Sherwood RD-8504 When using the buttons on the front panel, Set the selected mode as desired

Page 34

RD-8504(G)_ENG_091217:RD-8504(G) 2009-12-21 오￿ 11:36 페이지 34

ENGLISH

ROOm 2 SOURCE PLAYBACk

• This function allows enjoying one source in the main room and playing another in a different room at the same time.

Notes:

The analog signals from the EXTERNAL INs and the digital signals cannot be output to the different room, meaning no playback in a different room.

Only the (composite) video signals can be output to the different room.

When the EXTERNAL IN is selected as a main input, if the MAIN source is selected as a ROOM 2 input, no audio signal can be heard in the different room (ROOM 2).

Even when this receiver enters the standby mode, in such a case that only the "R2" lights up still, meaning only the ROOM 2 circuitry operates, the ROOM 2 source can be played independently.

When you do not use the ROOM 2 function, turn off the ROOM 2 function to save electricity.

When using the buttons on the front panel

1. Press the ROOM 2 button to enter the ROOM 2 mode.

• ROOM 2 ~ is displayed for several seconds.

• When the ROOM 2 setting mode disappears, press the ROOM 2 button again.

2. Select the desired mode while displaying the ROOM 2 setting mode.

• Each time these buttons are pressed, the mode changes as follows :

ROOM 2 ~ : To turn on or off the ROOM 2 function.

(ROOM 2 mode)

IN ~ : To select the desired ROOM 2 source.

(ROOM 2 input)

VOL ~ : To adjust the volume on the power (ROOM 2 volume) amplifier assigned to "Surr Back

Room 2" or "Room 2".

Note :

• When the ROOM 2 mode is set to OFF, the ROOM 2 input and the ROOM 2 volume cannot be selected.

3. Set the selected mode as desired.

When selecting the ROOm 2 mode.

ON : To turn on the ROOM 2 function. ("R2" lights up.)

OFF : To turn it off. ("R2" goes off.)

When selecting the ROOm 2 input.

• You can select the desired among MAIN source, TUNER, CD, F.AUX, TAPE, VIDEO 1 ~ VIDEO 4 as a ROOM 2 source.

When selecting the ROOm 2 volume.

You can adjust the volume on the power amplifier assigned to "Surr BackRoom 2" or "Room 2" when the ROOM 2 speaker terminals are connected to the speakers in a different room. (For details, refer to "When selecting the AMP Assign" on page 41.)

4. Start play on the component related to the ROOM 2 source.

34

Image 34
Contents RD-8504 Do not ExPOSE this Appliance to Rain or mOISTURE Introduction220 240 Contents Connecting Antennas System ConnectionsConnecting Video COmPONENTS Video conversionHDmI High Definition multimedia Interface connection *1 Connecting Audio COmPONENTSComponent video input default settings *2 Copyright protection systemConnecting ExTERNAL INS Digital input default settingsSurround back speakers Connecting SPEAkERSFront Bi-Amp Connections Speaker placement Connecting ROOm 2 Outs Connecting for SYSTEm ControlFront Panel Controls Fluorescent DisplayFront AUx in JACk Setup mIC JACkVideo 4 in JACkS Universal Remote Controls Function Table of the Numbered Buttons StopReMote contRoL oPeRAtIon RAnGe Entering a setup code Repeat the above steps 1 to 4 for each of your ComponentsRemoving a punch-through function Using a punch-through functionRemoving all punch-through functions To remove a macro program Programming a macro functionOperating a macro function To change a macro programOperations Standby mode, turn the power onSwitch the speakers on Before operationMuting the sound Listening with headphonesAdjust the overall volume Press the Audio Assign buttonSurround modes Stadium TheaterHall RoomEnjoying Surround Sound Cancel the test tone function Adjusting each channel level with test toneEnter the test tone mode To cancel the surround mode for stereo operationRepeat the above steps 2 and 3 to adjust each channel level Adjusting the current channel levelAdjust the level of the selected channel as desired Press the Channel Level buttonMemorizing the adjusted channel levels Recalling the memorized channel levelsAuto presetting Auto tuningManual tuning Press the Tuning UP+/DOWN- buttons for more than 0.5 secondMEmORY BACkUP Function Manual presettingTuning to preset stations Repeat the above steps 1 to 3 to memorize other stationsRDS search TP searchPTY search FM mode, select the PTY search modeFM mode While displaying PTY SRCH, select the desired program typeTo record audio signals Dubbing from video components onto VideoDigital Audio Recording with mD Recorder Adjusting the brightness of the fluorescent display Operating the sleep timerDisplaying the operation status Set the selected mode as desired When using the buttons on the front panelPress the Room 2 button to enter the Room 2 mode Start play on the component related to the Room 2 sourceTurn on the Room 2 function When using the buttons on the remote control unitAdjust the Room 2 volume Select the desired input as a Room 2 sourceSelect the desired menu using the Cursor UP/DOWN buttons OSD Menu SettingsTurn the menu screen on When selecting the Sound Parameter When selecting the System SetupWhen selecting the InputSetup When selecting the Speaker/Room EQ SetupSetup menu flow Bass TrebleVID1 CFG Setting the SYSTEm Setup When selecting the HDmI Audio Output When selecting the AmP AssignWhen selecting the Subwoofer mode When selecting the Tone ControlWhen selecting the momentary OSD When selecting the Cinema EQWhen selecting the Save/Recall When selecting the Auto Setup PreparationsTo memorize the results, press the Cursor Right button When selecting the Room EQ When selecting the Speaker Configuration Surround Surr Back SubwooferWhen selecting the Speaker Crossover Center Surround Surr BackWhen selecting the Speaker Distance About the speaker distanceWhen selecting the Channel Level When selecting the LFEMemorizing the adjusted channel levels and recalling them Setting the Input Setup When selecting the items other than Re-NameWhen selecting the Audio Assign When selecting the HDmI AssignWhen selecting the Component Assign When selecting the Video modeWhen selecting the Video Scaling When selecting the Audio modeWhen selecting the AV Sync When selecting the Re-Name When selecting the HD AudioTo resume its factory input source name To clear the name you enteredWhen selecting the Input When selecting the RoomWhen selecting the Volume When selecting the Dolby Pro Logic II music When selecting the Night modeWhen selecting the Edge Enhancement When selecting the PRePWhen selecting the Detail Enhancement When selecting the mosquito NRPROBLEm Troubleshooting GuideREmEDY Specifications Setup Code Table Inno HIT DOCK-VCR Otto Verand BD/DVD SAT AUX-USB/MD RD-8504
Related manuals
Manual 71 pages 21.87 Kb

RD-8504 specifications

The Sherwood RD-8504 is a powerful and versatile audio receiver designed for audiophiles and casual listeners alike. This unit elegantly combines modern technology with essential features, making it an attractive option for those seeking an immersive audio experience for their home theater or music listening setup.

At the heart of the RD-8504 is a robust amplifier capable of delivering 100 watts per channel, ensuring that even the most demanding speakers can operate at their peak performance. This power output allows for high volume levels without distortion, making it ideal for movies, music, and gaming. The receiver supports a wide range of speaker configurations, including 7.1 surround sound, enabling users to create a rich and enveloping audio environment.

One of the standout features of the Sherwood RD-8504 is its advanced Digital Signal Processing (DSP). This technology allows the receiver to provide multiple sound modes tailored to various content types, including movies, music, and sports. The DSP ensures that audio quality is maintained while optimizing the listening experience for different environments. Additionally, the receiver provides a built-in equalizer, which allows users to fine-tune sound settings to suit their personal preferences.

Connectivity is another strong suit of the RD-8504. The receiver is equipped with multiple HDMI inputs, making it easy to connect various devices such as game consoles, Blu-ray players, and streaming devices. The HDMI ARC feature also enables seamless audio transmission from compatible televisions. Beyond HDMI, the receiver includes analog and digital inputs, as well as USB connectivity for direct playback from external devices.

The RD-8504 also shines in its support for modern audio formats, including Dolby Digital and DTS, providing immersive surround sound that enhances the overall experience of films and music. Furthermore, it supports high-resolution audio formats, allowing users to enjoy lossless music playback and taking full advantage of today’s high-quality audio sources.

In terms of user interface, Sherwood has designed the RD-8504 with an intuitive layout and clear display. The front panel features easy-to-navigate buttons and a large LCD screen that provides essential information at a glance. The remote control offers comprehensive access to all features, enabling users to customize their listening preferences effortlessly.

In summary, the Sherwood RD-8504 receiver combines powerful amplification, advanced DSP technology, and extensive connectivity options to deliver an outstanding audio experience. Its blend of modern features and user-friendly design makes it an excellent choice for anyone looking to enhance their home entertainment system. Whether for a casual movie night or an immersive music session, the RD-8504 is poised to satisfy and impress.