Sherwood RD-8504 manual Auto tuning, Manual tuning, Auto presetting, Select the desired band

Page 27

RD-8504(G)_ENG_091217:RD-8504(G) 2009-12-21 오￿ 11:36 페이지 27

LISTENING TO RADIO BROADCASTS

Auto tuning

1. Select the desired band.

•Each time this button is pressed, the band changes as follows :

→ FM ST → FM MONO → AM ("ST" lights up) ("ST" goes off)

•When FM stereo broadcasts are poor because of weak broadcast signals, select the FM mono mode to reduce the noise, then FM broadcasts are reproduced in monaural sound.

2. Press the TUNING UP(+)/DOWN(-) buttons for more than 0.5 second.

•The tuner will now search until a station of sufficient strength has been found. The display shows the tuned frequency and "TUNE".

•If the station found is not the desired one, simply repeat this operation.

•Weak stations are skipped during auto tuning.

manual tuning

•Manual tuning is useful when you already know the frequency of the desired station.

•After selecting the desired band, press the TUNING UP(+)/DOWN(-) buttons repeatedly until the right frequency has been reached.

Auto presetting

•Auto presetting function automatically searches for FM stations only and store them in the memory.

•While listening to FM or AM radio broadcasts, press and hold down the (MEMORY/)ENTER button for more than 2 seconds.

•Then "AUTO MEM" flickers and this receiver starts auto presetting.

•To stop auto presetting, press this button again.

•Up to 30 FM stations can be stored.

■Notes:

•FM stations of weak strength cannot be memorized.

•To memorize AM stations or weak stations, preform "Manual presetting" procedure with using "Manual tuning" operation.

ENGLISH

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents RD-8504 Introduction Do not ExPOSE this Appliance to Rain or mOISTURE220 240 Contents System Connections Connecting AntennasVideo conversion Connecting Video COmPONENTSCopyright protection system Connecting Audio COmPONENTSComponent video input default settings *2 HDmI High Definition multimedia Interface connection *1Digital input default settings Connecting ExTERNAL INSConnecting SPEAkERS Surround back speakersFront Bi-Amp Connections Speaker placement Connecting for SYSTEm Control Connecting ROOm 2 OutsFluorescent Display Front Panel ControlsSetup mIC JACk Front AUx in JACkVideo 4 in JACkS Universal Remote Controls Stop Function Table of the Numbered ButtonsReMote contRoL oPeRAtIon RAnGe Repeat the above steps 1 to 4 for each of your Components Entering a setup codeUsing a punch-through function Removing a punch-through functionRemoving all punch-through functions To change a macro program Programming a macro functionOperating a macro function To remove a macro programBefore operation Standby mode, turn the power onSwitch the speakers on OperationsPress the Audio Assign button Listening with headphonesAdjust the overall volume Muting the soundSurround modes Room TheaterHall StadiumEnjoying Surround Sound To cancel the surround mode for stereo operation Adjusting each channel level with test toneEnter the test tone mode Cancel the test tone functionPress the Channel Level button Adjusting the current channel levelAdjust the level of the selected channel as desired Repeat the above steps 2 and 3 to adjust each channel levelRecalling the memorized channel levels Memorizing the adjusted channel levelsPress the Tuning UP+/DOWN- buttons for more than 0.5 second Auto tuningManual tuning Auto presettingRepeat the above steps 1 to 3 to memorize other stations Manual presettingTuning to preset stations MEmORY BACkUP FunctionTP search RDS searchWhile displaying PTY SRCH, select the desired program type FM mode, select the PTY search modeFM mode PTY searchDubbing from video components onto Video To record audio signalsDigital Audio Recording with mD Recorder Operating the sleep timer Adjusting the brightness of the fluorescent displayDisplaying the operation status Start play on the component related to the Room 2 source When using the buttons on the front panelPress the Room 2 button to enter the Room 2 mode Set the selected mode as desiredSelect the desired input as a Room 2 source When using the buttons on the remote control unitAdjust the Room 2 volume Turn on the Room 2 functionOSD Menu Settings Select the desired menu using the Cursor UP/DOWN buttonsTurn the menu screen on When selecting the Speaker/Room EQ Setup When selecting the System SetupWhen selecting the InputSetup When selecting the Sound ParameterBass Treble Setup menu flowVID1 CFG Setting the SYSTEm Setup When selecting the Tone Control When selecting the AmP AssignWhen selecting the Subwoofer mode When selecting the HDmI Audio OutputWhen selecting the Cinema EQ When selecting the momentary OSDWhen selecting the Save/Recall Preparations When selecting the Auto SetupTo memorize the results, press the Cursor Right button When selecting the Room EQ Surround Surr Back Subwoofer When selecting the Speaker ConfigurationCenter Surround Surr Back When selecting the Speaker CrossoverAbout the speaker distance When selecting the Speaker DistanceWhen selecting the LFE When selecting the Channel LevelMemorizing the adjusted channel levels and recalling them When selecting the items other than Re-Name Setting the Input SetupWhen selecting the Video mode When selecting the HDmI AssignWhen selecting the Component Assign When selecting the Audio AssignWhen selecting the Audio mode When selecting the Video ScalingWhen selecting the AV Sync When selecting the HD Audio When selecting the Re-NameTo clear the name you entered To resume its factory input source nameWhen selecting the Room When selecting the InputWhen selecting the Volume When selecting the Night mode When selecting the Dolby Pro Logic II musicWhen selecting the mosquito NR When selecting the PRePWhen selecting the Detail Enhancement When selecting the Edge EnhancementTroubleshooting Guide PROBLEmREmEDY Specifications Setup Code Table Inno HIT DOCK-VCR Otto Verand BD/DVD SAT AUX-USB/MD RD-8504
Related manuals
Manual 71 pages 21.87 Kb

RD-8504 specifications

The Sherwood RD-8504 is a powerful and versatile audio receiver designed for audiophiles and casual listeners alike. This unit elegantly combines modern technology with essential features, making it an attractive option for those seeking an immersive audio experience for their home theater or music listening setup.

At the heart of the RD-8504 is a robust amplifier capable of delivering 100 watts per channel, ensuring that even the most demanding speakers can operate at their peak performance. This power output allows for high volume levels without distortion, making it ideal for movies, music, and gaming. The receiver supports a wide range of speaker configurations, including 7.1 surround sound, enabling users to create a rich and enveloping audio environment.

One of the standout features of the Sherwood RD-8504 is its advanced Digital Signal Processing (DSP). This technology allows the receiver to provide multiple sound modes tailored to various content types, including movies, music, and sports. The DSP ensures that audio quality is maintained while optimizing the listening experience for different environments. Additionally, the receiver provides a built-in equalizer, which allows users to fine-tune sound settings to suit their personal preferences.

Connectivity is another strong suit of the RD-8504. The receiver is equipped with multiple HDMI inputs, making it easy to connect various devices such as game consoles, Blu-ray players, and streaming devices. The HDMI ARC feature also enables seamless audio transmission from compatible televisions. Beyond HDMI, the receiver includes analog and digital inputs, as well as USB connectivity for direct playback from external devices.

The RD-8504 also shines in its support for modern audio formats, including Dolby Digital and DTS, providing immersive surround sound that enhances the overall experience of films and music. Furthermore, it supports high-resolution audio formats, allowing users to enjoy lossless music playback and taking full advantage of today’s high-quality audio sources.

In terms of user interface, Sherwood has designed the RD-8504 with an intuitive layout and clear display. The front panel features easy-to-navigate buttons and a large LCD screen that provides essential information at a glance. The remote control offers comprehensive access to all features, enabling users to customize their listening preferences effortlessly.

In summary, the Sherwood RD-8504 receiver combines powerful amplification, advanced DSP technology, and extensive connectivity options to deliver an outstanding audio experience. Its blend of modern features and user-friendly design makes it an excellent choice for anyone looking to enhance their home entertainment system. Whether for a casual movie night or an immersive music session, the RD-8504 is poised to satisfy and impress.
Top Page Image Contents