Sherwood RD-8504 manual OSD Menu Settings, Turn the menu screen on

Page 36

RD-8504(G)_ENG_091217:RD-8504(G) 2009-12-21 오￿ 11:36 페이지 36

ENGLISH

OSD Menu Settings

•The OSD (On-Screen Display) menu is a setting menu that is displayed on the monitor TV and allows you to perform the setup procedures easily. In most situations, you will only need to set this once during the installation and layout of your home theater, and it rarely needs to be changed later.

The OSD menu consists of 6 main menus ; system setup, speaker/room EQ setup, input setup, multi room setup, sound parameter and advanced video . These menus are then divided up into various sub-menus.

■Notes:

• The OSD menu and the momentary OSD can be displayed via the HDMI MONITOR OUT only.

However, when the Video Scaling is set to HDMI Bypass and the video signals are input into the HDMI IN, the momentary OSD cannot be displayed via the HDMI MONITOR OUT. (For details, refer to “When selecting the Video Scaling” on page 53.)

•When performing the OSD menu operation, the corresponding operation status is displayed on the unit’s fluorescent display, too. Therefore, in such a case that the OSD menu cannot be displayed on your TV, perform the setup precedure, viewing the corresponding operation status on the fluorescent display. (For details on setup menu, refer to “Setup menu flow” on page 38.)

■Navigating through the OSD menu

•The explanations here assume you are using the buttons on the remote control when performing the OSD menu operation. However, you can use the buttons on the front panel as well.

The buttons on the front panel correspond to those on the remote control as shown below.

1. Turn the menu screen on.

EXIT

System Setup

NEXT

 

Speaker/Room EQ Setup

 

 

Input Setup

 

 

Multi Room Setup

 

 

Sound Parameter

 

 

Advanced Video

 

•The main menu will be shown.

•To turn the menu screen off, press this button again.

2. Select the desired menu using the CURSOR UP/DOWN buttons.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents RD-8504 Introduction Do not ExPOSE this Appliance to Rain or mOISTURE220 240 Contents Connecting Antennas System ConnectionsConnecting Video COmPONENTS Video conversionConnecting Audio COmPONENTS Component video input default settings *2HDmI High Definition multimedia Interface connection *1 Copyright protection systemConnecting ExTERNAL INS Digital input default settingsConnecting SPEAkERS Surround back speakersFront Bi-Amp Connections Speaker placement Connecting ROOm 2 Outs Connecting for SYSTEm ControlFront Panel Controls Fluorescent DisplaySetup mIC JACk Front AUx in JACkVideo 4 in JACkS Universal Remote Controls Function Table of the Numbered Buttons StopReMote contRoL oPeRAtIon RAnGe Entering a setup code Repeat the above steps 1 to 4 for each of your ComponentsUsing a punch-through function Removing a punch-through functionRemoving all punch-through functions Programming a macro function Operating a macro functionTo remove a macro program To change a macro programStandby mode, turn the power on Switch the speakers onOperations Before operationListening with headphones Adjust the overall volumeMuting the sound Press the Audio Assign buttonSurround modes Theater HallStadium RoomEnjoying Surround Sound Adjusting each channel level with test tone Enter the test tone modeCancel the test tone function To cancel the surround mode for stereo operationAdjusting the current channel level Adjust the level of the selected channel as desiredRepeat the above steps 2 and 3 to adjust each channel level Press the Channel Level buttonMemorizing the adjusted channel levels Recalling the memorized channel levelsAuto tuning Manual tuningAuto presetting Press the Tuning UP+/DOWN- buttons for more than 0.5 secondManual presetting Tuning to preset stationsMEmORY BACkUP Function Repeat the above steps 1 to 3 to memorize other stationsRDS search TP searchFM mode, select the PTY search mode FM modePTY search While displaying PTY SRCH, select the desired program typeTo record audio signals Dubbing from video components onto VideoDigital Audio Recording with mD Recorder Operating the sleep timer Adjusting the brightness of the fluorescent displayDisplaying the operation status When using the buttons on the front panel Press the Room 2 button to enter the Room 2 modeSet the selected mode as desired Start play on the component related to the Room 2 sourceWhen using the buttons on the remote control unit Adjust the Room 2 volumeTurn on the Room 2 function Select the desired input as a Room 2 sourceOSD Menu Settings Select the desired menu using the Cursor UP/DOWN buttonsTurn the menu screen on When selecting the System Setup When selecting the InputSetupWhen selecting the Sound Parameter When selecting the Speaker/Room EQ SetupSetup menu flow Bass TrebleVID1 CFG Setting the SYSTEm Setup When selecting the AmP Assign When selecting the Subwoofer modeWhen selecting the HDmI Audio Output When selecting the Tone ControlWhen selecting the Cinema EQ When selecting the momentary OSDWhen selecting the Save/Recall When selecting the Auto Setup PreparationsTo memorize the results, press the Cursor Right button When selecting the Room EQ When selecting the Speaker Configuration Surround Surr Back SubwooferWhen selecting the Speaker Crossover Center Surround Surr BackWhen selecting the Speaker Distance About the speaker distanceWhen selecting the Channel Level When selecting the LFEMemorizing the adjusted channel levels and recalling them Setting the Input Setup When selecting the items other than Re-NameWhen selecting the HDmI Assign When selecting the Component AssignWhen selecting the Audio Assign When selecting the Video modeWhen selecting the Audio mode When selecting the Video ScalingWhen selecting the AV Sync When selecting the Re-Name When selecting the HD AudioTo resume its factory input source name To clear the name you enteredWhen selecting the Room When selecting the InputWhen selecting the Volume When selecting the Dolby Pro Logic II music When selecting the Night modeWhen selecting the PReP When selecting the Detail EnhancementWhen selecting the Edge Enhancement When selecting the mosquito NRTroubleshooting Guide PROBLEmREmEDY Specifications Setup Code Table Inno HIT DOCK-VCR Otto Verand BD/DVD SAT AUX-USB/MD RD-8504
Related manuals
Manual 71 pages 21.87 Kb

RD-8504 specifications

The Sherwood RD-8504 is a powerful and versatile audio receiver designed for audiophiles and casual listeners alike. This unit elegantly combines modern technology with essential features, making it an attractive option for those seeking an immersive audio experience for their home theater or music listening setup.

At the heart of the RD-8504 is a robust amplifier capable of delivering 100 watts per channel, ensuring that even the most demanding speakers can operate at their peak performance. This power output allows for high volume levels without distortion, making it ideal for movies, music, and gaming. The receiver supports a wide range of speaker configurations, including 7.1 surround sound, enabling users to create a rich and enveloping audio environment.

One of the standout features of the Sherwood RD-8504 is its advanced Digital Signal Processing (DSP). This technology allows the receiver to provide multiple sound modes tailored to various content types, including movies, music, and sports. The DSP ensures that audio quality is maintained while optimizing the listening experience for different environments. Additionally, the receiver provides a built-in equalizer, which allows users to fine-tune sound settings to suit their personal preferences.

Connectivity is another strong suit of the RD-8504. The receiver is equipped with multiple HDMI inputs, making it easy to connect various devices such as game consoles, Blu-ray players, and streaming devices. The HDMI ARC feature also enables seamless audio transmission from compatible televisions. Beyond HDMI, the receiver includes analog and digital inputs, as well as USB connectivity for direct playback from external devices.

The RD-8504 also shines in its support for modern audio formats, including Dolby Digital and DTS, providing immersive surround sound that enhances the overall experience of films and music. Furthermore, it supports high-resolution audio formats, allowing users to enjoy lossless music playback and taking full advantage of today’s high-quality audio sources.

In terms of user interface, Sherwood has designed the RD-8504 with an intuitive layout and clear display. The front panel features easy-to-navigate buttons and a large LCD screen that provides essential information at a glance. The remote control offers comprehensive access to all features, enabling users to customize their listening preferences effortlessly.

In summary, the Sherwood RD-8504 receiver combines powerful amplification, advanced DSP technology, and extensive connectivity options to deliver an outstanding audio experience. Its blend of modern features and user-friendly design makes it an excellent choice for anyone looking to enhance their home entertainment system. Whether for a casual movie night or an immersive music session, the RD-8504 is poised to satisfy and impress.
Top Page Image Contents