Sherwood R-956 manual Multi Source Playback, Select the desired input as a Room 2 source

Page 28

ENGLISH

MULTI SOURCE PLAYBACK

This function allows enjoying one source in the main room and playing another in a different room at the same time.

The analog signals from the 6.1 CH DIRECT inputs as well as the digital signals from the coaxial or optical digital input cannot be outputted in the ROOM 2 OUTs, meaning no playback in a different room.

Select the desired input as a main source.

1

When playing video program source in the main room.

Example) When playing VIDEO 2.

When playing sound and image sources separately in the main room.

Example) When playing CD as sound source and VIDEO 1 as image source.

1) Select VIDEO 1 as image source.

1 2 3

4 5 6

7 8 9

Select VIDEO 2 as a main source.

VIDEO

0

1 2 3

4 5 6

7 8 9

or

VID SEL

VIDEO

0

HOME THEATER MASTER

RNC-30

or

VID SEL

HOME THEATER MASTER

RNC-30

2) Select CD as sound source.

1

2

3

4

5

6

7

8

9

AUDIO

0

 

 

 

When an audio program source is selected, the image of the video program source selected previously can be played separately.

or

CD

HOME THEATER MASTER

RNC-30

Note: Be sure to observe the order of the above steps 1) and 2).

2

ROOM2 FEED

Select the desired input as a ROOM 2 source.

 

 

On the remote control

 

AUDIO VIDEO

 

 

PHONO CD TUNER

 

 

 

 

 

 

 

ROOM 2

VID SEL

 

 

or

 

 

 

 

1

5

 

 

 

AUX

 

Press the ROOM 2 FEED button first and select one among “PHONO”, “TUNER”, “CD”, “AUX”, “VIDEO 1~5” by pressing the corresponding INPUT SELECTOR button, the selected ROOM 2 source is displayed for 3 seconds as follows; (R2) PHONO,

(R2) TUNER, (R2) CD, (R2) AUX, (R2) VIDEO 1~5.

When selecting one among “VIDEO 1~5” on the remote control, press the ROOM 2 FEED button first, the “VID SEL” button and then the corresponding numeric button among “1~5”.

Only these sources can be played in another room. When an audio program source is selected as a ROOM 2 source, the image of the video program source selected previously can be played separately, too.

3

Start play on the components related to

You will enjoy the corresponding sources in the

main source(s) and ROOM 2 source(s)

main room and in another respectively.

respectively.

 

2 8

Image 28
Contents 956 Introduction Read this Before Operating Contents Connecting Antennas System ConnectionsConnecting Video Components Connecting Speakers AC Input Cord Front Panel Controls Multi Control KnobUniversal Remote Control Digi Link System RemoteFunction Table of the Numbered Buttons Remote Control Loading BatteriesEntering a Setup Code Sherwood MD recorderListening to a Program OperationsBefore operation When CD, Tape MON or Video 1~ Video 4 is selected Adjusting the tone bass and trebleTo compensate for edgy or shrill movie Sound tracks Surround Sound Surround modesDelay time Speaker placementAdjusting the speaker settings Enjoying Surround SoundChecking the speaker setting Adjusting each channel levelAdjusting each channel level using test tones Downmixing into 2 front channels Manual tuning Listening to RadioPresetting radio stations Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsRecording Recording with Tape MonitorDigital Audio Recording with Multi Source Playback Select the desired input as a Room 2 sourceOther Functions Entering a video label Correcting or clearing a video labelCurrent Status Display Using the OSDMenu Screen Select the desired menu using the Cursor UP or Down button Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section956