Sherwood R-956 manual Listening to Radio, Manual tuning

Page 23

LISTENING TO RADIO

For some countries in the southeast asia, etc., AM frequency step of 10 kHz may be changed to 9 kHz according to the countries. To change to 9 kHz, do the following procedure.

1.Press the STANDBY button on the front panel while receiving AM broadcasts.

2.Press the STANDBY button while keeping the BAND button on the front panel pressed. To change to 10 kHz, do this procedure again.

Auto tuning

 

 

 

Select the desired band.

1

Select the tuner.

 

 

2 BAND

 

 

 

 

 

PWR

 

 

 

 

1

2

3

 

 

 

 

AUDIO

4

5

6

 

BAND

FREQUENCY

 

7

0

9

 

 

 

8

 

 

 

 

 

VOL

 

CH LEVL

 

 

 

 

 

or

ENTER

 

Each time this button is pressed, the band is changed

 

 

 

 

TUNER

to FM or AM.

 

 

 

 

 

 

 

When pressing the BAND button without first

 

 

 

RNC-30

 

selecting TUNER, the tuner will be selected

 

 

HOME THEATER MASTER

 

 

 

 

 

 

 

 

automatically.

 

 

3

Select the tuning mode.

Select the auto tuning mode as desired.

 

TUNING/PRESET

 

 

4

 

 

 

 

MODE

 

 

 

AUTO/MANUAL

 

Each time this button is pressed, the mode changes

Each time this button is pressed, the mode changes

as follows;

as follows;

 

 

Tuning mode : “PRESET” goes off.

 

 

 

 

Auto tuning mode : “AUTO” lights up.

 

 

 

 

 

 

 

 

 

 

 

Preset mode : “PRESET” lights up.

 

 

 

Manual tuning mode : “AUTO” goes off.

 

 

 

 

 

 

 

ENGLISH

Find the desired station.

5

MULTI CONTROL

 

DOWN UP

The tuner will now search until a station of sufficient strength has been found. The display shows the tuned frequency and “TUNED”.

If the station found is not the desired one, simply repeat this operation.

Weak stations are skipped during auto tuning.

Manual tuning

Manual tuning is useful when you already know the frequency of the desired station.

Perform the steps 1~3 in “Auto tuning”

1 procedure and select the manual tuning mode as desired.

AUTO/MANUAL

Rotate the MULTI CONTROL knob

2 repeatedly until the right frequency has been reached.

MULTI CONTROL

DOWN UP

Then “AUTO” goes off.

2 3

Image 23
Contents 956 Introduction Read this Before Operating Contents System Connections Connecting AntennasConnecting Video Components Connecting Speakers AC Input Cord Multi Control Knob Front Panel ControlsDigi Link System Remote Universal Remote ControlFunction Table of the Numbered Buttons Loading Batteries Remote ControlSherwood MD recorder Entering a Setup CodeBefore operation OperationsListening to a Program Adjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 4 is selectedTo compensate for edgy or shrill movie Sound tracks Surround modes Surround SoundSpeaker placement Delay timeEnjoying Surround Sound Adjusting the speaker settingsAdjusting each channel level Checking the speaker settingAdjusting each channel level using test tones Downmixing into 2 front channels Listening to Radio Manual tuningTuning to preset stations Presetting radio stationsListening to FM stereo broadcasts Scanning preset stations in sequenceRecording with Tape Monitor RecordingDigital Audio Recording with Select the desired input as a Room 2 source Multi Source PlaybackOther Functions Correcting or clearing a video label Entering a video labelMenu Screen Using the OSDCurrent Status Display Select the desired menu using the Cursor UP or Down button Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications956