Sherwood RD-8504 manual To memorize the results, press the Cursor Right button

Page 44

RD-8504(G)_ENG_091217:RD-8504(G) 2009-12-21 오￿ 11:36 페이지 44

Continued

ENGLISH

2. Press the CURSOR UP/DOWN buttons to select the Auto Setup, then press the CURSOR RIGHT button.

BACK Before starting the system,

NEXT

please plug the MIC. in using

 

the front panel jack.

 

<<Warning>>

 

The test tone is LOUD.

 

3. Press the CURSOR RIGHT button to start the auto setup procedure.

When the auto setup has been completed.

CANCEL COMPLETED APPLY

•Loud test tones are output successively and then if a series of auto setup procedure has been completed, "COMPLETED" will be displayed.

•To stop the auto setup procedure while performing it, press the CURSOR LEFT button.

In such a case that the auto setup procedure is stopped before "COMPLETED" is displayed, the results of each adjustment can not be memorized.

•If there may be a problem with speaker or microphone connection, error message will be displayed. In this case, turn off the power, check the connection and then retry the auto setup procedure.

■Notes :

•Because the test tones are loud, ensure there no infants or small children in the room.

•For best results, ensure the room is as quiet as possible during the auto setup procedure. If there is too much ambient noise, the results may not be satisfactory.

4. To memorize the results, press the CURSOR RIGHT button.

•Then the results are memorized and the Speaker/Room EQ Setup menu is displayed.

•When the CURSOR LEFT button is pressed to select “CANCEL”, the results are not memorized.

•Check the results on each setup menu(Speaker Configuration menu on page 46, Speaker Crossover menu on page 47, Speaker Distance menu on page 48 and Channel Level menu for "Calibrate" mode) on page 49).

•If the results are not satisfactory, you can retry the auto setup procedure or personalize your speaker setup and channel level setup by making the settings manually. (For details, refer to "When selecting the Speaker Configuration" on page 46, "When selecting the Speaker Crossover" on page 47, "When selecting the Speaker Distance" on page 48 and "When selecting the Channel Level" on page 49.)

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents RD-8504 220 240 IntroductionDo not ExPOSE this Appliance to Rain or mOISTURE Contents Connecting Antennas System ConnectionsConnecting Video COmPONENTS Video conversionConnecting Audio COmPONENTS Component video input default settings *2HDmI High Definition multimedia Interface connection *1 Copyright protection systemConnecting ExTERNAL INS Digital input default settingsFront Bi-Amp Connections Connecting SPEAkERSSurround back speakers Speaker placement Connecting ROOm 2 Outs Connecting for SYSTEm ControlFront Panel Controls Fluorescent DisplayVideo 4 in JACkS Setup mIC JACkFront AUx in JACk Universal Remote Controls Function Table of the Numbered Buttons StopReMote contRoL oPeRAtIon RAnGe Entering a setup code Repeat the above steps 1 to 4 for each of your ComponentsRemoving all punch-through functions Using a punch-through functionRemoving a punch-through function Programming a macro function Operating a macro functionTo remove a macro program To change a macro programStandby mode, turn the power on Switch the speakers onOperations Before operationListening with headphones Adjust the overall volumeMuting the sound Press the Audio Assign buttonSurround modes Theater HallStadium RoomEnjoying Surround Sound Adjusting each channel level with test tone Enter the test tone modeCancel the test tone function To cancel the surround mode for stereo operationAdjusting the current channel level Adjust the level of the selected channel as desiredRepeat the above steps 2 and 3 to adjust each channel level Press the Channel Level buttonMemorizing the adjusted channel levels Recalling the memorized channel levelsAuto tuning Manual tuningAuto presetting Press the Tuning UP+/DOWN- buttons for more than 0.5 secondManual presetting Tuning to preset stationsMEmORY BACkUP Function Repeat the above steps 1 to 3 to memorize other stationsRDS search TP searchFM mode, select the PTY search mode FM modePTY search While displaying PTY SRCH, select the desired program typeTo record audio signals Dubbing from video components onto VideoDigital Audio Recording with mD Recorder Displaying the operation status Operating the sleep timerAdjusting the brightness of the fluorescent display When using the buttons on the front panel Press the Room 2 button to enter the Room 2 modeSet the selected mode as desired Start play on the component related to the Room 2 sourceWhen using the buttons on the remote control unit Adjust the Room 2 volumeTurn on the Room 2 function Select the desired input as a Room 2 sourceTurn the menu screen on OSD Menu SettingsSelect the desired menu using the Cursor UP/DOWN buttons When selecting the System Setup When selecting the InputSetupWhen selecting the Sound Parameter When selecting the Speaker/Room EQ SetupSetup menu flow Bass TrebleVID1 CFG Setting the SYSTEm Setup When selecting the AmP Assign When selecting the Subwoofer modeWhen selecting the HDmI Audio Output When selecting the Tone ControlWhen selecting the Save/Recall When selecting the Cinema EQWhen selecting the momentary OSD When selecting the Auto Setup PreparationsTo memorize the results, press the Cursor Right button When selecting the Room EQ When selecting the Speaker Configuration Surround Surr Back SubwooferWhen selecting the Speaker Crossover Center Surround Surr BackWhen selecting the Speaker Distance About the speaker distanceWhen selecting the Channel Level When selecting the LFEMemorizing the adjusted channel levels and recalling them Setting the Input Setup When selecting the items other than Re-NameWhen selecting the HDmI Assign When selecting the Component AssignWhen selecting the Audio Assign When selecting the Video modeWhen selecting the AV Sync When selecting the Audio modeWhen selecting the Video Scaling When selecting the Re-Name When selecting the HD AudioTo resume its factory input source name To clear the name you enteredWhen selecting the Volume When selecting the RoomWhen selecting the Input When selecting the Dolby Pro Logic II music When selecting the Night modeWhen selecting the PReP When selecting the Detail EnhancementWhen selecting the Edge Enhancement When selecting the mosquito NRREmEDY Troubleshooting GuidePROBLEm Specifications Setup Code Table Inno HIT DOCK-VCR Otto Verand BD/DVD SAT AUX-USB/MD RD-8504
Related manuals
Manual 71 pages 21.87 Kb

RD-8504 specifications

The Sherwood RD-8504 is a powerful and versatile audio receiver designed for audiophiles and casual listeners alike. This unit elegantly combines modern technology with essential features, making it an attractive option for those seeking an immersive audio experience for their home theater or music listening setup.

At the heart of the RD-8504 is a robust amplifier capable of delivering 100 watts per channel, ensuring that even the most demanding speakers can operate at their peak performance. This power output allows for high volume levels without distortion, making it ideal for movies, music, and gaming. The receiver supports a wide range of speaker configurations, including 7.1 surround sound, enabling users to create a rich and enveloping audio environment.

One of the standout features of the Sherwood RD-8504 is its advanced Digital Signal Processing (DSP). This technology allows the receiver to provide multiple sound modes tailored to various content types, including movies, music, and sports. The DSP ensures that audio quality is maintained while optimizing the listening experience for different environments. Additionally, the receiver provides a built-in equalizer, which allows users to fine-tune sound settings to suit their personal preferences.

Connectivity is another strong suit of the RD-8504. The receiver is equipped with multiple HDMI inputs, making it easy to connect various devices such as game consoles, Blu-ray players, and streaming devices. The HDMI ARC feature also enables seamless audio transmission from compatible televisions. Beyond HDMI, the receiver includes analog and digital inputs, as well as USB connectivity for direct playback from external devices.

The RD-8504 also shines in its support for modern audio formats, including Dolby Digital and DTS, providing immersive surround sound that enhances the overall experience of films and music. Furthermore, it supports high-resolution audio formats, allowing users to enjoy lossless music playback and taking full advantage of today’s high-quality audio sources.

In terms of user interface, Sherwood has designed the RD-8504 with an intuitive layout and clear display. The front panel features easy-to-navigate buttons and a large LCD screen that provides essential information at a glance. The remote control offers comprehensive access to all features, enabling users to customize their listening preferences effortlessly.

In summary, the Sherwood RD-8504 receiver combines powerful amplification, advanced DSP technology, and extensive connectivity options to deliver an outstanding audio experience. Its blend of modern features and user-friendly design makes it an excellent choice for anyone looking to enhance their home entertainment system. Whether for a casual movie night or an immersive music session, the RD-8504 is poised to satisfy and impress.
Top Page Image Contents