Frigidaire 316423411 Setting Surface Controls cont’d, About the Radiant Surface Elements

Page 8

Setting Surface Controls (cont’d)

Warming Zone

Single Radiant

Single Radiant (some models)

Surface Control

Surface Control

Dual Radiant (some models)

(some models)

(some models)

Surface Control

Fig. 1

About the Radiant Surface Elements

The element temperature rises gradually and evenly. As the temperature rises, the element will glow red. To maintain the selected setting, the element will cycle ON and OFF. The heating element retains enough heat to provide a uniform and consistent heat during the off cycle.

For efficient cooking, turn OFF the element several minutes before cooking is complete. This will allow residual heat to complete the cooking process.

NOTE: Please read detailed instructions for ceramic glass cooktop cleaning in the General Care & Cleaning and Before You Call checklist sections of this Use & Care Manual.

ELEMENT ON

INDICATOR

HOT SURFACE

Element ON & Hot Surface Indicator Lights

Your range is equipped with two different types of radiant surface control

LIGHT

Fig. 2

INDICATOR LIGHT indicator lights that will glow on your range— the Element ON indicator light and the Hot Surface indicator lights (Refer to Fig. 2).

The Element ON indicator lights are located on the control panel above each radiant element control knob and will glow when a surface element is turned ON. A quick glance at this indicator light after cooking is an easy check to be sure ALL surface controls are turned OFF. The Hot Surface indicator light located on the control panel will glow when any surface cooking area heats up and will REMAIN ON until the glass cooktop has cooled to a MODERATE level.

NOTE: Radiant elements have a limiter that allows the element to cycle ON & OFF, even at the HI setting. This helps to prevent damage to the ceramic smoothtop. Cycling at the HI setting is normal and will occur more often if the cookware is too small for the radiant element or if the cookware bottom is not flat.

Single Radiant Surface Elements (all models)

To Operate a Single Radiant Element:

1. Place correctly sized cookware on radiant surface element.

2. Push in & turn the surface control knob in either direction to the desired setting (Refer to the Suggested Radiant Surface Element Settings Table & Fig. 3). Start most cooking operations on a higher setting and then turn to a lower setting to finish cooking. The surface control knobs do not have to be set exactly on a particular mark. Use the marks as a guide and adjust the control knob as needed. Each surface element provides a constant amount of heat at each setting. A glowing red surface heating area extending beyond the bottom edge of the cookware indicates the cookware is too small for the surface heating area.

3.When cooking is complete turn the surface element OFF before removing the cookware.

Note: The Element ON indicator lights will glow when one or more of the surface

 

elements are turned ON. A quick glance at these indicator lights when cooking is

 

finished is an easy check to be sure all control knobs are turned OFF. The Hot Surface

 

indicator light will continue to glow AFTER the control knob is turned to the OFF position

Fig. 3

& will glow until the heating surface area has cooled sufficiently.

 

Radiant surface elements may appear to have cooled after they have been turned OFF. The glass surface may still be hot and burns may occur if the glass surface is touched before it has cooled sufficiently.

DO NOT place plastic items such as salt & pepper shakers, spoon holders or plastic wrappings on top of the range when it is in use. These items could melt or ignite. Potholders, towels or wooden spoons could catch fire if placed too close to the surface elements.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Features at a Glance Before Setting Oven Controls Adjusting Oven TemperatureBefore You Call WelcomeProduct Registration Important Safety InstructionsWelcome & Congratulations Important Instructions for Using Your Cooktop Important Instructions for Usingyour Cooktop Cont’d When flaming foods under a ventilating hood, turn the fan onFeatures At a Glance Your Electric Range Features IncludeBefore Setting Oven Controls Setting Surface Controls Using proper cookwareSuggested Radiant Surface Element Settings Table Cookware Material TypesSetting Surface Controls cont’d Element on & Hot Surface Indicator LightsAbout the Radiant Surface Elements Single Radiant Surface Elements all modelsSurface areas that heat are shown in black Setting the Warming Zone some modelsSetting the Warming Zone Control Setting Oven Controls Temperature conversionOven Control Functions For a silent control panelSetting Oven Controls cont’d To Set the Clock To Set the Minute TimerTo Set or Change the Temperature for Baking To Set Control for Continuous Bake or 12 Hour Energy SavingSpeed Bake Cooking Instructions Speed Bake Cooking System some modelsHow Speed Bake Cooking System works To Set Speed Bake Cooking System Self-CleaningSetting Oven Controls cont’d When the Self-Clean Cycle has Completed Self-Cleaning cont’d Preparing for a Self-Clean CycleAdhere to the following cleaning precautions General Care & Cleaning Stainless SteelPlastic or foods with a high sugar content For heavy, burned on soilSpecial Caution for Aluminum Use on the Ceramic Cooktop Removing & Replacing the Lift-Off Oven DoorTo Remove Oven Door To Replace Oven DoorAdjusting Your Oven Temperature Care & Cleaning of Stainless Steel some modelsTo Adjust Oven Temperature Circuit Protection Models with electric outletsSolutions to Common Problems Before You CallMajor Appliance Warranty Information Exclusions This warranty does not cover the following

316423411 specifications

The Frigidaire 316423411 is a highly regarded oven bake element, designed to ensure efficient cooking and baking in various culinary settings. This component is widely compatible with several Frigidaire models, allowing users to replace old, malfunctioning elements with ease and confidence.

One of the main features of the Frigidaire 316423411 is its robust construction, which comprises durable materials that can withstand high temperatures. This durability ensures that the element can deliver consistent heating performance over time, reducing the likelihood of warping or breaking under stress.

The heating element itself has a power rating that typically falls around 2600 watts, which provides rapid heating capabilities. This power allows users to achieve high temperatures quickly, making it ideal for baking, roasting, and broiling. Consumers appreciate this feature as it saves both time and energy during meal preparation.

In addition to its impressive heat output, the Frigidaire 316423411 boasts even heat distribution. This technology ensures that food is cooked evenly, minimizing the risk of hot or cold spots. Home cooks can rely on this feature to achieve perfectly baked goods, such as cakes and cookies, while also ensuring that meats and vegetables are cooked thoroughly.

Another characteristic of the Frigidaire 316423411 is its user-friendly installation process. Most users can replace the element without requiring professional assistance. Detailed instructions provided with the product guide users through the installation steps, often requiring only basic tools and safety precautions.

The element is also designed with safety features that prevent overheating, thereby reducing the risk of kitchen accidents. Users can rest assured knowing that they have a reliable and safe component in their oven.

Overall, the Frigidaire 316423411 is a pivotal part of modern baking technology. Its combination of durability, efficient heating, even heat distribution, and user-friendly installation makes it an essential component for anyone looking to enhance their cooking experience. Whether you are an experienced chef or a novice baker, this element is sure to meet your cooking needs and contribute to delicious meals.
Top Page Image Contents