance has been damaged in transit, contact your supplier immediately. Do not attempt to install it.

•Your appliance left the factory fully packaged to protect it from damage. If it is delivered without packaging and damage has occurred, the manufacturer cannot accept responsibility. Contact your supplier for advice.

•Once the packaging has been removed the appliance should only be moved by hand. Do not use a sack barrow or any other aid to lift the appliance as damage may occur.

•To move the appliance, open the oven door and lift the appliance by holding inside the top of the compartment.

•This is a type Y appliance, which means it is freestanding and can be fitted with cabinets on one or both sides. It may also be fitted in a corner setting.

•Sidewalls, which are above hob level, should be protected by heat resistant non- combustible material and must not be nearer than 40mm to the hob side.

•A nominal air gap of 2mm at either side of the appliance is required to enable the appliance to be moved into position.

•Always ensure an air gap is maintained at hotplate level. Tiles or other forms of deep wall covering should not obscure this gap.

•Overhanging surfaces or a cooker hood should be a minimum of 685mm above the hob.

40 min

685 min

22

•It is important to ensure that the appliance is level after installation. Levelling feet are fitted to the appliance to accommodate uneven floors.

Connecting to the electricity supply

WARNING!

This appliance must be earthed. Do not earth this appliance to gas supply piping. Connect to 230 - 240V AC supply only.

•Connection to the electricity supply must be carried out by a qualified electrician/competent person.

•The electrical connection should be made using a double pole isolating switch (cooker socket) with at least 3mm contact separation in all poles. The cable must have conductors of sufficiently high cross- sectional area to prevent overheating and deterioration.

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents User Manual Cooker Contents During use Important safety instructionsInstallation Child safetyExtreme care must be taken when using a ceramic hob scraper Cleaning and maintenanceControls and their functions Product descriptionCookware Before using the applianceRating plate Condensation and steamGrill and oven furniture To set the countdown Electronic timerTo set the time of day Neon flashes To cancel the countdownCountdown indicator Press the selectorThat the correct time of day is displayed To set the timer to switch on and off automaticallyTo set the timer to switch off only Return to the time Day Cook time indicatorIndicator neon will Controls Continue to flash for a Cook timeRecommended saucepans Using the hobHints and tips when using the hob HobGrill Hot hob indicatorUsing the grill Grill settings are as followsSlide the handle Towards the right Grill pan and handleTo Remove. Press Button onFood should be turned over during cooking as required Grilling chartHints and tips To fit the top oven shelf Using the top ovenTop oven Hints and tips Main oven Things to note Oven cooking chart Oven cooking chart 160 180 C Roasting chartDefrost Using defrostTop oven light Using main oven lightUsing top oven light Main oven lightSlow cook Using slow cookThaw thoroughly before cooking Food preparation slow cookingGeneral points Care and cleaning Avoid the use To reduce marking of the hobHousehold detergents and bleaches Cleaning the doorsAerosol cleaners must not be used on Stay- clean surfaces Inner door glass is removable for cleaningMain Oven To remove the glassTo replace the door glass Top OvenType of bulb required is a 300C 25 watt small Edison Screw Replacing an oven light bulbTimer does not work Oven is not cooking evenly TroubleshootingOven light fails to illuminate Oven fan is noisy This appliance must be earthed Installation instructionsConnecting to the electricity supply Ensure all screws are securely tightened Ensure that the cover is securely fastenedSwitching on the time display Technical dataEnergy save mode Switching off the time displayStandard guarantee conditions Guarantee / Customer carePage 349143001
Top Page Image Contents