Frigidaire CGGF3054KF, 316901300 To assemble the Effortless Oven Rack system

Page 9

Effortless™ Oven Rack system

Some models are equipped with a special oven rack system that automatically partially extends the oven rack from the interior oven glides to assist in easier access to your food items. This feature works whenever the oven door is opened or closed.

To assemble the Effortless™ Oven Rack system:

1.

Locate all required parts. You will need the supplied

 

oven rack (Effortless™ Oven Rack is a flat rack with a

 

special dark coating on the left and right rack

 

sides) and the 2 supplied chrome connector arms.

2.

Open the oven door. Be sure the oven is completely

 

cool before proceeding.

3.

Place the oven rack in positions 2, 3 or 4 only (see

 

previous page to verify positions).Be sure the rack

 

connector brackets are at the rear of the range and

 

pointing towards oven bottom (See Fig. 2).

4.

Assemble one connector arm at a time. With the oven

BEFORE SETTING OVEN CONTROLS

IMPORTANT

Only the Effortless™ Oven Rack system should be used in oven rack position 2. Placing ANY other rack in oven rack position 2 will prevent the oven door from fully closing and may damage the oven door, oven cavity or the door connector brackets.

If the rack system is not assembled with the connector arms the Effortless™ Oven rack may be used in oven rack positions 2 thru 6. Do not attempt to use the Effortless™ Oven rack in rack position 1.

door

rack connector

connector

bracket

bracket

 

 

door open and the oven rack in place, install one end of

 

the connector arm to the hole in the door connector

 

bracket (Fig. 1) and the other end in the hole in the

 

rack connector bracket (Fig. 2 and as in Fig. 3). The

 

oven rack may need to be adjusted in or out in the rack

 

position to match the length of the connector arm.

5.

While holding the connector arm in place, twist the

 

connector arm so the ends of the connector arm point

 

upwards (See Figs. 4 & 5). The connector arm should

 

now be locked into position.

6.

Repeat steps 4 and 5 for the other connector arm.

7.

Once both connector arms are properly in place, be

Fig. 1

connector

arm

Fig. 3 - assembly of the Effortless™ Oven Rack

Fig. 2

oven rack

sure to test the oven rack operation by gently closing

the oven door. The oven rack should move in and out of

the oven freely when the door is opened or closed.

open oven

connector

door

arm

CAUTION

REMOVE ALL OVEN RACKS and accessories before starting a self-clean cycle. If the oven racks are left in the oven during the self-clean cycle, the glide ability of the Effortless™ Oven Rack system will be damaged and will cause oven racks to loose their shiny finish and or turn blue. Remove ALL oven racks and clean according to instructions provided in the Care & Cleaning section of this manual.

Make sure the oven and oven racks are COMPLETLY cool and safe to touch before attempting to assemble or disassemble the Effortless™ Oven Rack system. Never pick up hot oven rack parts.

connector arm

Fig. 4

connector

arm

Fig. 5

left and right

door connector

brackets

with connector arm ends shown in locked position (pointing upwards)

Fig. 6 - Effortless™ Oven Rack after assembly

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Use&Care Product Record and Registration ContentsDefinitions Important Safety InstructionsImportant Safety Instructions Important Instructions for Using Your Cooktop Conversion to Liquefied Petroleum Gas Grounding InstructionsYour gas range features include Features AT a GlanceBefore Setting Oven Controls Effortless Oven Rack system To assemble the Effortless Oven Rack systemSpecial dark coating on the left and right rack Using proper cookware Before Setting Surface ControlsCorrect flame setting Incorrect flame setting Set proper burner flame sizeSetting surface controls Setting Surface ControlsSetting a surface burner Seasoning, using and caring for the griddleMinimum & maximum control settings Feature Min. temp. /time Max. temp. /timeOven Control Functions Setting the clock Setting Oven ControlsSetting 12 or 24 hour display modes Changing oven temperature displaySetting oven lockout Setting a silent control panelSetting the minute timer Add a minute featureSetting bake Setting quick preheatSetting bake time When the set bake time runs outSetting Oven Controls Convect roast all models Convect bake all modelsSetting convect convection convert Broil Suggested broil settings table gas ovenTo set broil Step Press Close the oven doorSetting chicken nuggets feature Setting pizza featureSetting chicken nuggets feature cont’d Setting keep warmExample increase the oven temperature by 30F Step Press Adjusting the oven temperatureExample decrease the oven temperature by 30F Step Press Operating the oven lightTo Set the Sabbath Feature for use on If a timed bake or delayed timed bake is neededBake time and delay start pads To Set the Sabbath Feature cont’d SELF-CLEANING Self-cleaningAdhere to the following self-clean precautions Veryhot When the self-clean cycle has completedCleaning recommendation table Care & CleaningTo clean the burner head ignition ports Cleaning the cooktop and surface burnersTo clean the surface burner heads Replacing the oven lightRemoving and replacing the lift-off oven door To remove oven doorTo replace oven door Care & Cleaning section Problem SolutionBefore YOU Call Solutions to common problems Disclaimer of Implied Warranties Limitation of Remedies Major Appliance Warranty
Top Page Image Contents