Sherwood RD-7106 manual Troubleshooting Guide, Problem Possible Cause Remedy

Page 27

Troubleshooting Guide

If a fault occurs, run through the table below before taking your receiver for repair.

If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult your dealer. Under no circumstances should you repair the receiver yourself as this could invalidate the guarantee!

PROBLEM

POSSIBLE CAUSE

REMEDY

 

 

 

No power

• The AC input cord is disconnected.

• Connect cord securely.

 

• Poor connection at AC wall outlet or the

• Check the outlet using a lamp or another

 

outlet is dead or off.

appliance.

 

 

 

No sound

• The speaker wires are disconnected.

• Check the speaker connections.

 

• The master volume is adjusted too low.

• Adjust the master volume.

 

• The MUTE button on the remote control is

• Press the MUTE button to cancel the

 

pressed to ON.

muting effect.

 

• Speakers are not switched on.

• Press the SPEAKER button to ON.

 

• Incorrect selection of an input source.

• Select the desired input source correctly.

 

• Incorrect connections between the components.

• Make connections correctly.

 

 

 

No sound from the rear

• Surround mode is switched off.(normal

• Select a surround mode.

speakers

stereo mode)

• Adjust master volume and rear level.

 

• Master volume and rear level are too low.

 

• Monaural source is used.

• Select a stereo or surround source.

 

• Rear speaker setting is “N”.

• Select the desired rear speaker setting.

 

 

 

No sound from the center

• Surround mode is switched off(normal stereo

• Select the desired surround mode.

speaker

mode).

• Select the desired center speaker setting.

 

• Center speaker setting is “N”.

 

• Master volume and center level are too low.

• Adjust master volume and center level.

 

 

 

Stations cannot be received.

• No antenna is connected.

• Connect an antenna.

 

• The desired station frequency is not tuned in.

• Tune in the desired station frequency.

 

• Antenna is in wrong position.

• Move antenna and retry tuning.

 

 

 

Preset stations cannot be

• An incorrect station frequency has been

• Memorize the correct station frequency.

received.

memorized.

• Memorize the stations again.

 

• The memorized stations are cleared.

 

 

 

Poor FM reception

• No antenna is connected.

• Connect an antenna.

 

• The antenna is not positioned for the best

• Change the position of the antenna.

 

reception.

 

 

 

 

Continuous hissing noise during

• Weak signals.

• Change the position of the antenna.

FM reception, especially when

 

• Install an outdoor FM antenna.

a stereo broadcast is received.

 

 

 

 

 

Continuous or intermittent

• Noise is caused by motors, fluorescent

• Keep the receiver away from noise sources.

hissing noise during AM

lamps or lightning, etc.

• Install an outdoor AM antenna.

reception, especially at night.

 

 

 

 

 

Remote control unit does not

• Batteries are not loaded or exhausted.

• Replace the batteries.

operate.

• The remote sensor is obstructed.

• Remove the obstacle.

 

 

 

Other Sherwood components

• DIGI LINK connections are not made

• Make proper DIGI LINK connections.

do not react to remote control

properly.

 

commands.

 

 

 

 

 

OSD function is not available.

• Video connections between this unit and the

• Make proper video connections.

 

monitor TV are not made correctly.

 

 

 

 

No sound

• The surround mode does not match the signal

• Select the “IN-AUTO” mode by pressing the

 

inputted.

AUTO button after selecting the digital input.

 

 

 

Delay time cannot be

• Under abnormal condition, delay time may

• After turning the menu screen off, adjust delay

adjusted.

not be adjusted on the delay time menu of

time by using the DELAY TIME and DELAY

 

OSD.

ADJUST buttons on the remote control.

 

 

 

ENGLISH

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents RD-7106 Introduction Unpacking and InstallationRead this Before Operating Your Unit Using the OSD System Connections Connecting Audio Components Connecting Video ComponentsConnecting Digital Inputs Connecting Speakers Connecting 6 CH Direct Inputs AC Input Cord A S Front Panel ControlsPower Button CD Player Section Digi Link III System Remote ControlsLoading Batteries Remote Control Operation RangeBefore operation OperationsAdjusting the tone bass and treble When CD, Video 1~VIDEO 4 is selected as an input sourceTo compensate for edgy or shrill movie Surround modes Surround SoundSpeaker placement Delay timeEnjoying Surround Sound Adjusting the speaker settingsAdjusting each channel level Checking the speaker settingAdjusting each channel level with test tone Downmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsMemory Backup Function Tuning to preset stationsRecording Recording with Tape MonitorDubbing from video components onto Separately onto Video Dubbing the audio and video signalsOther Functions Using the OSD Current Status DisplayMenu Screen When selecting the Function Select Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section SpecificationsRD-7106

RD-7106 specifications

The Sherwood RD-7106 is a versatile and powerful stereo receiver that has gained popularity among both audiophiles and casual listeners. Designed with an emphasis on performance and user-friendly functionality, the RD-7106 delivers a robust audio experience that enhances any home entertainment system.

One of the standout features of the Sherwood RD-7106 is its high-power output, which can deliver up to 50 watts per channel at 8 ohms. This ensures that the receiver can easily drive a wide range of speakers, providing rich and dynamic sound whether you're listening to music, watching movies, or enjoying gaming. The receiver’s classically styled front panel includes an array of knobs and buttons that make operation intuitive and straightforward.

The RD-7106 is equipped with advanced audio technologies including a built-in AM/FM tuner with a digital frequency display, allowing users to easily access their favorite radio stations. The receiver also supports auxiliary inputs, making it simple to connect external devices such as smartphones, tablets, or CD players. Its phono input enables direct connection to a turntable, appealing to vinyl enthusiasts and adding depth to the listening experience.

One of the key characteristics of the Sherwood RD-7106 is its robust construction. Built with high-quality components, the receiver provides exceptional durability and longevity, ensuring years of consistent performance. Its heat management is enhanced by a well-ventilated design, which prevents thermal buildup, allowing it to operate efficiently even during extended use.

Additionally, the RD-7106 features adjustable bass and treble controls, enabling users to tailor their sound preferences. This level of customization enhances the listening experience, allowing users to adjust the audio output according to the acoustics of their room or personal taste.

Another highlight is the receiver’s sleek and timeless aesthetic, which fits seamlessly into any home decor. Its minimalist design, with a brushed aluminum finish and warm lighting, emphasizes practicality without sacrificing style.

In summary, the Sherwood RD-7106 stands out as a reliable stereo receiver that combines high-performance audio capabilities with user-friendly features. Its versatile connectivity options, robust build quality, and customizable sound settings make it a solid choice for anyone looking to elevate their audio experience. Whether for music or movies, the RD-7106 delivers excellence, making it a worthy addition to your home audio setup.
Top Page Image Contents