Sherwood RD-8504 manual Adjusting the current channel level, Press the Channel Level button

Page 25

RD-8504(G)_ENG_091217:RD-8504(G) 2009-12-21 오￿ 11:36 페이지 25

Adjusting the current channel level

•After adjusting each channel level with test tone, adjust the channel levels either according to the program sources or to suit your tastes.

•You can adjust the current channel levels as desired. These adjusted levels are just memorized into user’s memory ("CAL"), not into preset memory("MOVIE" for movieo source, "MUSIC" for music source).

1.Press the CHANNEL LEVEL button.

• Then the memory mode ("CAL", "MOVIE", etc) is displayed for several seconds.

• When the memory mode or channel level disappears, press this button again.

ENGLISH

2. Select the desired channel.

• Each time these buttons are pressed, the corresponding channel is selected as follows:

→ CAL (or MOVIE, etc.) ↔ FL ← C ← FR ← SR ←

→ <LFE> ↔ SUB ↔ SL(↔SB) or (↔SBL ↔ SBR) ←

DTS LFE or Dolby Digital LFE

( ): Possible depending on whether the surround back channel is set to "2 Channel" or "1 Channel (Left)".

< >: Possible only when the digital signals from Dolby Digital, DTS, Dolby TrueHD or DTS HD program sources that include LFE signal are input.

• Depending on the speaker settings("No", etc.) and surround mode, etc., some channels cannot be selected.

• When the SPEAKER button is set to off, only the Front Left, Front Right(and LFE) channels can be selected.

3. Adjust the level of the selected channel as desired.

• The LFE level can be adjusted within the range of -10 ~ 0 dB and other channel levels within the range of -15 ~ +15 dB.

• In general, we recommend the LFE level to be adjusted to 0 dB.(However, the recommended LFE level for some early DTS software is -10 dB.) If the recommended levels seem too high, lower the setting as necessary.

4. Repeat the above steps 2 and 3 to adjust each channel level.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents RD-8504 Do not ExPOSE this Appliance to Rain or mOISTURE Introduction220 240 Contents System Connections Connecting AntennasVideo conversion Connecting Video COmPONENTSComponent video input default settings *2 Connecting Audio COmPONENTSHDmI High Definition multimedia Interface connection *1 Copyright protection systemDigital input default settings Connecting ExTERNAL INSSurround back speakers Connecting SPEAkERSFront Bi-Amp Connections Speaker placement Connecting for SYSTEm Control Connecting ROOm 2 OutsFluorescent Display Front Panel ControlsFront AUx in JACk Setup mIC JACkVideo 4 in JACkS Universal Remote Controls Stop Function Table of the Numbered ButtonsReMote contRoL oPeRAtIon RAnGe Repeat the above steps 1 to 4 for each of your Components Entering a setup codeRemoving a punch-through function Using a punch-through functionRemoving all punch-through functions Operating a macro function Programming a macro functionTo remove a macro program To change a macro programSwitch the speakers on Standby mode, turn the power onOperations Before operationAdjust the overall volume Listening with headphonesMuting the sound Press the Audio Assign buttonSurround modes Hall TheaterStadium RoomEnjoying Surround Sound Enter the test tone mode Adjusting each channel level with test toneCancel the test tone function To cancel the surround mode for stereo operationAdjust the level of the selected channel as desired Adjusting the current channel levelRepeat the above steps 2 and 3 to adjust each channel level Press the Channel Level buttonRecalling the memorized channel levels Memorizing the adjusted channel levelsManual tuning Auto tuningAuto presetting Press the Tuning UP+/DOWN- buttons for more than 0.5 secondTuning to preset stations Manual presettingMEmORY BACkUP Function Repeat the above steps 1 to 3 to memorize other stationsTP search RDS searchFM mode FM mode, select the PTY search modePTY search While displaying PTY SRCH, select the desired program typeDubbing from video components onto Video To record audio signalsDigital Audio Recording with mD Recorder Adjusting the brightness of the fluorescent display Operating the sleep timerDisplaying the operation status Press the Room 2 button to enter the Room 2 mode When using the buttons on the front panelSet the selected mode as desired Start play on the component related to the Room 2 sourceAdjust the Room 2 volume When using the buttons on the remote control unitTurn on the Room 2 function Select the desired input as a Room 2 sourceSelect the desired menu using the Cursor UP/DOWN buttons OSD Menu SettingsTurn the menu screen on When selecting the InputSetup When selecting the System SetupWhen selecting the Sound Parameter When selecting the Speaker/Room EQ SetupBass Treble Setup menu flowVID1 CFG Setting the SYSTEm Setup When selecting the Subwoofer mode When selecting the AmP AssignWhen selecting the HDmI Audio Output When selecting the Tone ControlWhen selecting the momentary OSD When selecting the Cinema EQWhen selecting the Save/Recall Preparations When selecting the Auto SetupTo memorize the results, press the Cursor Right button When selecting the Room EQ Surround Surr Back Subwoofer When selecting the Speaker ConfigurationCenter Surround Surr Back When selecting the Speaker CrossoverAbout the speaker distance When selecting the Speaker DistanceWhen selecting the LFE When selecting the Channel LevelMemorizing the adjusted channel levels and recalling them When selecting the items other than Re-Name Setting the Input SetupWhen selecting the Component Assign When selecting the HDmI AssignWhen selecting the Audio Assign When selecting the Video modeWhen selecting the Video Scaling When selecting the Audio modeWhen selecting the AV Sync When selecting the HD Audio When selecting the Re-NameTo clear the name you entered To resume its factory input source nameWhen selecting the Input When selecting the RoomWhen selecting the Volume When selecting the Night mode When selecting the Dolby Pro Logic II musicWhen selecting the Detail Enhancement When selecting the PRePWhen selecting the Edge Enhancement When selecting the mosquito NRPROBLEm Troubleshooting GuideREmEDY Specifications Setup Code Table Inno HIT DOCK-VCR Otto Verand BD/DVD SAT AUX-USB/MD RD-8504
Related manuals
Manual 71 pages 21.87 Kb

RD-8504 specifications

The Sherwood RD-8504 is a powerful and versatile audio receiver designed for audiophiles and casual listeners alike. This unit elegantly combines modern technology with essential features, making it an attractive option for those seeking an immersive audio experience for their home theater or music listening setup.

At the heart of the RD-8504 is a robust amplifier capable of delivering 100 watts per channel, ensuring that even the most demanding speakers can operate at their peak performance. This power output allows for high volume levels without distortion, making it ideal for movies, music, and gaming. The receiver supports a wide range of speaker configurations, including 7.1 surround sound, enabling users to create a rich and enveloping audio environment.

One of the standout features of the Sherwood RD-8504 is its advanced Digital Signal Processing (DSP). This technology allows the receiver to provide multiple sound modes tailored to various content types, including movies, music, and sports. The DSP ensures that audio quality is maintained while optimizing the listening experience for different environments. Additionally, the receiver provides a built-in equalizer, which allows users to fine-tune sound settings to suit their personal preferences.

Connectivity is another strong suit of the RD-8504. The receiver is equipped with multiple HDMI inputs, making it easy to connect various devices such as game consoles, Blu-ray players, and streaming devices. The HDMI ARC feature also enables seamless audio transmission from compatible televisions. Beyond HDMI, the receiver includes analog and digital inputs, as well as USB connectivity for direct playback from external devices.

The RD-8504 also shines in its support for modern audio formats, including Dolby Digital and DTS, providing immersive surround sound that enhances the overall experience of films and music. Furthermore, it supports high-resolution audio formats, allowing users to enjoy lossless music playback and taking full advantage of today’s high-quality audio sources.

In terms of user interface, Sherwood has designed the RD-8504 with an intuitive layout and clear display. The front panel features easy-to-navigate buttons and a large LCD screen that provides essential information at a glance. The remote control offers comprehensive access to all features, enabling users to customize their listening preferences effortlessly.

In summary, the Sherwood RD-8504 receiver combines powerful amplification, advanced DSP technology, and extensive connectivity options to deliver an outstanding audio experience. Its blend of modern features and user-friendly design makes it an excellent choice for anyone looking to enhance their home entertainment system. Whether for a casual movie night or an immersive music session, the RD-8504 is poised to satisfy and impress.
Top Page Image Contents