Frigidaire Dual Fuel Range Slide-in Models warranty Before you call, Range is not level

Page 20

 

 

Before you call

 

Solutions to Common Problems

 

 

 

 

OCCURRENCE

 

POSSIBLE CAUSE/SOLUTION

Range is not level.

 

Poor installation. Place oven rack in center of oven. Place a level on the oven rack.

 

 

Adjust leveling legs at base of range until the rack is level. When range is level,

 

 

cooktop may appear out of alignment if countertop is not level.

 

 

 

 

 

 

Weak, unstable floor. Be sure floor is level and can adequately support range. If floor

 

 

is sagging or slopping, contact a carpenter to correct the situation.

 

 

 

 

 

 

Kitchen cabinet misalignment may make range appear to be unlevel. Be sure

 

 

cabinets are square and have sufficient room for range clearance.

 

 

 

 

Cannot move appliance easily. Appliance must be accessible for service.

Cabinets not square or are built in too tight. Contact a cabinet maker to correct the problem.

Contact builder or installer to make appliance accessible.

Carpet interferes with range. Provide sufficient space so range can be lifted over carpet.

Gas line is hard-plumbed. Have a flexible C.S.A international approved metal appliance connector installed.

Entire range or oven does not operate.

Make sure cord/plug is plugged tightly into outlet.

Service wiring is not complete. Call an authorized servicer.

Electrical power outage. Check house lights to be sure. Call your local electric company for service. Surface burners can be lit manually.

*Oven control beeps and displays any F code error (for example F11)

Electronic control has detected a fault condition. Press STOP/CLEAR to clear the display and stop beeping. Reprogram oven. If fault recurs, record fault number. Press STOP/CLEAR and call an authorized servicer for assistance.

Oven light does not work.

Replace or tighten bulb. See Changing Oven Light section in this Use & Care Guide.

Surface burners do not light.

Surface control knob has not been completely turned to LITE. Push in and turn the surface control knob to LITE until burner ignites and then turn the surface control knob to the desired flame size.

Burner ports are clogged. Clean burners. See “Cleaning the Burner Grates, Burner Caps and Burner Heads” under General Cleaning.

Range power is disconnected from outlet. Be sure cord is securely plugged into the outlet.

Electrical power outage.

Be sure the gas supply to the range is turned “ON”.

Surface burner flame burns half way around.

Burner ports or slots are clogged. With the burner off, use a small-gauge wire or needle to clean ports or slots.

Moisture is present after cleaning. Lightly fan the flame and allow the burner to operate until flame is full. Dry the burners thoroughly following instructions under General Cleaning.

20

Image 20
Contents Before Setting Welcome10-11 Before You CallWelcome & Congratulations Questions?Versión en español Register Your ProductWhat to do if YOU Smell GAS Important Safety InstructionsFor Your Safety Important Instructions for Usingyour Cooktop Conversion to Liquefied Petroleum Gas or L.P. Gas Features At a Glance Before Setting Surface Controls Control Locations of the Gas Surface BurnersRemember do not Allow SPILLS, Food 14K or 12KSetting Surface Controls Setting Proper Surface Burner Flame SizeOperating the Gas Surface Controls Flame Size Type of CookingBefore Setting Oven Controls Arranging Oven RacksRemoving and Replacing Oven Racks Oven VentSetting Warm & Serve Drawer Controls some models Using the Warm & Serve DrawerAir Circulation in the Oven Arranging Warm & Serve Drawer Rack PositionsSetting Oven Controls Warm & Serve Drawer Temperature SelectionTo Set the Warm & Serve Drawer Controls Food ItemCooking Informations Oven BakingBroiling Care & Cleaning Self-CleaningTo Set the Self-Clean Cycle Self-Cleaning OvenSurfaces How to Clean Control PanelsStainless Steel some models Oven door & drawer front panel Easier into the rack positionsCleaning the Cooktop, Burner Heads, Caps & Grates Allow SPILLS, FOOD, Cleaning Agents or ANY Other Material toRemoving and Replacing the Oven Door Hinge Slot Door re- moved from the oven FigureLock in normal position To Remove Oven DoorRemoving and Replacing Warm & Serve Drawer To Remove Warm & Serve DrawerAdjusting Your Oven Temperature Place When the Oven is in USEChanging Oven Light To Remove the Hidden Bake Cover some modelsBefore you call Range is not levelEntire range or oven does not operate Surface burner flame burns half way aroundSelf-cleaning cycle does not work Soil not completely removed after self- cleaning cycleSurface burner flame is orange Poor baking resultsMajor Appliance Warranty Information Exclusions